Sentry-H 6110-MP OPERATOR GUIDE
No part of this manual may be reproduced, transcribed, translated into any language or transmitted in any form whatsoever without the prior written consent of Codan Communications. © Copyright 2019 Codan Communications. Codan part number 15-04200-EN Issue 1, December, 2019. CODAN®, Sentry®, and CALM® are trademarks of Codan Limited. Other brand, product, and company names mentioned in this document are trademarks or registered trademarks of their respective holders.
TABLE OF CONTENTS Table of Contents Preparing your radio Charging and installing batteries................................................................................................ 3 Attaching a ground wire to the radio.......................................................................................... 5 Inserting a 6110-MP into a backpack ........................................................................................ 7 Selecting and connecting your antenna.............................
TABLE OF CONTENTS Troubleshooting ....................................................................................................................... 56 Definitions................................................................................................................................. 62 Menu Navigation ......................................................................................................................
Charging and installing batteries Charging and installing batteries Check batteries Before any deployment, it is vital to ensure that your batteries are fully charged and that you have a sufficient number of batteries for your mission. Compatible batteries The 6110-MP is recommended for use with the following batteries available from Codan. Codan Part Number Battery Battery Chemistry Rechargeable Capacity 65-72015 BB-390B/U Nickel Metal Hydride Yes 9.
Charging and installing batteries Inserting your battery into the radio The battery is connected to the (J7) Connector located on the bottom of the radio and housed in a latching battery compartment. The image below shows the placement and alignment of the battery, battery compartment and radio.
Attaching a ground wire to the radio Attaching a ground wire to the radio To ensure optimal radio performance, the radio will need to be suitably grounded by fixing the antenna to an adequate ground point or by connecting a counterpoise. The 6110-MP radio has a ground lug located underneath the left handle of the radio, connect the grounding kit (Codan Part Number: 15-60083) to the ground lug by pressing down on the lug to reveal the ground clip insertion slot.
Attaching a ground wire to the radio AD LEP H I RT CL EA ND A OR SE OI P ER NT U CO Page 6 Sentry-H 6110-MP Operator Guide
Inserting a 6110-MP into a backpack Inserting a 6110-MP into a backpack All Codan supplied backpacks come with an adjustable harness that holds the radio firmly in position. The radio can be oriented so that the antenna port (J1) is located on either the right or left side of the backpack. accessory passthrough elastic loops 6110-MP radio radio harness To insert the radio into the soft backpack: 1. Open the backpack to expose the harness. 2.
Selecting and connecting your antenna Selecting and connecting your antenna Selecting an antenna It is crucial that you choose an antenna that meets your requirements. The table below provides an overview of Codan tactical antennas and the capabilities of each antenna over distance. Correct installation and positioning of your antenna is essential for quality HF communication. WARNING: This table provides an overview that is general in nature.
Selecting and connecting your antenna Connecting your antenna Your antenna is connected to the 6110-MP using the Antenna port (J1) on the front of the radio. Tunable antennas like the Tactical Whip antenna (Codan Part Number: 15-00473) and Tactical Long Wire (Codan Part Number: 15-00476) have a quick connect/release adaptor that connects to the antenna port (J1), the quick connect/release adaptor activates the internal tuner on the radio.
Testing your radio before deployment Testing your radio before deployment Once assembled, the radio should be tested to ensure that everything is working correctly. The following tests should be run before the radio is deployed. Testing involves: • running a diagnostic self-test; and • measuring the standing wave ratio (SWR) of your channels; and • carrying out station-to-station on-air testing.
Testing your radio before deployment The radio will now run through all of the self tests listed on the Self Tests screen. As each test is completed, the test result will appear on the screen. Passed Failed Manual (blank) Manual tests are tests that require you to run the test manually. 5. The CP LCD test checks for any screen errors by displaying the colour and tone states of the screen, the screen displays White, Black, Red, Green and Blue in order.
Testing your radio before deployment Measuring the Standing Wave Ratio (SWR) of your channels The 6110-MP radio measures the forward and reflected power between the radio and the antenna. The measured power ratio is called the Standing Wave Ratio or SWR. To ensure correct installation, the power and SWR assessment should be performed with the radio with any antenna you intend on using when deployed.
Testing your radio before deployment Tuning a channel or frequency Individual channels and frequencies can also be tested for their SWR value. To tune a single channel or frequency: 1. Select the channel or frequency you want to test from the Channel or Scratch Mode on the Operational screen (page 19). 2. Press the 3. Press the Push-To-Talk (PTT) button on the H-250 or 2320 handset (page 23). 4. Check the SWR value and address any problems before deployment. Sentry-H 6110-MP Operator Guide key.
Testing your radio before deployment On-air testing On-air testing gives a better indication of antenna operation, particularly if the operator is familiar with the signal strengths usually received within a network. The Channel Test call (page 39) can be used to identify the best channel between two stations. A test call between two closely positioned stations should return call quality results close to 100%.
Front panel and screen overview Front panel and screen overview The Sentry-H 6110-MP front panel screen power key internal gps antenna alert key control point port (J6) antenna port (J1) usb port (J9) front panel speaker H-250 port (J5) discreet mode switch GPS antenna port (J4) navigation keys keypad Switching the radio on and off Switching on Press the key. Switching off Hold the key for 2 seconds.
Front panel and screen overview The notification/title/tab bar The notification, title or tab bar is located at the top of the screen and is used to display useful information based on the current screen being displayed. Notification bar The notification bar is shown on the Operational screen (page 19), it displays the state of several of the radios key functions.
Front panel and screen overview Title bar The title bar is shown on the menu screen (page 20), it displays the current menu or sub-menu title. Tab bar The tab bar is a variant of the title bar. It is used to group menu items that are related, for example, grouping Time and Date settings. When a tab bar is selected, you can use the and navigation keys to cycle through the tabs. You can then use the and keys to navigate into the menu.
Front panel and screen overview The work area The work area is displayed below the notification bar and is the main work area of any screen. On the operational screen (page 19) displays important information about the state of the radio. On the menu screen (page 20), the work area displays menu items or settings. The menu bar The menu bar is displayed at the bottom of the screen and displays context for the software keys and .
Front panel and screen overview • Up/Down navigation is available . • Up/Down/Left/Right navigation is available . Screens overview There are several key screens that make up the 6110-MP user interface, being aware of each screen type is essential to successfully operating the radio. The Operational screen The operational screen displays information relating to the three main operating modes of the radio.
Front panel and screen overview Rx/Tx level indicator Tx power setting call type indicator mute type indicator (highlighted when mute is on) battery level indicator Rx/Tx indicator channel name missed call icon Tx/Rx frequency status areas mode indicator menu bar left software key right software key volume/speaker mode indicator The Menu screen The menu screen displays all user and system-level configurations for the radio, provides information about the radio and allows access to advanced views
Front panel and screen overview You can access the menu screen by pressing from the Operational screen (page 19) when in Scanning or Channel mode. The Call screen The Call screen is displayed when making a call to a station. It contains information about the call type, HF network in use. You can access the call screen by pressing from the Operational screen (page 19).
Front panel and screen overview 3. Press (Save) to save the setting. Set Auto Dim Time To change the number of seconds of no input before the screen is automatically dimmed: 1. Press the key. 2. Press 3. Enter the auto dim-time (in seconds), from 5 to 1200 seconds (20 min). 4. Press to navigate to the Set Auto Dim Time tab, then press . (Save) to save the change. Select the next available theme To switch between a Military Light and Military Dark theme: 1. Hold the Theme key.
Handsets Handsets The H-250 Handset The 6110-MP radio supports standard audio accessories with U-229 type connectors. The handset is a standard issue, lightweight, tactical H-250/U type, with built-in earphone, noisecancelling microphone, and PTT (Push To Talk) button. It is connected to the H-250 Audio port (J5) on the front panel of the radio.
Handsets The 2320 Handset The 2320 handset meets MIL-STD-810G environmental standards for shock, vibration, dust, humidity and IP67 for water and immersion. With an internal microphone and earphone/speaker, and cradle, the smart handset is designed to provide extended operation and control of the 6110-MP radio. Note: The 2320 handset and the front panel user interfaces are independent of one another.
Speaker and mute Speaker and mute Change the speaker volume The 6110-MP has a front speaker that outputs both received audio as well as system tones. You can adjust the speaker volume using the volume keys on the front panel. Use the increase the speaker volume and key to to decrease the volume when you are on the channel screen.
Speaker and mute Select mute type Mute type Icon Description Voice Mute is opened when speech is detected on a channel in all supported modes and when receiving a call addressed to the radio. Selective Mute is opened when a call addressed to you is detected Digital Mute is opened when digital voice is detected To select the next mute type, from the channel screen: 1. Press the key.
Discreet mode and zeroise Discreet mode and zeroise Discreet mode switch The discreet mode switch allows the operator to control audio and light emissions from the radio, that is to say, that all of the speakers and backlighting on the device turn off when in discreet mode, allowing the device to operate with reduced sound and light signature.
Discreet mode and zeroise To turn on discreet mode: 1. Set the discreet mode switch to To turn off discreet mode: 1. Set the discreet mode switch to Zeroise the radio There are two actions that the Zeroise function can execute on the radio. The lock action will turn the radio off and will force the operator to enter the Administrator PIN when the radio starts up again. The erase action will erase all user configurations, returning the radio to its factory state, it will then turn the radio off.
Secure communications Secure communications Secure mode is a macro that toggles two optional features of the 6110-MP radio, digital voice and voice/data encryption. By default, the secure macro will: • activate and deactivate AES-256 encrypted digital voice and data; or • if encryption is not available, activate and deactivate digital voice if available; or • activate CES-128 encryption if available.
Secure communications To select a secure key, from the channel screen: key to navigate to the secure info screen. • Hold the • Navigate to the Select Key Index option and press or to select the key you want to activate. • Press to Activate the key change. Selecting the Digital Voice rate The Digital Voice rate or DV rate is the bitrate of vocoder used for the digital voice transmission.
Secure communications Frequency hopping Codan’s Frequency Hopping capability (Codan Part Number: 15-10629-000) uses GPS timing to synchronise radios accurately. The 6110-MP radio may require a GPS antenna (Codan Part Number: 78-01253) connected to the radio’s GPS antenna port (J4) to get GPS time synchronisation. Note: To use Frequency Hopping your radio must have both the Hop and Hop Info macros assigned to a key, typically . To turn Frequency Hopping on and off: 1.
Entering and editing text Entering and editing text Entering text with a USB keyboard A Ruggedised USB Keyboard (Codan Part Number: 78-11005) can be connected to the USB port on the front of the radio (J9), a standard USB A (female) to 2320 USB adaptor cable (Codan Part Number: 08-07436-001) is required. In addition to text entry, navigation of the radios user interface can be achieved using a keyboard.
Entering and editing text Key Function Ctrl + Enter Inserts a new line if allowed Ctrl + Shift Opens the Select Input Language Screen when applicable Alt + * Opens the special characters popup when applicable Entering a special character with the keypad You can enter special characters in messages, names, stations, and in addresses of stations that you call. The key may be used to enter the global ALL address syntax (@?@) or special 2G ALE addressing characters easily.
Scanning, channel and scratch modes Scanning, channel and scratch modes The operational screen displays information relating to the three main operating modes of the radio desribed below.
Scanning, channel and scratch modes To select a fixed channel: 1. If you are in a menu screen, press PTT to exit to the operational screen. 2. If the radio is scanning, press Note: If the scan indicator icon 16), press 3. Press or to switch off scanning. is shown in the notification bar (page to turn off scanning. to scroll to the channel that you want to use. The channel is selected. Note: The channel mute will be temporarily open while navigating channels.
Scanning, channel and scratch modes tuned frequency numeric input To enter Scratch mode: 1. Ensure that the radio is in Channel mode (page 34). 2. Press the key to enter Scratch mode. Selecting a fixed frequency To select a fixed frequency in Scratch mode: 1. Press the (Select) key until the numeric input icon is displayed in the Menu bar (page 18) 2. Use the keypad to enter the frequency you want to tune. 3. Press to change.
HF networks HF networks An HF Network in the context of your radio is a call system with associated scan tables and several settings to control privacy and call establishment. The Sentry-H 6110-MP radio supports 2G ALE, 3G ALE and Codan Selcall call systems.
HF networks View and change HF network There may be several HF networks are available on your radio, and you may, at some point, need to change the network that you are using. The current HF network appears in the top right corner of the CALL screen. Note: The radio will automatically use appropriate call systems when scanning multiple HF networks. To set or change the HF network: Page 38 1. Press . 2. Press 3. Select HF Networks. 4. Select the desired HF network from the list. 5.
Call types Call types The 6110-MP is capable of making and receiving various call types; additional call types are available through the installation of optional accessories. Refer to the Operator Manual of your accessory for information on its features. Call Type Icon Network Description ALE Sounding 2G/3G ALE Channel Test ALL Test the signal quality between two stations. Alert ALL Make an alert call.
Call types 2G ALE special address calls Call Type Icon Description ALL An ALL call may be made to all stations that are tuned to or scanning the same frequency in a 2G ALE/CALM HF network. The ALL address syntax may be used with the Alert, Message, Phone, Selective, or Send Position call type. ANY An ANY call may be made to all stations that are tuned to or scanning the same frequency in a 2G ALE/CALM HF network.
Call types 3G ALE group and broadcast calls Call type Icon Description Group call A 3G ALE Group call enables multiple stations to be grouped as a single address. Groups are defined in the 3G ALE HF network configuration. Broadcast call A 3G ALE Broadcast call is a call made to all stations on your 3G ALE HF network that are configured to accept broadcast calls. Entering the address 1023 starts the call.
Answering and ending a call Answering and ending a call Answering a call 1. Press the PTT button to answer a call. Ending a call To end a call: 1. Page 42 Press the key to end a call.
Making a 2G or 3G ALE call Making a 2G or 3G ALE call Point-to-Point call A point-to-point call is a general term used to describe a transmission between two radios. There are several types of calls you can make using your radio. Refer to the call types (page 39) for more information about the types of calls that are available.
Making a 2G or 3G ALE call Making 2G ALE special address calls Note: Press the key to enter the ?, comma (,) and @ symbols when entering special addresses. To start a call: Page 44 1. Press the key. 2. Select a call type using the 3. Press the 4. Enter the address of the stations you want to call. 5. Press the 6. Enter a text message or select a menu item if prompted. 7. Press and keys. key, scroll to ALE and press . key. to begin the call.
Making a 2G or 3G ALE call 2G ALE special address syntax The Wildcard special address syntax is used to address calls to multiple stations within a 2G ALE HF network. The table below provides examples of the types of Note: The ?, comma (,), and @ characters are entered using the key.
Making a 2G or 3G ALE call In-link messaging In-link messages can be sent while on a 2G ALE selective or alert call. To send an In-Link message during a Selective or Alert call: Page 46 1. Press , the InLink Message screen is displayed. 2. Type your message. 3. Press (Options), scroll to Call and press to send the message.
Making a 2G or 3G ALE call 3G ALE Group and Broadcast calls 3G ALE Group calls Note: The Voice Message call type is not a valid group call. To make a 3G ALE group call: 1. Press the key. 2. Press the key, scroll to Groups, then press the 3. Press the or 4. Enter the group address or scroll through the group list. 5. Press the key. keys to select the call type you want to make. key to begin the call. 3G ALE Broadcast calls Note: The Voice Message call type is not a valid group call.
Making a 2G or 3G ALE call Asynchronous calling 3G ALE HF networks rely on each station on the network having syncronised clocks. Time synchronisation is achieved by using the signals from GPS satellites. If a radio is unable to receive GPS signals, their clock will over time lose sync with the rest of the 3G ALE HF network and will not be able to receive 3G ALE calls. If the station you are calling is not answering your call, it may be that their radios clock is out of sync.
Making a Selcall call Making a Selcall call To start a call: 1. Press the 2. Select a call type using the 3. Enter the address that you want to call. 4. Press the 5. Select a channel if prompted. 6. Press the 7. Enter a text message or select a menu item if prompted. 8. Press Sentry-H 6110-MP Operator Guide key. and keys. key. key. to begin the call.
Stations Stations Create a Station Creating a station call allows you to assign an alias to an address for easier identification. Likely, your HF Network Administrator has already configured several key stations on your radio. To create a new station; from the menu screen: (User Data), then select 1. Navigate to (Stations). 2. Press the 3. Enter the name of the station using the keypad. 4. Press the 5. Choose the network and call type you want to create for your contact. 6.
Stations Adding a Station from the Call History To add a station from the Call Log, Call History, or Last Heard Log: 1. Hold the key to show the Stations and Station History screen. 2. Select the Call History tab. 3. Scroll up or down to find the call that you want to save. 4. Press Left Menu (Options), scroll to Save, then press (Select). You are informed if there is a matching station for the address in the call and asked whether or not you want to append this call to that station.
Viewing GPS Information Viewing GPS Information Obtaining your position The GPS screen shows the GPS information obatined from a GPS receiver or latitude and longitude readings from a GPS receiver, or from Settings > GPS > My Position. Altitude and speed readings are hidden by default. The spinning circle shows that the GPS receiver is active, and the Last Fix reading shows the time lapse from the last receipt of valid GPS information.
Viewing GPS Information Distance and bearing The Sentry-H 6110-MP radio calculates distance and bearing information between your GPS position and a waypoint. A waypoint is a collection of GPS information for a location. When you select a waypoint, the transceiver automatically calculates the distance and bearing from your current GPS information to the waypoint. This information is shown on the Distance and Bearing tab.
Update the radio profile with a USB thumb drive Update the radio profile with a USB thumb drive CAUTION: An unconfigured radio is not capable of making calls. The 6110-MP can be configured in the field using data stored on a USB drive supplied by your Radio Network Administrator. The drive can be pre-loaded with a radio configuration profile, a set of encryption keys and software updates. To update or configure the radio: 1.
Update the radio profile with a USB thumb drive 6. Once the profile has been programmed into the radio, you may be asked to restart, press Sentry-H 6110-MP Operator Guide (Yes) to restart.
Troubleshooting Troubleshooting General Troubleshooting Below is a checklist for basic troubleshooting.
Troubleshooting Problem Solution GPS is not working Ensure that the front panel of the radio, and hence the GPS antenna, is facing the sky so that it can receive signals from satellites. Alternatively, connect a GPS antenna to the GPS port (J4) and place the antenna so that it is facing the sky. The 3G ALE link The tune time is not set to the same value in all radios, or it is not set to works in one direction the recommended time for the tuner.
Troubleshooting Error message Resolution Call type X not valid for Y call system You are attempting to create a contact or call a call type that is not compatible with the call system selected. Call type is not allowed This call type has been restricted on your radio. Call type is not allowed and has been replaced The call type you have selected for this with 'Prompt' contact is not available, the contact will prompt you to select a call type when selected.
Troubleshooting Error message Resolution Link lost, unable to send message The data link to the remote station was lost. Check your antenna, re-tune (if using the internal tuner) and re-position if possible and try again. Maximum number of users connected No more than 4 control points can be connected to the radio simultaneously. Message required Blank text messages cannot be sent. Messages require at least 1 character.
Troubleshooting Error message Resolution Record voice message timeout The Voice Message screen has timed out. You will need to re-record your message RM50 module not detected. Proceed anyway? The radio does not detect an RM50 module. This may affect the outcome of the requested action. RM50 power on failed The RM50 module has failed to start up. Digital Voice, 2G/3G ALE data, and security is not available on this radio.
Troubleshooting Error message Resolution Timeout The current action has timed out. Try again TOD Broadcast' is not allowed Transceiver is not the TOD Master for HF Network ... This radio is not the Time of Day master of the current HF network. Only the master can broadcast the TOD to network members.
Definitions Definitions Standards and icons Icon Description Note the text may be of interest to you CAUTION proceed with caution as your actions may lead to loss of data, privacy or signal quality WARNING your actions may cause harm to yourself or the equipment Acronyms and abbreviations This term… Means… AES advanced encryption standard ALE automatic link establishment CALM Codan automated link management CP Control Point DC direct current ESN electronic serial number GPS global posi
Definitions This term… Means… Rx receive, received SMS short message service SWR standing wave ratio USB Universal Serial Bus Glossary address The HF radio equivalent of a telephone number. Your station self address is used by other stations to call you, and it is sent when you make calls to identify you as the caller. It is sometimes referred to as an address or a self ID. Alert call A call that enables you to trigger an alert tone at a specific station then speak to an operator there.
Definitions handset A held-held device that is used to control the functions of a radio. It most commonly consists of an earpiece, microphone and PTT button. A handset may also have a display and a keypad. HF network The part of the radio configuration that defines specific details for making calls using Codan Selcall, 2G ALE or 3G ALE. macro A set of instructions to automate a task you perform with the radio. When a macro is assigned to a key, the key can be used to execute the task quickly.
Menu Navigation Menu Navigation Menu Map Scan Tables Sentry-H 6110-MP Operator Guide Page 65
www.codancomms.com ASIA PACIFIC (Head Office) Codan Limited 2 Second Avenue Technology Park Mawson Lakes SA 5095 AUSTRALIA T: +61 8 8305 0311 F: +61 8 8305 0411 E: support@codancomms.
