User's Manual

ManualsBrandsCodan ManualsElectronics2210 HF Radio System

RADIO COMMUNICATIONS

Getting Started Guide

Envoy™ Transceiver

Summary of content (147 pages)

PAGE 1
RADIO COMMUNICATIONS Envoy™ Transceiver Getting Started Guide
PAGE 2
No part of this manual may be reproduced, transcribed, translated into any language or transmitted in any form whatsoever without the prior written consent of Codan Limited. © Copyright 2012–2013 Codan Limited. Codan part number 15-04177-EN Issue 3, June 2013. CODAN™, Envoy™, Easitalk™, and CALM™ are trademarks of Codan Limited. Other brand, product, and company names mentioned in this document are trademarks or registered trademarks of their respective holders.
PAGE 3
TABLE OF CONTENTS Table of contents Section 1 Introduction Overview of this guide . The 2220 Handset . . . The 2221 Handset . . . The 2230 Desk Console Keypad . . . . . . . . . Accessing the CD . . . . Standards and icons . . . Section 2 Section 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
TABLE OF CONTENTS Advanced view . . . . . . . . . . . . . . . Switching between basic and advanced views Finding a word or value . . . . . . . . . . . . . Selecting an icon . . . . . . . . . . . . . . . . . Selecting a function from the menu bar . . . . . Entering text in a field . . . . . . . . . . . . . . Entering special characters . . . . . . . . . Entering text in the 2221 Handset . . . . . . Selecting a value from a list . . . . . . . . . . . Selecting/deselecting a check box . . . . . . . .
PAGE 5
TABLE OF CONTENTS Making a call from the Emergency key . . . . Using GPS . . . . . . . . . . . . . . . . . . . . . Viewing GPS information . . . . . . . . . . . Using encryption . . . . . . . . . . . . . . . . . . Switching the encryptor on or off . . . . . . . . Selecting a secure key . . . . . . . . . . . . . Adding a secure key . . . . . . . . . . . . . . Selecting the data rate . . . . . . . . . . . . . . Using a crosspatch . . . . . . . . . . . . . . . . . Overview of the 3031 Crosspatch . . . . . . .
PAGE 6
TABLE OF CONTENTS Appendix B Compliance Overview . . . . . . . . . . . . . . . . . . . . . . . . . . European R&TTE Directive . . . . . . . . . . . . . . . . Product marking and labelling . . . . . . . . . . . . . Radiation safety (EU installations only) . . . . . . . . Declaration of Conformity and Notified Body Letter of Opinion . . . . . . . . . . . . . . . . . . . . . . . . . Protection of the radio spectrum . . . . . . . . . . . . EMC and safety notices . . . . . . . . . . . . . . . . . .
PAGE 7
LIST OF FIGURES List of figures Figure 1: Figure 2: Figure 3: Figure 4: Figure 5: Figure 6: Figure 7: Figure 8: Figure 9: Figure 10: Figure 11: Figure 12: Figure 13: Figure 14: Figure 15: Figure 16: Figure 17: Figure 18: Figure 19: Figure 20: Figure 21: Figure 22: Figure 23: Figure 24: 2220 Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2221 Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2230 Desk Console . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
LIST OF FIGURES Figure 25: Figure 26: Figure 27: Figure 28: vi Crosspatch status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Call Log, Call History and Last Heard Log . . . . . . . 102 Typical mobile station . . . . . . . . . . . . . . . . . . . . . . . . 109 Typical fixed station . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 9
LIST OF TABLES List of tables Table 1: Table 2: Table 3: Table 4: Table 5: Table 6: Table 7: Keys and their function . . . . . . . . . . . . . . . . . . . . . . . . 8 Character-entry mode . . . . . . . . . . . . . . . . . . . . . . . . 45 GPS information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Cables for a typical mobile Envoy™ station . . . . . . 110 Cables for a typical fixed Envoy™ station . . . . . . .
PAGE 10
LIST OF TABLES This page has been left blank intentionally.
PAGE 11
1 Introduction Congratulations on choosing a Codan Envoy™ Transceiver to meet your HF communications needs. You can expect many years of reliable high performance, and if ever assistance is required, Codan’s world-class after-sales support team is ready to help. Please read this guide thoroughly and retain it for future reference. There is an index at the end of this guide to assist you in finding information.
PAGE 12
INTRODUCTION OVERVIEW OF THIS GUIDE Adding a contact—describes how to add a contact Specifications—provides a list of specifications for the transceiver Installing the transceiver—describes how to mount and connect the transceiver in mobile and fixed stations Compliance—provides mandatory compliance information 2 ENVOY™ TRANSCEIVER GETTING STARTED GUIDE
PAGE 13
INTRODUCTION THE 2220 HANDSET The 2220 Handset The 2220 Handset is a control point for the Envoy™ Transceiver. The user interface provides an icon-based menu structure for easy setup and operation of the transceiver.
PAGE 14
INTRODUCTION THE 2220 HANDSET The 2220 Handset is shipped from the factory with standard functions pre-programmed to specific keys. The standard function is written on the key in blue text. New user-defined functions may be assigned to most of the keys.
PAGE 15
INTRODUCTION THE 2221 HANDSET The 2221 Handset The 2221 Handset is a control point for the Envoy™ Transceiver. The user interface provides an icon-based menu structure for easy operation of the transceiver. It has a condensed set of keys for use in simpler communication scenarios.
PAGE 16
INTRODUCTION THE 2221 HANDSET The 2221 Handset is shipped from the factory with standard functions pre-programmed on the key, or in a list that is accessed via the Functions icon ( ). New user-defined functions may be assigned to this list.
PAGE 17
INTRODUCTION THE 2230 DESK CONSOLE The 2230 Desk Console The 2230 Desk Console is a control point for the Envoy™ Transceiver. The user interface provides an icon-based menu structure for easy setup and operation of the transceiver. The desk console is standard for a fixed station.
PAGE 18
INTRODUCTION KEYPAD Keypad Standard macros are programmed in the transceiver in the factory. You can also create a macro and assign it to a hot key. NOTE: Table 1: Key For more information, see the Reference Manual. Keys and their function Function Switches on the transceiver. Switches off the transceiver (hold for 2 sec).
PAGE 19
INTRODUCTION KEYPAD Table 1: Key Keys and their function (cont.) Function Scrolls down in a list of entries. Moves the highlight down a row. OK Enters the submenu or list of entries represented by the selected icon. Toggles the selection of a check box. Enters the virtual keypad in the user interface of a 2221 Handset. CALL Starts the calling process by jumping to the call screen (default behaviour). Jumps to Contacts/Call History/Emergency Contacts/Last Heard Log (hold for 2 sec).
PAGE 20
INTRODUCTION KEYPAD Table 1: Keys and their function (cont.) Key Function 7 V/S Enters 7, p, q, r, s, P, Q, R, S in character-entry mode. Toggles the type of mute selected. 8 SEC Enters 8, t, u, v, T, U, V in character-entry mode. Toggles secure mode on and off. Enables you to enter a PIN for a secure session, or access secure information (hold for 2 sec). 9 Enters 9, w, x, y, W, X, Y in character-entry mode. 0 VIEW Enters 0 or a space in character-entry mode.
PAGE 21
INTRODUCTION ACCESSING THE CD Accessing the CD To access the CD: Place the CD in the CD drive of your computer. You can view and search the Reference Manual and Getting Started Guide using the Adobe® Reader® supplied on the CD.
PAGE 22
INTRODUCTION STANDARDS AND ICONS Standards and icons The following standards and icons are used: This typeface... Means...
PAGE 23
2 Using the wizard This section contains the following topics: • Overview of the wizard on page 14 • Using the wizard on page 16 • Selecting a language on page 17 • Setting the time and date on page 17 • Setting the location of the desk console on page 18 • Adding a channel on page 19 • Entering a self address on page 21 • Adding a contact on page 22 • Selecting an antenna on page 29 • Selecting a peripheral device on page 30 ENVOY™ TRANSCEIVER GETTING STARTED GUIDE 13
PAGE 24
USING THE WIZARD OVERVIEW OF THE WIZARD Overview of the wizard The wizard is available if the transceiver: • has not been programmed with a profile • has a basic profile that has a common self address for the default HF networks Selcall and CALM, and has one scan table The wizard steps you through setting up information in the transceiver so that it may be operated at a basic level.
PAGE 25
USING THE WIZARD OVERVIEW OF THE WIZARD Figure 4: Steps in the wizard ENVOY™ TRANSCEIVER GETTING STARTED GUIDE 15
PAGE 26
USING THE WIZARD USING THE WIZARD Using the wizard The wizard should start automatically when a new transceiver is powered up for the first time. Figure 5: Wizard Startup screen NOTE: If the wizard screen doesn’t launch automatically, follow the instructions below. If your transceiver has been profiled using TPS, the wizard may not be available. NOTE: For information on specific entries in the wizard, please see the Reference Manual.
PAGE 27
USING THE WIZARD USING THE WIZARD Press wizard. (Yes) to confirm that you want to start the If you want to bypass the wizard, press (No). Selecting a language NOTE: This step in the wizard is shown if you have multiple languages available. To select a language: Press or to scroll to the language that you want to use on the control point, then press OK. Press Press (Yes) to confirm that you want to change the language. (Save) to save the information.
PAGE 28
USING THE WIZARD USING THE WIZARD Press press Repeat this for the day/month and year, as required. Press Press Press Press to move to the Time Format entry. Press or Press to move to the Date Format entry. Press or If you want to review the information that you have entered, press or to move through the entries. Press or to scroll to the value that you want to set, then to move to the next item. (Save) to save the local date. to move to the Clock entry.
PAGE 29
USING THE WIZARD USING THE WIZARD Adding a channel NOTE: This step in the wizard is shown if you are permitted to add channels. To add a channel: Press Enter the name that you want to use for the channel. Press Enter the transmit frequency (in kHz) that you want to use for this channel. Press (Yes) to add a channel, if required. to move to the Tx entry. to move to the Rx entry. The Rx entry is automatically filled with the transmit frequency.
PAGE 30
USING THE WIZARD USING THE WIZARD Do one of the following: • If you want to add another channel, press (Yes), then repeat these steps. • If you do not want to add another channel, press (No). The channels that you enter may be notionally grouped into scan tables. A scan table enables you to manage how these channels are scanned using one set of properties. The same channel may be included in one or more scan tables. One or more scan tables may be allocated to an HF network.
PAGE 31
USING THE WIZARD USING THE WIZARD Press Continue from Entering a self address on page 21. (Save) to add these channel selections. Entering a self address A self address is used by other stations to call your station. For example, if the self address of your station is 1234, operators at other stations enter the address 1234 when they want to make a call to you. To enter a self address: Enter the address that you want to use. You can enter up to six digits.
PAGE 32
USING THE WIZARD USING THE WIZARD Adding a contact A contact is a person who you want to call, and for whom you want to pre-define the method of calling them. You may be able to contact the same person via a number of different methods. When you set up the contact, you define each method as a separate call for the contact. NOTE: If you require more detail on adding a contact, see Contacts on page 93. To add a contact: Enter the name that you want to use for the contact, then press (Add Call).
PAGE 33
USING THE WIZARD USING THE WIZARD Adding a simple call A simple call is a call that requires an address only at this stage of the definition process. To continue with adding a Selective, Channel Test, Emergency, Get Position or Send Position call: Press Enter the address of the station that you want to call. Continue from Completing the contact on page 28. to move to the Selcall|ALE Address entry.
PAGE 34
USING THE WIZARD USING THE WIZARD Adding a Message call To continue with adding a Message call: Press Enter the address of the station that you want to call. Press If you want to enter a message: • to move to the Selcall|ALE Address entry. to move to the Message entry, then press Start typing the message. NOTE: • 24 . Press press Press OK to start a new line, if required. (Options), scroll to OK, then (Select) to add the message to the call.
PAGE 35
USING THE WIZARD USING THE WIZARD If you want to select a message from a list of stored messages: (Options), scroll to Stored, then (Select). • Press press • Press or to use. to scroll to the message that you want NOTE: If you want to view the message, press (Details) to view the message, then press (Close). • Press OK to select the message. • Edit the message, if required. • Press press (Options), scroll to OK, then (Select). Continue from Completing the contact on page 28.
PAGE 36
USING THE WIZARD USING THE WIZARD Adding a Phone call To continue with adding a Phone call: 26 Press Enter the phone number. Continue from Completing the contact on page 28. to move to the Phone Number entry.
PAGE 37
USING THE WIZARD USING THE WIZARD Adding a Get Status call To continue with adding a Get Status call: Press Enter the address of the station that you want to call. Press to move to the Selcall|ALE Address entry. to move to the Status Type entry, then press Selcall HF network . ALE/CALM HF network ALE Site Manager: Auto Manual Restricted Press or to scroll to the status type that you want to use, then press OK.
PAGE 38
USING THE WIZARD USING THE WIZARD Completing the contact To finish entering the information required for the contact: Press to move to the Call Description entry. By default, the call type is entered as the call description. Enter the description that you want to use for this call. Press If you want to add another call for the contact, press (Yes), then repeat the steps for adding a call. (Save) to save the information.
PAGE 39
USING THE WIZARD USING THE WIZARD Selecting an antenna Each type of antenna has a specific requirement for tuning, and the transceiver uses a different protocol for each one. You must select the type of antenna that is used in your station so that the transceiver knows how to tune the antenna. Some antennas, such as broadband antennas, do not require tuning. To select an antenna: Do one of the following: • Press or to scroll to the antenna type that you want to use, then press OK.
PAGE 40
USING THE WIZARD USING THE WIZARD Selecting a peripheral device When you select the peripheral device from the list, the transceiver automatically sets these properties. NOTE: Codan peripheral devices are listed by their type number, for example, 3031 Crosspatch. The type number for a Codan device is located on the front or serial number escutcheon. To select a peripheral device: Press or to scroll to the type of peripheral device that is attached to the connector, then press OK.
PAGE 41
3 Navigating the menu structure This section contains the following topics: • The basic menu structure on page 32 • Navigating the menu structure on page 34 • Overview of basic and advanced views on page 36 • Finding a word or value on page 38 • Selecting an icon on page 41 • Selecting a function from the menu bar on page 42 • Entering text in a field on page 44 • Selecting a value from a list on page 49 • Selecting/deselecting a check box on page 50 • Moving a slider on page 51 • Chan
PAGE 42
NAVIGATING THE MENU STRUCTURE THE BASIC MENU STRUCTURE The basic menu structure The menu structure comprises a main menu and a series of submenus that are accessed via the main menu. Each menu and submenu is represented by an icon. Some icons provide direct access to an input/view screen, while other icons provide a list of entries for the menu.
PAGE 43
NAVIGATING THE MENU STRUCTURE THE BASIC MENU STRUCTURE Figure 7: Menu structure (user level, basic view) Setup Wizard Add Channel User Data Channels Scan Tables HF Networks Contacts Messages Modes Peripherals Settings Control Point Configuration Connectors Scan Calling GPS Admin Login/Logout Advanced View Information Device Information Option Password Version IP Connectivity Licence General Time and Date Secure Brightness Self Tests Find RFU GPS Functions (2221 only) The menu items may contain f
PAGE 44
NAVIGATING THE MENU STRUCTURE NAVIGATING THE MENU STRUCTURE Navigating the menu structure The menu structure comprises a main menu and a series of submenus that are accessed via the main menu. Navigation keys enable you to highlight an icon, then press OK to select that menu. You can continue drilling down through the menu structure in this way. At the lowest level of the menu structure there is either an input/view screen, or a list of entries.
PAGE 45
NAVIGATING THE MENU STRUCTURE NAVIGATING THE MENU STRUCTURE To go to the top level in the menu structure, do one of the following: • Press PTT to exit to the channel screen, then press (Menu) to enter the top level of the menu structure. • Press to return to the top level of the menu structure, one level at a time.
PAGE 46
NAVIGATING THE MENU STRUCTURE OVERVIEW OF BASIC AND ADVANCED VIEWS Overview of basic and advanced views There are two views of information in the user interface of the control point: basic and advanced. The contents of basic and advanced views are pre-determined and cannot be changed. Basic view Basic view provides a condensed view of the user interface, and typically the view at which the control point is operated. When you power up the transceiver, the control point enters basic view.
PAGE 47
NAVIGATING THE MENU STRUCTURE OVERVIEW OF BASIC AND ADVANCED VIEWS Figure 10: Advanced view advanced view indicator Switching between basic and advanced views The user can switch between basic and advanced views to either: • simplify the user interface of the control point (basic view), or • access advanced settings that they are permitted to change (advanced view) To switch between views: Press From the main menu, select Press OK to toggle advanced view on or off as required.
PAGE 48
NAVIGATING THE MENU STRUCTURE FINDING A WORD OR VALUE Finding a word or value The quickest way to find an entry or a value in the user interface of the control point is to use the Find function, which is available via the key when the icon selected contains submenus or lists of entries. The feature searches for the sequence of characters (letter, numbers, or a combination of both) that you enter.
PAGE 49
NAVIGATING THE MENU STRUCTURE FINDING A WORD OR VALUE Figure 11: Find function To find a word or value: Highlight the icon that represents the highest level in which you want to search, then press (Find).
PAGE 50
NAVIGATING THE MENU STRUCTURE FINDING A WORD OR VALUE NOTE: If you select the icon by pressing OK, you will enter that menu level. If you do not want to search at the lower level, press (Close) to return to the higher level, then press (Find) again. Enter the letter and/or number on which you want to search. Any entries or values that contain the character you have entered are shown in a list, with the character highlighted. NOTE: You may have to scroll through the list to view all of the results.
PAGE 51
NAVIGATING THE MENU STRUCTURE SELECTING AN ICON Selecting an icon The top levels of the menu structure are represented by icons. In order to enter the menu represented by the icon, you need to select the icon. Figure 12: Highlighted icon highlighted icon To select an icon: Use , select. Press OK or , and ENVOY™ TRANSCEIVER GETTING STARTED GUIDE to highlight the icon that you want to (OK) to select the icon.
PAGE 52
NAVIGATING THE MENU STRUCTURE SELECTING A FUNCTION FROM THE MENU BAR Selecting a function from the menu bar The menu bar at the bottom of the screen provides varying functions, depending on the context. You can select a function directly, or activate a pop-up from the menu bar by pressing the corresponding key ( or ). A vertical line next to the text indicates that there are a number of choices from which to choose.
PAGE 53
NAVIGATING THE MENU STRUCTURE SELECTING A FUNCTION FROM THE MENU BAR If a pop-up of available functions is shown: • Press or to select. • Press to scroll to the function that you want (Select). The function is performed.
PAGE 54
NAVIGATING THE MENU STRUCTURE ENTERING TEXT IN A FIELD Entering text in a field You may need to enter text into a field within an entry. This may be a name given to some user data, or it may be a specific value, such as a frequency. When you first enter an editable text field, either by selecting a menu or using the and navigation keys, any existing text that you can edit is highlighted. You can use this text, edit this text, or delete this text and enter new text.
PAGE 55
NAVIGATING THE MENU STRUCTURE ENTERING TEXT IN A FIELD Figure 15: Character-entry mode indicator character-entry mode indicator Table 2: Character-entry mode Character-entry mode Indicat or All upper-case letters All lower-case letters Leading-capital letters Numbers ENVOY™ TRANSCEIVER GETTING STARTED GUIDE 45
PAGE 56
NAVIGATING THE MENU STRUCTURE ENTERING TEXT IN A FIELD Do any of the following: • Press or to move the cursor to the point at which you want to enter text. • Press to delete text to the left of the cursor. • Hold to delete the whole entry. • Press the key on the keypad that corresponds to the letter that you want to enter. For example, if you want to enter the letter E, press 3 twice. After a brief pause, the cursor moves to the next space, ready to enter another character.
PAGE 57
NAVIGATING THE MENU STRUCTURE ENTERING TEXT IN A FIELD Depending on the context, you can select from: Press , , or to highlight the character that you want to use, then press (Insert). Repeat as required. Entering text in the 2221 Handset The 2221 Handset does not have alphanumeric keys, however, you can still enter text into fields within the user interface. CAUTION: This process describes how to enter text into an entry field using the virtual keypad, then save the text back to the entry.
PAGE 58
NAVIGATING THE MENU STRUCTURE ENTERING TEXT IN A FIELD Press , , or to move the highlight to the character that you want to select, then press OK. If you want to change case, enter a number, or enter a special character, scroll to , then press OK. Continue entering text in this manner. Press (Save) to save the information. You are returned to the entry.
PAGE 59
NAVIGATING THE MENU STRUCTURE SELECTING A VALUE FROM A LIST Selecting a value from a list When you select an entry that has a list of values, either by selecting an icon or using the and navigation keys, the field is highlighted to show that it can be edited, and / indicators appear on one or both sides of the field to show that multiple values are available.
PAGE 60
NAVIGATING THE MENU STRUCTURE SELECTING/DESELECTING A CHECK BOX Selecting/deselecting a check box There are some entries in the menu structure that require you to enable or disable a particular feature via a check box. When the check box contains a , the feature is enabled. If the check box is clear, the feature is disabled. Figure 17: Entry with a check box To select or deselect a check box: Highlight the entry. Press OK to toggle the check box as selected or deselected.
PAGE 61
NAVIGATING THE MENU STRUCTURE MOVING A SLIDER Moving a slider Some values in the user interface of the control point are represented by a slider. Figure 18: A slider value slider navigation key indicator To move a slider: Press any of the navigation keys suggested in the navigation key indicator to adjust the slider.
PAGE 62
NAVIGATING THE MENU STRUCTURE CHANGING THE ORDER OF ITEMS IN A LIST Changing the order of items in a list In some areas of the control point, you are able to change the order in which the items appear, which impacts how the item is viewed, or when each item may be used. For example, you may change the order in which the channels, scan tables, HF networks, contacts, phone links, and NETs are listed so that you don’t have to scroll to the item to select it.
PAGE 63
NAVIGATING THE MENU STRUCTURE SAVING YOUR CHANGES Saving your changes When information in an entry has been changed, either by editing existing text or selecting a different value from a list, an asterisk is added to the title of the screen. Figure 19: Screen that has changes to be saved asterisk indicates that changes have been made To save changes: Do one of the following: • Press (Save). • Press press (Options), scroll to Save, then (Select). • Press (Close) to discard the changes.
PAGE 64
NAVIGATING THE MENU STRUCTURE SAVING YOUR CHANGES This page has been left blank intentionally.
PAGE 65
4 Structure of information This section contains the following topics: • Structure of user information on page 56 • Structure of contact and call information on page 58 ENVOY™ TRANSCEIVER GETTING STARTED GUIDE 55
PAGE 66
STRUCTURE OF INFORMATION STRUCTURE OF USER INFORMATION Structure of user information Information in the Envoy™ Transceiver is stored like blocks in a building. Basic blocks are populated with information first, then these blocks, along with different blocks, are assembled into larger blocks. Ultimately, one of the top-level blocks is used to make a call. The most basic block is a frequency. A frequency is combined with a mode, say USB or LSB, and a name to become a channel.
PAGE 67
STRUCTURE OF INFORMATION STRUCTURE OF USER INFORMATION Figure 20: Basic structure of information in the Envoy™ Transceiver Channels Scan table 1 Selected channels HF network Call system (RFDS) Self address Selected scan tables Scan table 2 Selected channels HF network Call system (ALE) Self address Selected scan tables HF network Call system (Selcall) Self address Global (all channels) ENVOY™ TRANSCEIVER GETTING STARTED GUIDE 57
PAGE 68
STRUCTURE OF INFORMATION STRUCTURE OF CONTACT AND CALL INFORMATION Structure of contact and call information A contact holds information on calls that you make to a particular person. You may have several methods of calling the same person. Each method that you use is bundled into a call for that contact.
PAGE 69
5 Operating the transceiver This section contains the following topics: • Switching the transceiver on and off on page 60 • The channel screen on page 61 • Scanning channels on page 65 • Muting the transceiver on page 67 • Using the microphone on page 68 • Setting the basics on page 69 • Calling on page 71 • Using GPS on page 79 • Using encryption on page 81 • Using a crosspatch on page 88 • Upgrading the transceiver via a USB stick on page 91 ENVOY™ TRANSCEIVER GETTING STARTED GUIDE
PAGE 70
OPERATING THE TRANSCEIVER SWITCHING THE TRANSCEIVER ON AND OFF Switching the transceiver on and off Switching on the transceiver To switch on the transceiver: Press . The template screen, then the welcome screen (if set) are shown briefly, followed by the channel screen. Switching off the transceiver To switch off the transceiver: Hold for 2 sec, then release. The transceiver is switched off.
PAGE 71
OPERATING THE TRANSCEIVER THE CHANNEL SCREEN The channel screen The channel screen shows the following information: • the name of the currently selected channel • the transmit and receive frequencies, if applicable • a bar graph that indicates the signal strength on receive (green) and the output power on transmit (red) • the transmit power level setting • the call type icon (when calling) or the scan indicator (when scanning) • the mute type indicator • the mode ENVOY™ TRANSCEIVER GETTING ST
PAGE 72
OPERATING THE TRANSCEIVER THE CHANNEL SCREEN Figure 22: Channel screen signal strength indicator Tx power setting call type icon mute type indicator (highlighted when mute is on) Rx/Tx indicator mode title bar channel name Tx/Rx frequency status areas menu bar left software key right software key volume indicator If the transmit and receive frequencies are the same, the frequency is only shown on the right side of the screen.
PAGE 73
OPERATING THE TRANSCEIVER THE CHANNEL SCREEN Figure 23: Scanning screen scan indicator Selecting a channel To select a channel: Press PTT to exit to the channel or scanning screen. If the transceiver is scanning, press SCAN to switch off scanning. Press or to scroll to the channel that you want to use. The channel is selected. NOTE: If you want to change the sideband, press MODE. If the mode does not change, there is only one mode for the channel.
PAGE 74
OPERATING THE TRANSCEIVER THE CHANNEL SCREEN NOTE: 64 If you have an automatic antenna tuner fitted, press PTT to tune the antenna to the currently selected channel. Do any of the following: • Hold OK to edit the channel, if permitted. • Press OK to search for a channel. • Press CALL to start a call. • Hold CALL to go to Contacts.
PAGE 75
OPERATING THE TRANSCEIVER SCANNING CHANNELS Scanning channels If you intend to receive calls on several channels, switch on scanning. When scanning is switched on, the transceiver sequentially selects each channel/mode in your scan tables to detect incoming calls. The channel are scanned in a continuous cycle. Mute is switched on automatically. NOTE: Only those scan tables that are set to be scanned have the channels scanned.
PAGE 76
OPERATING THE TRANSCEIVER SCANNING CHANNELS NOTE: When scanning is switched on, mute is also switched on. NOTE: If you press PTT while the transceiver is scanning, the scan is stopped. Pausing scanning To pause scanning: Do one of the following: • To pause scanning on the last-selected channel, press OK. • To pause scanning and scroll to another channel, press or . The channel/modes through which you can scroll are those in the scan tables that are being scanned.
PAGE 77
OPERATING THE TRANSCEIVER MUTING THE TRANSCEIVER Muting the transceiver When the transceiver is set to a channel or is scanning channels, and mute is switched off, you hear on-air signals on each channel. If you do not want to listen to this, you can silence the transceiver by switching mute on. You can set the mute to open when a voice signal is detected (Voice mute V), or only when a call addressed to your station is received (Selcall mute S).
PAGE 78
OPERATING THE TRANSCEIVER USING THE MICROPHONE Using the microphone The microphone is located at the top centre of your handset. When you talk into the microphone: • hold the microphone side-on and close to your mouth • hold down PTT • speak clearly at your normal volume and rate • release PTT to return to receiving mode NOTE: By default, the transceiver is set up to transmit a short beep when you release PTT. This removes the need for you to say ‘over’ at the end of your transmission.
PAGE 79
OPERATING THE TRANSCEIVER SETTING THE BASICS Setting the basics Setting the date and time The transceiver is set to UTC time in the factory. You set the local time and time zone offset for the location of the control point. This feature is useful if you have a communication network that spreads over several time zones, or you need to time stamp your transmissions according to the current time at longitude zero. To set the time and date: From the main menu, select and Date).
PAGE 80
OPERATING THE TRANSCEIVER SETTING THE BASICS Press to move to the Time Format entry. Press or Press to move to the Date Format entry. Press or If you want to review the information that you have entered, press or to move through the entries. Press to select the format that you want to use. to select the format that you want to use. (Save) to save the information. Setting the brightness of the display To set the brightness: 70 Do one of the following: + 0.
PAGE 81
OPERATING THE TRANSCEIVER CALLING Calling This section describes how to make the various types of calls from the transceiver. Figure 24: Call screen navigation indicator call type HF network address incoming call outgoing call select HF network NOTE: Additional call types are discussed in the Reference Manual. Making a Selective call If you want to speak with the operator at a particular station, make a Selective call to the address of that station.
PAGE 82
OPERATING THE TRANSCEIVER CALLING If you do not want to use the HF network shown at the top right of the screen: • Press (Options). • Scroll to HF Networks, then press • Scroll to the HF network that you want to use, then press OK. Press or selected. Do one of the following: (Select). to select the Selective call type if it is not • To repeat the call to the last address used, press CALL. • To call a different station, enter the address, then press CALL.
PAGE 83
OPERATING THE TRANSCEIVER CALLING Making a Message call If you want to send a text message to another station, make a Message call. You can: • enter a message at the time that you make a call • store up to 10 messages in User Data > Messages for later use • store messages in a contact as part of a pre-programmed Message call To make a Message call: Press CALL. The call type and address of the last call are shown at the top of the call screen.
PAGE 84
OPERATING THE TRANSCEIVER CALLING 74 Do one of the following: • To repeat the call to the last address used, press CALL. • To call a different station, enter the address, then press CALL. • To repeat or return a call from the call log, press to scroll to the call, then press CALL.
PAGE 85
OPERATING THE TRANSCEIVER CALLING If you want to enter a message: • Start typing the message. NOTE: • Press press Press OK to start a new line, if required. (Options), scroll to OK, then (Select) to add the message to the call. If you want to select a message from a list of stored messages: (Options), scroll to Stored, then (Select). • Press press • Press or to use.
PAGE 86
OPERATING THE TRANSCEIVER CALLING • (Options), scroll to OK, then (Select). Press press If prompted, press or to scroll to the channel that you want to use, then press CALL. A is shown next to the currently selected channel/mode. To abort the call before it is answered, press PTT or SCAN. There will be audible beeps or a pop-up message to indicate that the call has been successful. Making a call to a contact To make a call to a contact: Hold CALL. Press If required, press to make.
PAGE 87
OPERATING THE TRANSCEIVER CALLING If prompted, press or to scroll to the channel that you want to use, then press CALL. A is shown next to the currently selected channel/mode. To abort the call before it is answered, press PTT or SCAN. There will be audible beeps or a pop-up message to indicate that the call has been successful. Making a call from the Call History The Envoy™ Transceiver stores information on the calls that you send and receive.
PAGE 88
OPERATING THE TRANSCEIVER CALLING Press CALL. Press Continue from making your chosen call type. or to select the call type that you want to use. Making a call from the Emergency key You can set up emergency contacts with calls that are chained together when you hold the key. CAUTION: If you have more than one emergency contact, you will be prompted to select the emergency contact that you want to call at the time of the call. NOTE: For more information, see the Reference Manual.
PAGE 89
OPERATING THE TRANSCEIVER USING GPS Using GPS Viewing GPS information NOTE: You can view GPS information if the GPS Call option is installed. To view GPS information: Table 3: From the main menu, select Press (General), then (GPS). to move to the tab that you want to view. GPS information Tab Description Latitude and longitude readings from a GPS receiver, or from Settings > GPS > My Position. Altitude and speed readings are hidden by default.
PAGE 90
OPERATING THE TRANSCEIVER USING GPS Table 3: GPS information (cont.) Tab Description Signal strength from each visible satellite. The number represents a particular satellite, and its location is shown on the Satellites Constellation tab. Satellites with a blue signal strength provide information for the GPS location. Map of visible satellites. The satellites that are coloured blue are providing the strongest signals and this information is being used to establish the position of the receiver.
PAGE 91
OPERATING THE TRANSCEIVER USING ENCRYPTION Using encryption Switching the encryptor on or off The 2220 Handset and 2230 Desk Console have hot keys that access the secure feature directly. With the 2221 Handset, you access the secure feature via Functions. If you want secure to remain on at all times, you set this in Settings > Security > Secure Start State. NOTE: For more information, see the Reference Manual.
PAGE 92
OPERATING THE TRANSCEIVER USING ENCRYPTION For CES-128 voice encryption you will see: Secure Clear For AES-256 digital voice encryption you will see: Secure Clear For AES-256 digital data encryption you will see: Secure 82 Clear ENVOY™ TRANSCEIVER GETTING STARTED GUIDE
PAGE 93
OPERATING THE TRANSCEIVER USING ENCRYPTION Change to the encryptor type that you want to use, if permitted. If you are using CES-128 voice encryption with a 2220 Handset or 2230 Desk Console, press to go to secure standby mode, if enabled and required. Standby If you are using CES-128 voice encryption with a 2221 Handset, do the following to go to secure standby mode: • Press • Press • Press (Options). or ENVOY™ TRANSCEIVER GETTING STARTED GUIDE to scroll to the Standby On option.
PAGE 94
OPERATING THE TRANSCEIVER USING ENCRYPTION Selecting a secure key If an encryptor contains two or more keys, you have the option of selecting a different key for encryption, if permitted. When AES-256 digital voice and data encryptors are used together, the selected key is common to both. To select a secure key: If you are using a 2220 Handset or 2230 Desk Console, do one of the following: • From the main menu, select (Secure). • Hold SEC.
PAGE 95
OPERATING THE TRANSCEIVER USING ENCRYPTION Adding a secure key If you are permitted to add a secure key for a CES-128 or AES-256 encryptor, the transceiver automatically selects the next empty secure index into which you can enter a secure key. You cannot select the secure key index. To add a secure key: If you are using a 2220 Handset or 2230 Desk Console, do one of the following: • From the main menu, select (Secure). • Hold SEC.
PAGE 96
OPERATING THE TRANSCEIVER USING ENCRYPTION Enter the characters that you want to use for the secure key. Press (Save) to save the information. Press (Close). Selecting the data rate The data rate affects the speed with which digitally encrypted transmissions are sent. To select a different data rate: 86 If you are using a 2220 Handset or 2230 Desk Console, do one of the following: • From the main menu, select (Secure). • Hold SEC.
PAGE 97
OPERATING THE TRANSCEIVER USING ENCRYPTION Press Press or to select the data rate that you want to use. (OK).
PAGE 98
OPERATING THE TRANSCEIVER USING A CROSSPATCH Using a crosspatch Overview of the 3031 Crosspatch The 3031 Crosspatch is a device that connects an HF communication system with a VHF or UHF communication system. NOTE: For details on installing the crosspatch and its operation, see the documentation provided with the device. NOTE: You must select the 3031 Crosspatch as the peripheral device for the 15-way connector.
PAGE 99
OPERATING THE TRANSCEIVER USING A CROSSPATCH Figure 25: Crosspatch status crosspatch indicator Off crosspatch state crosspatch indicator Active crosspatch state crosspatch indicator Standby crosspatch state ENVOY™ TRANSCEIVER GETTING STARTED GUIDE 89
PAGE 100
OPERATING THE TRANSCEIVER USING A CROSSPATCH Changing the operating mode of the crosspatch To change the operating mode of the crosspatch: If you are using a 2220 Handset or 2230 Desk Console, press 5. If you are using a 2221 Handset: • From the main menu, select (Functions). • Press or to scroll to the Next Crosspatch State function. • Press (OK).
PAGE 101
OPERATING THE TRANSCEIVER UPGRADING THE TRANSCEIVER VIA A USB STICK Upgrading the transceiver via a USB stick Firmware packages, profiles from TPS, and secure keys may be loaded onto a USB stick, providing a portable method of upgrading transceivers in the field. You can also read a profile from a transceiver in the field. When the USB stick is connected to the control point, a selection menu is shown for various activities, depending on the values set in Settings > General > USB User Access.
PAGE 102
OPERATING THE TRANSCEIVER UPGRADING THE TRANSCEIVER VIA A USB STICK 92 Do one of the following: • Press or to scroll to the firmware package, profile, or key set file, press (Options), scroll to Open, then press (Select). • Press or to scroll to the folder in which you want to save the profile from the transceiver, then press (Save). Press (Yes) to confirm that you want to complete the selected action. Perform more tasks with the USB stick as required.
PAGE 103
6 Contacts This section contains the following topics: • Adding a contact on page 94 • Adding a contact from the Call Log, Call History, or Last Heard Log on page 102 ENVOY™ TRANSCEIVER GETTING STARTED GUIDE 93
PAGE 104
CONTACTS ADDING A CONTACT Adding a contact Contacts are used to pre-define the typical calls that you want to make to another person. For each contact you can define a number of calls.
PAGE 105
CONTACTS ADDING A CONTACT Enter the name that you want to use for the contact, then press (Add Call). The HF Network entry is highlighted. The HF network defines the call system and self address that is used by your station when the call is made. For example, if you want to select a channel for the call, use a Selcall HF network. If you want the transceiver to automatically select a channel for the call, use an ALE/CALM HF network.
PAGE 106
CONTACTS ADDING A CONTACT If you are adding: • a Selective, Channel Test, Emergency, Get Position or Send Position call, continue from Adding a simple call on page 96 • a Message call Adding a Message call on page 97 • a Phone call Adding a Phone call on page 98 • a Get Status call Adding a Get Status call on page 99 • an RFDS Emergency call Adding an RFDS Emergency call on page 100 Adding a simple call A simple call is a call that requires an address only at this stage of the definition proce
PAGE 107
CONTACTS ADDING A CONTACT Adding a Message call To continue with adding a Message call: Press Enter the address of the station that you want to call. Press If you want to enter a message: • to move to the Selcall|ALE Address entry. to move to the Message entry, then press Start typing the message. NOTE: • . Press press Press OK to start a new line, if required. (Options), scroll to OK, then (Select) to add the message to the call.
PAGE 108
CONTACTS ADDING A CONTACT • Press or to use. to scroll to the message that you want NOTE: If you want to view the message, press (Details) to view the message, then press (Close). • Press OK to select the message. • Edit the message, if required. • Press press (Options), scroll to OK, then (Select). Continue from Completing the contact on page 101. Adding a Phone call To continue with adding a Phone call: 98 Press to move to the Phone Number entry.
PAGE 109
CONTACTS ADDING A CONTACT Enter the phone number. Continue from Completing the contact on page 101. Adding a Get Status call To continue with adding a Get Status call: Press Enter the address of the station that you want to call. Press to move to the Selcall|ALE Address entry. to move to the Status Type entry, then press Selcall HF network . ALE/CALM HF network ALE Site Manager: Auto Manual Restricted Press or to scroll to the status type that you want to use, then press OK.
PAGE 110
CONTACTS ADDING A CONTACT Adding an RFDS Emergency call NOTE: RFDS Emergency calls are only available when an RFDS HF network is selected or you set the HF Network entry to Prompt. To continue with adding an RFDS Emergency call: 100 Continue from Completing the contact on page 101.
PAGE 111
CONTACTS ADDING A CONTACT Completing the contact To finish entering the information required for the contact: Press to move to the Call Description entry. By default, the call type is entered as the call description. Enter the description that you want to use for this call. Press If you want to add another call, press (Options), scroll to Add Call, press (Select), then repeat the steps for adding a call. Press (Options), scroll to Save, then press (Select).
PAGE 112
CONTACTS ADDING A CONTACT FROM THE CALL LOG, CALL HISTORY, OR LAST HEARD LOG Adding a contact from the Call Log, Call History, or Last Heard Log You can save information from the Call Log, Call History, or Last Heard Log to Contacts. This can either be a new call type for an existing contact, or you can add a new contact to hold this call information. The Call Log and Call History are separate entities, however, the process for saving the call information to a contact is the same.
PAGE 113
CONTACTS ADDING A CONTACT FROM THE CALL LOG, CALL HISTORY, OR LAST HEARD LOG To add a contact from the Call Log, Call History, or Last Heard Log: Do one of the following: • Press CALL, then press entry in the Call Log. • Hold CALL, press , then press the entry in the Call History. or to scroll to the or to scroll to Press (Options), scroll to Save, then press (Select).
PAGE 114
CONTACTS ADDING A CONTACT FROM THE CALL LOG, CALL HISTORY, OR LAST HEARD LOG This page has been left blank intentionally.
PAGE 115
7 Table 4: Specifications Specifications Item Specification Frequency range Transmit: 1.6 to 30 MHz Receive: 0.25 to 30 MHz Channel capacity (single or two-frequency simplex channels) X1: 100 (International) 400 (Australia) X2: 1000 Operating modes Single sideband (J3E) USB and LSB or switched USB/LSB, AM (A3E Rx, H3E Tx), CW (J1A, A1A) Environment Ambient temperature: í30 to +60°C (–22 to 140°F) Relative humidity: 95% Derate upper ambient temperature by 1°C (33.
PAGE 116
SPECIFICATIONS Table 4: Specifications (cont.) Item Specification Size 2210 RFU: 210 mm W × 270 mm D × 65 mm H (8.4 in W × 10.8 in D × 2.6 in H) 2220/2221 Handset: 74 mm W × 32 mm D × 150 mm H (2.9 in W × 1.3 in D × 5.9 in H) 2230 Desk Console: 190 mm W × 233 mm D × 81 mm H (7.5 in W × 9.2 in D × 3.2 in H) Handset and speaker connector: 42 mm W × 55 mm D × 22 mm H (1.7 in W × 2.2 in D × 0.9 in H) 2210 RFU: 2.8 kg (6.2 lb) 2220/2221 Handset: 0.3 kg (0.7 lb) 2230 Desk Console: 1 kg (2.
PAGE 117
A Installing the transceiver This section contains the following topics: • Overview of mobile stations on page 108 • Overview of fixed stations on page 114 ENVOY™ TRANSCEIVER GETTING STARTED GUIDE 107
PAGE 118
INSTALLING THE TRANSCEIVER OVERVIEW OF MOBILE STATIONS Overview of mobile stations A mobile station typically consists of a transceiver, a 12 V DC power supply (battery), an antenna, control and accessory devices, ancillary equipment, and appropriate connecting cables. The antenna is connected to the transceiver by coaxial cable. An automatic tuning antenna also requires a control cable connected to the transceiver.
PAGE 119
INSTALLING THE TRANSCEIVER OVERVIEW OF MOBILE STATIONS Figure 27: Typical mobile station l tro a enn ant nna e t an ry te bat con Un it ria l No Ty .
PAGE 120
INSTALLING THE TRANSCEIVER OVERVIEW OF MOBILE STATIONS Cables in a mobile station Table 5: Cables for a typical mobile Envoy™ station Cable Symbol Part number Handset and speaker connector1 08-06022-001 Coaxial cable between RFU and antenna2 08-01503-006 Control cable between RFU and antennab 08-05627-006 DC power supply cablea 08-03255 1. 2. The part number for the cable corresponds to a standard 6 m cable. The part number for the cable corresponds to a standard 6 m cable.
PAGE 121
INSTALLING THE TRANSCEIVER OVERVIEW OF MOBILE STATIONS Mounting the speaker To mount the speaker: Secure the mounting cradle to the surface with at least two screws. Ensure there is sufficient space at the rear for the cable. Attach the speaker to the cradle with the two screws and rubber washers. Mounting the handset and speaker connector To mount the handset and speaker connector: Use cable ties or screws to secure the handset and speaker connector in a suitable location.
PAGE 122
INSTALLING THE TRANSCEIVER OVERVIEW OF MOBILE STATIONS Connecting a mobile Envoy™ station NOTE: A typical mobile station is shown in Figure 27. To connect a mobile station: Connect the cable (Codan part number 08-06022-001) from the handset and speaker connector to the 10-way plug on the cable lead from the RFU, then secure the locking ring tightly into position.
PAGE 123
INSTALLING THE TRANSCEIVER OVERVIEW OF MOBILE STATIONS Connecting the power supply To connect the transceiver to the battery power supply: If you are using a 24 V battery supply, connect the battery to a 24 V to 12 V voltage regulator (Codan part number 15-00508). Connect the power supply cable (Codan part number 08-03255) to the plug at the end of the 12 V cable lead from the RFU.
PAGE 124
INSTALLING THE TRANSCEIVER OVERVIEW OF FIXED STATIONS Overview of fixed stations A fixed station typically consists of a transceiver, an AC transceiver supply connected directly to the mains, an antenna, control and accessory devices, ancillary equipment, and appropriate connecting cables. The transceiver is connected to the DC output lead of the transceiver supply. The antenna is connected to the transceiver by coaxial cable.
PAGE 125
INSTALLING THE TRANSCEIVER OVERVIEW OF FIXED STATIONS Figure 28: Typical fixed station tun x (opti er 0 0 ona l) 627 00x 5 0 08- 1503rol 08-0 5 ont 25 c -03 na 8 n 0 e bro ant nna a e antdban t n a ry enn d a te bat y wa r 15- ecto n con FU R ay 6-wector n con ™ RF Un it Se ria lN o.
PAGE 126
INSTALLING THE TRANSCEIVER OVERVIEW OF FIXED STATIONS Cables in a fixed station Table 6: Cables for a typical fixed Envoy™ station Cable Symbol Part number Cable between RFU and 2230 Desk Console 08-07205-xxx Handset and speaker connector1 and cable (optional) 08-06022-001 Coaxial cable between RFU and antenna2 08-01503-006 1. 2. The part number for the cable corresponds to a standard 6 m cable. The part number for the cable corresponds to a 30 m coaxial cable.
PAGE 127
INSTALLING THE TRANSCEIVER OVERVIEW OF FIXED STATIONS Rack-mounting unit A rack-mounting unit consists of a 19 inch rack tray. It can be used to mount your fixed station with either a desk console or the handset and cradle. Connecting a fixed Envoy™ station NOTE: A typical fixed station is shown in Figure 28.
PAGE 128
INSTALLING THE TRANSCEIVER OVERVIEW OF FIXED STATIONS Connect the plug at the end of the cable to the socket at the end of the cable lead from the RFU, then secure the locking ring tightly into position. Connect the plug at the opposite end of the cable to the socket located at the base of the antenna, then secure the locking ring tightly into position.
PAGE 129
INSTALLING THE TRANSCEIVER OVERVIEW OF FIXED STATIONS Connecting the transceiver supply To connect the transceiver to the transceiver supply: Connect the DC output from the transceiver supply to the plug at the end of the 12 V cable lead from the RFU. Connect the transceiver supply to the AC mains supply.
PAGE 130
INSTALLING THE TRANSCEIVER OVERVIEW OF FIXED STATIONS This page has been left blank intentionally.
PAGE 131
B Compliance This section contains the following topics: • Overview on page 122 • European R&TTE Directive on page 123 • EMC and safety notices on page 126 • FCC compliance on page 130 • IC certification on page 131 • RCM approval on page 132 ENVOY™ TRANSCEIVER GETTING STARTED GUIDE 121
PAGE 132
COMPLIANCE OVERVIEW Overview This section describes how to ensure the Envoy™ Transceiver complies with the European R&TTE Directive 1999/5/EC. This section also contains the requirements for RCM.
PAGE 133
COMPLIANCE EUROPEAN R&TTE DIRECTIVE European R&TTE Directive The Envoy™ Transceiver has been tested and complies with the following standards and requirements (articles of the R&TTE Directive): • Article 3.1b: ETSI EN 301 489-1 V1.8.1 • Article 3.1b: ETSI EN 301 489-15 V1.2.1 • Article 3.2: Australian type approval according to AS/NZS 4770:2000 + transmitter RSE tests to the limits specified in Annex 6, section 6.1.2 of CEPT/ERC/Recommendation 74-01E • Article 3.
PAGE 134
COMPLIANCE EUROPEAN R&TTE DIRECTIVE WARNING: You should not transmit from your transceiver or tune the antenna unless people are beyond the safe working distance for the installation.
PAGE 135
COMPLIANCE EUROPEAN R&TTE DIRECTIVE Spectral regulations may require the TxD option to be installed in the transceiver. In this case, you cannot add channels with new transmit frequencies. You can, however, add receive-only channels, and channels with the same transmit frequency as an existing channel. If the TxP option is installed in the transceiver, you cannot add channels.
PAGE 136
COMPLIANCE EMC AND SAFETY NOTICES EMC and safety notices Radiation safety (non-EU installations) To ensure optimal transceiver performance and to avoid exposure to excessive electromagnetic fields, the antenna system must be installed according to the instructions provided. WARNING: High voltages exist on the antenna during transmission and tuning. Do not touch the antenna during these activities. RF burns may result.
PAGE 137
COMPLIANCE EMC AND SAFETY NOTICES Sécurité des radiations (installations non-EU) Pour assurer la performance optimale de l’émetteur-récepteur et pour éviter une exposition excessive aux champs électromagnétiques, le système d’antenne doit être déployé selon les instructions fournies. ATTENTION: De hautes tensions RF sont présentes au cours de la transmission et de la syntonisation. Ne touchez pas l’antenne pendant ces activités, au risque de vous brûler.
PAGE 138
COMPLIANCE EMC AND SAFETY NOTICES EMC CAUTION: If it is necessary to remove the covers at any stage, they must be refitted correctly before using the equipment. To ensure that compliance with the EMC Directive is maintained. Use standard shielded cables supplied from Codan (where applicable). Ensure the covers for the equipment are fitted correctly. Cover unused connectors on the RFU with the protective caps supplied to prevent electrostatic discharge passing through your transceiver.
PAGE 139
COMPLIANCE EMC AND SAFETY NOTICES WARNING: The protective cover must always be fitted when the 3020 Transceiver Supply is connected to the AC mains. Related links: Earth symbols on page 129 Earth symbols Chassis earth connection points are provided on the Envoy™ Transceiver and 3020 Transceiver Supply. A protective earth is provided in the AC mains wiring of the 3020 Transceiver Supply. This protective earth must be connected at the AC mains supply outlet.
PAGE 140
COMPLIANCE FCC COMPLIANCE FCC compliance FCC Part 90 certification The Envoy™ Transceiver has been tested and certified to FCC Part 90 (FCC identifier code DYY2210). FCC Part 15 compliance Any modifications made to the Envoy™ Transceiver and 3020 Transceiver Supply that are not approved by the party responsible for compliance may void your equipment’s compliance under Part 15 of the FCC rules.
PAGE 141
COMPLIANCE IC CERTIFICATION IC certification Product markings and labelling The Envoy™ Transceiver is certified to IC standards (IC identifier 1029A-1). L’émetteur-récepteur Envoy™ est certifié conforme aux normes IC (Code d’identification IC : 1029A-1).
PAGE 142
COMPLIANCE RCM APPROVAL RCM approval The Envoy™ Transceiver meets the requirements of the Australian Communications and Media Authority: Radiocommunications (MF and HF equipment—Land Mobile Service) Standard 2003 (AS/NZS 4770) and Radiocommunications (HF CB and Handphone Equipment) Standard 2008 (AS/NZ 4355).
PAGE 143
INDEX Index Numerics 2220 Handset 3 2221 Handset 5 entering text 47 2230 Desk Console 7 A advanced view 36 antenna manual tune 9 selecting 29 B basic view 36 brightness setting 70 C call adding from the Call Log/Call History 102 adding to contact Channel Test 23, 96 Emergency 23, 96 Get Position 23, 96 Get Status 27, 99 Message 24, 97 Phone 26, 98 RFDS Emergency 100 Selective 23, 96 Send Position 23, 96 from Emergency key 8 making Message 73 Selective 71 ENVOY™ TRANSCEIVER GETTING STARTED GUIDE to a c
PAGE 144
INDEX adding 22, 94 adding Channel Test call 96 adding Emergency call 23, 96 adding from the Call Log/Call History 102 adding Get Position call 23, 96 adding Get Status call 27, 99 adding Message call 24, 97 adding Phone call 26, 98 adding RFDS Emergency call 100 adding Selective call 23, 96 adding Send Position call 23, 96 cooling 105 crosspatch operating mode 9 changing 90 overview 88 G Get Position call adding to contact 23, 96 Get Status call adding to contact 27, 99 GPS information using 79 H handset
PAGE 145
INDEX P mobile 108 cables 110 connecting control cable to automatic tuning antenna 112 connecting to battery power supply 113 mounting 110 mounting handset and speaker connector 111 mounting handset cradle 110 mounting RF unit 111 mounting speaker 111 peripheral selecting 30 Phone call adding to contact 26, 98 program profile USB stick 91 program secure keys USB stick 91 R read profile USB stick 91 relative humidity 105 RFDS Emergency call adding to contact 100 RFU size 106 weight 106 S scanning 65 pau
PAGE 146
INDEX This page has been left blank intentionally.
PAGE 147
www.codanradio.com ASIA PACIFIC (Head Office) EUROPE, MIDDLE-EAST & AFRICA AMERICAS Codan Limited 81 Graves Street Newton SA 5074 AUSTRALIA Codan (UK) Ltd Unit C4, Endeavour Place Coxbridge Business Park Farnham Surrey GU10 5EH UNITED KINGDOM Codan US, Inc. 1 Fishers Road Pittsford NY 14534 USA T: +61 8 8305 0311 F: +61 8 8305 0411 T: +44 1252 717 272 F: +44 1252 717 337 T: +1 585 419 9970 F: +1 585 419 9971 asiasales@codanradio.com uksales@codanradio.com ussales@codanradio.