MODEL:CD-RA195 CD PLAYER with DUAL ALARM CLOCK RADIO & 2.
TABLE OF CONTENTS Setting the Time and Date ....................18 Setting the Area Code .....................18-19 Adjusting the Contrast .........................19 Setting the PBX Number ......................19 Turning PBX Mode On or Off .................19 Changing the Pause Time .......................... 19 Deleting Message Waiting Indication .....19-20 Turning Auto Answer On or Off .............20 Disabling the Ring for Private Calls ......20 Disabling the Ring forUnavailable Calls ......
IMPORTANT SAFETY INSTRUCTIONS 8. When inserting the batteries into this product, the proper polarity or direction must be observed. Reverse insertion of batteries can cause charging, which may result in leakage or explosion. 9. Remove the batteries from this product if the product will not be used for a long period of time (several months or more) since during this time the batteries could leak, damaging the product. 10.
CD-RA195 PARTS CHECKLIST BATTERY CAUTIONARY INSTRUCTIONS BATTERIES: CAUTION To reduce the risk of fire or injury to persons, read and follow these instructions: For the cordless handset, use only 3.6V 600mAh Nickel Cadmium (Ni-Cd), cordless telephone battery pack (included). Do not dispose of the batteries in a fire. The cells may explode. Check with local codes for possible special disposal instructions. Do not open or mutilate the batteries.
NAME OF PARTS NAME OF PARTS 1.DC jack 2.Headphpne jack Battery Compartment 1.Hands et 2.VOLU ME ControI 3.Ala rm SET ON OF F 4.Time 5.CD/D isplav 6.SLEEP 7.POWER 8.DBBS Switch 9.SNOOZ E Control 1 0.ALAR Ml lndicator 11.ALAR M2 lndicator 12.STOP 1 3.Plav/ Pause 1 4.Minu te/Rew Hour/F.F 1 5.OPEN/CLOSE 16.NlGHT Li ght 17.PROG 18.RANDOM 19.REPEAT 20.CD/FM/A M Switch 21.Music/Buzzer Swit 22.
Opration Before connecting to the power suppI yJ ensure that the rated voItage of this unit matches you r Iocal voItage. Desk or TabIe Top Use 1. Connect the modular jack on the handset with the coiled cord. 2. Connect moduIar jack on the phone and the jack on the wall with the straight cord. Battery lnstallation 1.Open the cover of the battery compartment and install the 9V type batteries. 2.Connect the coiled cord to the handset and the teIephone base. 3.
Time Settlng (1) .Setti ng the hou r:WhiIe d epres sing the Tl ME b utton,pres s ho ur button to a adjust the hour unt il des ired hour is displ ayed. releese both b uttons. (2) .Setti ng the minute:While depressing the TIME butto n,pr ess MINUTE but ton to adjUSt the minut e,untll de sired minu te is displa yed. Release both buttons . Alarm S ettin g(DUal ala rm) (1) .Slide alarm switch to Set position. (2) .Pres s hour and minute buttons until desir ed time is displayed. (3) .
LOCATION OF CONTROLS AND FEATURES(Telephone) LCD Display New call msg. waiting led indicator Na m e C ha ra cte r Fie l d Nu m b e r Fi e ld The LCD is back lit under the following conditions: 1. While receiving an incoming call (during ringing). 2. For 20 seconds , when the handset is picked up from the cradle. 3. For 20 seconds , when any button is pressed in any mode. * The LCD back light goes off immediately after the handset is placed on the base.
HANDSETAND AND BASIC DISPLAYS HANDSET BASIC DISPLAYS BATTERY INSTALLATION To install the 3.6V 600mAh cordless handset battery pack: 1.Slide open the battery compartment door on the back of the handset. 2.Plug the battery connector into the 2-pin connector in the battery compartment, and then insert the battery. 3. Close the battery compartment door. 4. Place the handset on the base unit cradle. 5.
BASIC OPERATION Redialing 1. Press SETTINGS Auto Answer On/Off: Turns on and off the feature which makes the phone automatically go off-hook when the handset is picked up from the base while the phone is ringing. . 2. Wait until you hear a dial tone, and then press to redial the number last dialed (up to 32 digits). Note: You can also press first to display the number and then press to dial the number displayed.
SETTINGS 3. Press to change the setting." --- " will begin flashing. 4. Use the dial pad to enter the three digit area code that your phone number begins with. 5. When the setting you desire is displayed, press to save the setting. A double beep will sound to confirm the setting has been saved. 6. Continue with programming or press to return to the idle screen. Adjusting the Contrast The contrast is optimized for viewing and will probably not need to be changed from the default setting.
SPEED DIALING SPEED DIALING 3. Enter the name you wish to store using the dial pad to enter the letters (up to 15 letters). See the following letter table for how to program the letters using the number pad. To add a space between words, push . Example: For JOHN SMITH dial this sequence: 5 666 44 66 1 J O H N space 7777 S 6 444 8 44 M I T H 4. Press ,and dial the number you wish to store (up to 16 digits). Press to insert a dialing pause into the number. 5.
SPEED DIALING CALLER ID 2. Press to go the entry to be blocked. 3. Press the button twice. The LCD will show the "REJ" icon. Note: When an error is received, none of the data from this call is saved in memory. 4. Press to exit the phone book. Note: priority and Blocked calls will only work if the incoming call's number exactly matches the one that is stored in memory. Display shows when a voice mail message has been received and is stored by message waiting service provided by the phone company.
MESSAGE WAITING AND OTHER FEATURES CALLER ID 2. Place the handset back into the base or press the key on the handset to stop the page/find feature. Out-of-Range Warning: If you venture too far from the base, the handset will beep and the display will show "OUT RANGE". Reverse your direction to re-establish connection with the base or the call will be dropped. When the base detects that the handset has been out of range for 20 continuous seconds it will release the engaged line.
CARE MAINTENANCE AND TROUBLESHOOTING Caller ID service may not work when the phone is connected to a Private Branch Exchange (PBX). The caller has requested that their phone number be suppressed from Caller ID service, or caller ID service is not available in their area. "Private" or "Unavailable" will appear on the display. You answered the call before Caller ID data was displayed, which usually occurs after the first ring. New Call/Message Waiting Indicator doesn't work properly.