Remote Vehicle Control System PC 4100 TM Owner's Manual Vehicle Security System IMPORTANT NOTE: The operation of the Power Elite as described in this manual is applicable to most vehicles. However, due to the engine type and configuration of some vehicles (i.e. diesel engines), some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
Table of Contents Features and Benefits of the Power Elite PC 4100TM ...................... 3 Using Your Remote Transmitter .............................................. 4 Arming the Security System Pre-arm Mode Disarming the Security System Attempted Intrusion Identification Disabling the IT-sTM Interior Theft Sensor ............................... 5 Two-Stage Door Unlock Activating the Trunk Release Feature Personal Protection Alarm (Panic) Using Valet Mode When Your Security System is Triggered ....
Features and Benefits of the Power Elite PC 4100TM Two Easy-to-Use Weather-Resistant Remote Controls The remote controls included with the Power Elite PC 4100TM utilize durable, moisture resistant cases and sealed rubber buttons for reliability and long life. Rolling code technology prevents the transmitter signals from being duplicated. The button functions are clearly labeled to make the Power Elite PC 4100TM simple to operate.
Using Your Remote Transmitter Press to ARM the Security System and Lock Doors Press for Car Finder Press to DISARM Security System and Unlock Doors Press TWICE for Two-Stage Door Unlock* Press and Hold for Panic Alarm Press and Hold to Open Trunk Press for two-car operation (SHIFT) Arming the Security System To arm the system, exit the vehicle, close all doors, then press* the ARM button. The horn** will “honk” twice† and the parking lights will flash twice, indicating the system is armed.
Using Your Remote Transmitter (cont.) Disabling the IT-sTM Interior Theft Sensor It may be necessary at times to disable the IT-sTM Interior Theft Sensor, especially when parking in areas (like parking garages) where extreme vibration may cause false alarms. Press the ARM button and then press the FIND/PANIC button within two seconds of pressing ARM to disable the interior theft sensor. The siren will chirp three times to indicate that the sensor is disabled.
Automatic Convenience Options The Power Elite PC 4100TM performs a variety of automatic functions to enhance security and comfort. Some of these features are programmable at the time of installation. Please see your installer for further details. Automatic Arming The Power Elite PC 4100TM will arm automatically 1 minute after the key is removed from the ignition. This feature can be temporarily disabled by placing the system into Valet mode.
System Maintenance Changing the Remote Control Battery The two 3-v lithium batteries (CR2016) supplied in your remote control should last approximately one year, depending on usage. When the battery begins to weaken, you will notice a decrease in range, or the distance from your vehicle that your remote transmitter will operate. Follow the instructions below to change the remote transmitter battery. 1. Insert the edge of a coin into the slot at the top of the remote control.
Basic Troubleshooting This section outlines some of the basic issues you may experience while becoming used to the Power Elite PC 4100TM. If you have a problem that is not covered by this section, please consult your installer.
Emergency Disarm Procedure If your remote control is lost or fails to function, use this procedure to disarm the Power Elite PC 4100TM and start your vehicle. 1. Use the keys to enter the vehicle. The alarm will sound once the door is opened. 2. Insert the key into the ignition and turn to the ON position. 3. Locate and press the emergency override button. The alarm will turn off and then you will be able to start your vehicle.
CODE-ALARM, INC. LIMITED LIFETIME WARRANTY A CODE-ALARM, INC. (“CODE”) vehicle security system sold to a retail consumer purchaser by an authorized dealer of CODE and installed by an authorized dealer of CODE is warranted by CODE to the original retail consumer purchaser to be free from defects in workmanship and materials for the lifetime of the vehicle in which the security system was originally installed.
CODE-ALARM, INC. Theft Protection Plan The Theft Protection Program is designed to provide the retail purchaser of a security system provided by CODE-ALARM, INC. (“CODE”) an additional benefit, at no additional cost to the purchaser, should their vehicle be stolen while protected by a CODE-ALARM security system.
Notes: FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Warning! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Notes:
Notes:
Notes: