SAILOR SP3530 Portable VHF ATEX User manual
Emergency procedure • Turn the knob at the top of the radio clockwise. The display lights up showing the last used channel and the battery level. • Select channel 16 (Distress or Safety), press the 16/C key. • Press the PTT and say: - “MAYDAY, MAYDAY, MAYDAY”, - “This is”..... ships name repeated three times - “MAYDAY” - “This is”.....
IMPORTANT INFORMATION Safe use of ATEX equipment: 0850 • Do not change the battery in wet or humid environments. • Always keep battery connectors dry and clean. • Use only with Sailor ATEX approved accessories. Alternatively ATEX approved accessories in compliance with the accessory connector ATEX specification may be used. • Do not change accessories in wet or humid enviroments. • Do not charge the battery in hazardous area.
SP3530 ATEX VHF Document number: 98-124306-I Release date: June, 2014 Copyright: © 2014 Thrane & Thrane A/S. All rights reserved. Trademark Acknowledgements • SAILOR is a registered trademark of Thrane & Thrane A/S. • Other product and company names mentioned in this manual may be trademarks or trade names of their respective owners. Warranty limitation IMPORTANT - The radio and batteries are sealed waterproof units.
Precautions Avoid water and salt in the I/O connector and keep it clean frequently. Only use original Thrane & Thrane battery packs. Make sure they are clean and dry before attaching the transceiver. Be careful not to damage any gaskets. Only use the original Thrane & Thrane charger for the rechargeable battery. Be very careful when handling the Lithium batteries. With correct use they are safe but any misuse might cause dangerous situations.
Training information SAILOR SP3530 ATEX VHF is designed for "occupational use only". It must be operated by licensed personnel only. The SP3530 complies with the FCC RF exposure limits for "Occupational Use Only". • FCC OET Bulletin 65 Supplement C, evaluating compliance with FCC guidelines for human exposure to radio frequency electromagnetic fields. • American National Standards Institute (C95.
iv
Chapter 1 Introduction Your ATEX VHF .....................................................................1 Performance ....................................................................... 2 Channels ............................................................................. 2 Chapter 2 Operation Controls ............................................................................... 5 Keys and buttons ................................................................5 The display ......................
Chapter 5 Equipment and accessories External equipment ........................................................... 27 List of equipment .............................................................. 27 Connecting external equipment ........................................ 27 Impact on radio operation ................................................28 Accessorie connector ........................................................28 Accessories ...................................................................
Chapter 1 Introduction Your ATEX VHF The SP3530 ATEX VHF is designed for flexibility in daily use. It connects easily to external equipment like headsets and fist mikes, making the SP3530 suitable for any noisy environment. Main features: Unique man machine interface, an excellent grip even with gloves, and large tactile buttons. Display with red adjustable backlight which makes the display visible even at night. Built-in “sleep” function, minimizing power consumption and improving battery lifetime.
Introduction Performance For best performance of the transceiver keep the following in mind: • Keep clear of metal environment. • Hold the transceiver vertically and 10 cm from lips and push the PTT when transmitting. • In receive mode carry the transceiver vertically with belt clips. • To preserve battery power, adjust squelch to close the loudspeaker when there is no signal. • If you are in a lifeboat keep the antenna as high as possible.
Introduction Channel modes The notes in the following sections list the channel restrictions that apply for each channel mode. For information on how to select a channel mode, see Entering and using Configuration mode on page 19 and CHAN on page 20. National frequency regulations shall always be respected and might restrict operation for this type of equipment. International channels Note: Tx power is limited to 1 W on channels 75 and 76.
Introduction Canadian channels Notes: • Tx power is limited to 1 W on channels 15, 17, 20, 65, 66 and 77. • The channels 19, 22, 63, 75, 76 and 81 cannot be selected. • The Weather channels (CA W-ch. in the channel table) can only be used in Rx direction. • The channel 21 can only be used in Rx direction, marked 21B. Tx direction is blocked. • The channels 4, 5, 7, 18, 19, 21, 22, 61, 62, 64, 65, 66, 78, 79, 80, 81 and 82 may only be used as simplex channels (and marked A).
Chapter 2 Operation Controls Keys and buttons 1. 1 On/off/volume 2. Light/Lock 3. Push To Talk (PTT) 4. Up key 5. Down key 2 3 6. Hi/Lo output power 7. Squelch 4 7 5 8 6 9 8. Scan 9. Priority channel (16)/ Call channel 10.
Operation Key presses Pressing and holding certain keys gives access to additional functions, shown in the table below. Key Short press (1 beep) Show next available item in the list (up or down). Default: Channel selection Long press (2 beeps) Run through available items, or select tagged channels A () or B (). Activate Squelch control (Adjust with up/down arrows). Monitor function. Open Squelch completely. Set period of time in configuration mode. 1 press: Activate/ terminate Dual/Triple watch.
Operation The display The display holds various fields of information, explained below. 4 5 6 3 2 7 8 1 9 11 1. 10 Current working channel. 2. Current channel mode. 3. “Lo”: Reduced transmitter power. Full transmitter power is not shown in display. 4. Dual/Triple watch activated. 5. Current working channel is marked for scanning. 6. Keypad is locked. 7. Battery level indicator. 8. Transmitting (Tx) /Receiving (Rx). 9. Accessory is connected. 10. Service line for various purposes.
Operation Using the VHF Basic functions Note Before using the radio, mount the antenna at the top of the radio. The antenna is delivered with the radio. Switching the radio on and off • To switch the radio on, turn the knob at the top of the radio clockwise. The display lights up showing the last used channel and the battery level. • To switch the radio off, Turn the knob back counter-clockwise until it clicks.
Operation Activating a call To activate a call to the selected channel, press and hold the PTT button on the side of the radio. The radio transmits as long as the PTT button is pressed. A small Tx sign next to the channel number indicates when the radio is in transmit mode. Adjusting the volume • To increase the volume, turn the on/off knob at the top of the radio clockwise. • To decrease the volume, turn the knob counter-clockwise. The display shows the level of the volume, e.g.
Operation Using Dual/Triple watch • To activate Dual/Triple watch, press the SCN key. The display shows “Dual” or “Tri” at the top and “16” at the bottom right. The radio toggles between the selected channel and channel 16 in Dual watch. In Triple watch, the radio shifts between channel 16, the call channel and the selected channel. To select whether the SCN key should activate Dual or Triple watch, refer to Configuring the radio on page 19. • To terminate Dual watch, press SCN again.
Operation Other functions Programming the Call channel To program the Call channel, do as follows: 1. Press and hold 16/C until the current Call channel number is flashing. 2. Select the channel with or . 3. Press 16/C to confirm within 3 seconds. Programming the scanning memory To add a channel to the scanning memory, select the channel and then press and hold the SCN key until the display shows MEM at the top.
Operation transmitting is prohibited (reporting "BUSY") if a (silent) carrier containing any sub-tone is active on the channel while pressing PTT. Channels programmed with CTCSS will have a clear identification in the service field, e.g. "CTCSS 22", while selected. Not all channels are allowed for CTCSS use.
Operation Note Prior to any initiation of scrambling, the operator must always identify the calling station in clear voice (unscrambled) on that channel. Use of scrambling may also be restricted by national laws. Narrow band operation The radio is prepared for narrow band operation. If narrow band operation is selected (see BAND on page 25), the number of channels are doubled in the maritime channels, according to international recommendations. Refer to the channel table in Channels on page 2.
Operation “ALIVE” function is also deactivated when • The channel is changed. • The radio is turned OFF and ON again. • Watch or scanning is enabled. • Squelch is open.
Chapter 3 Batteries Battery level indication When the battery level is low, you should recharge the battery. The radio display shows the battery status. When the battery symbol is empty and flashing, the battery should be recharged as soon as possible. Removing and inserting the battery pack To remove the battery pack, do as follows: 1. Open the safety lock as shown. 2. Remove the battery. To insert the battery pack, attach the battery and then close the safety lock.
Batteries The battery charger The chargers has two compartments. CH3505 • A compartment for recharging the battery alone or while attached to the radio. CH3507 • A rear compartment only for storing a spare battery. It does not have a charger function. • A front compartment for recharging the battery alone or while attached to the radio. CH3508 • It is possible to charge a battery in rear compartment simultaneously with the radio/battery in front.
Batteries When mounting the charger, make sure it is placed in a dry place and away from direct sunlight. The charger is not waterproof. Connecting to power The charger can be supplied from DC or from AC using an AC/DC converter. DC: Connect the 12-24VDC Connection Cable between the DC supply and the connector on the underside of the charger. AC: Connect the AC/DC converter to the connector on the underside of the charger. Then connect the AC/DC converter to the AC outlet.
Batteries Charging time with emtpy battery: VHF off approx. 4 hours, VHF on: approx. 5 hours. The battery indicator on the radio display indicates if the radio is placed in the charger while radio and charger are both powered.
Chapter 4 Configuring the radio Configuration mode Entering and using configuration mode Note The radio is not operational in configuration mode. • To enter configuration mode, press and hold the Light/Lock button while turning on the radio. The bottom line of the display shows the current menu item/setting. • To exit configuration mode, turn off the radio or press any key except , and the Light/Lock button.
Configuring the radio List of configuration settings The following settings are available in configuration mode. Name LIGHT Values Description MAN Only Light/Lock button activates the backlight. KEY All keys and buttons, except PTT and volume control, activate the backlight. INT International channels. US US channels. CA Canadian channels BI Inland waterways. ATIS and ATIS killer is enabled. All multiple watch is disabled. ALT Custom defined.
Configuring the radio Name SLEEP Values ON Description Enable sleep mode (to minimize power consumption). Sleeps for periods of 1 second after 15 seconds of idle mode. Idle mode is: no signal detected and no operation of the radio. OFF Disable sleep mode. CONTRST 1, 2, 3, 4, 5 Contrast. 1 = lowest and 5 = highest. SHANG OFF Off. Resumes scanning when signal disappears. 4, 6, 8, 10 Scan hang time (in seconds) on an active receiving working channel.
Configuring the radio Name SQ WORK Values Description TIME A long press on SQ opens squelch. The squelch level resumes to setting 3 seconds after SQ is released. MAN A long press on SQ opens squelch. The squelch level resumes to setting as soon SQ is released. ON If the distress or call channel is selected using the 16/C key, any push on or will select the working channel active when 16/C was pushed.
Configuring the radio Name 123456789 Values 0-9 Description In ATIS programming mode: • Select the digit position with the Light/Lock button. • Select the digit with or . • Press Light/Lock to confirm programming. Note: All digits must be programmed. PREFA OFF Remove tag “A” for current working channel. ON Tag current working channel with “A”. If another channel was previously tagged “A”, this is overruled. • The working channel can now be selected with a long press on .
Configuring the radio Name SUBC Values OFF Description SUBC disabled. Squelch opens on all received signals. 1, 2, ..., 38 Sub-tone carrier ID. Squelch opens if the received signal contains the desired subtone. During transmission the sub-tone with the corresponding ID is generated. Two radios on the same channel and with the same sub-tone ID, can reduce unwanted incoming traffic from other users on the same channel. CTCSS OFF CTCSS disabled. ON Activate CTCSS on working channel.
Configuring the radio Name SCRM Values Description OFF Scrambler disabled. ON Activate scrambling on working channel. Two radios on the same channel and with scrambling enabled, can have a certain level of privacy. Note that if you choose this option, the radio immediately exits configuration mode and starts scrambling on the working channel. BAND 25.0 Wide band operation selected. 12.5 Narrow band operation selected. • Intercepted channels will be denoted 2XX.
Configuring the radio Name ADD NAME Values A-Z, 0-9 Description Makes it possible to name the channels. The name must contain a maximum of 9 characters, use only capital letters, digits and spaces. Note: The name appears in the service line on the display.
Chapter 5 Equipment and accessories External equipment List of equipment The following equipment can be connected to the radio: • SAVOX C400AV Push-To Talk unit • SAVOX C500 Fist Mike • SAVOX NC/400 Noise-com • SAVOX HC-E Helmet-com • SAVOX K53004 Helmet unit • Peltor MT7H79 Headset We recommend to remove all accessories during emergency use. All accessories listed might be used when body worn.
Equipment and accessories When external equipment is connected to the radio, the right side of the display will show a headset. Impact on radio operation The external equipment can have a built-in PTT button, speaker and microphone. Thus a connection has per default the following impact on the radio operation: • If a speaker or earpiece is built into the detected external equipment, the sound device of the external equipment is used, and the internal radio speaker is disabled.
Equipment and accessories Accessories List of accessories The following accessories are delivered with your radio: Accessory Part number ATEX Secondary battery (blue, rechargeable), B3504 403504A ATEX Compact Charger, CH3505 403505A AC/DC converter, length 150cm (100-240V~ /12VDC out) 88-125538 12-24VDC Connection cable, length 150cm 37-124381 Belt clip 62-124320 Antenna 88-124370 Lanyard 41-124375 User Manual (this manual) TT 98-124306 Batteries, charger, AC/DC Converter and 12VDC Connec
Equipment and accessories Accessories you may buy Accessory Part number ATEX Charger, CH3507 403507B ATEX Dual Position Charger CH3508 403508B ATEX Leather Case with shoulder strop 403500-207 Leather Case Warning! The display must always be kept away from the body to reduce the RF explosure when body worn.
Equipment and accessories Attaching and removing the belt clip To attach the belt clip, slide the belt clip upwards into the rails at the back of the radio until it locks. To remove the belt clip, press the projection at the top of the belt clip to release the lock and slide the belt clip downwards out of the rails. Release lock Attaching the lanyard Do as follows: Top view 1. Take the lanyard through the eye at the top of the radio. 2.
Equipment and accessories 32 0845
Chapter 6 Troubleshooting Displaying errors Some errors result in an error message in the display. These error messages are listed below. Display text Problem Type Actions Err The battery voltage is Severe. Change/recharge below a critical level, Radio is non- the battery. where further operation functional. would damage the battery. Err Hardware error. Severe. Service required. Radio is nonfunctional. Context fails operation.
Troubleshooting 34 0845
Appendix A Technical specifications Technical data SP3530 General Item Specification Rx frequency range, landmobile 148.000 - 174.000 MHz Tx frequency range, landmobile 148.000 - 174.000 MHz Rx frequency range, maritime 155.000 - 163.425 MHz Tx frequency range, maritime 155.000 - 161.450 MHz Modulation 25 kHz 16K0G3E 12.5 kHz 8K50G3E Power supply 7.2 VDC Li battery Current drain at 2 W Tx 1A Current drain at 0.4 W Tx 0.7 A Current drain Rx max audio 0.
Technical specifications Item Specification Water ingress protection IP67 Frequency stability Better than ±0.7 kHz Weight with emergency battery 370g Transmitter Item Specification RF output power 2 W /1 W RF output power, Canada 1.7 W ±0.7 dB / 0.8 W ±1 dB Max deviation 25 kHz ±5 kHz 12.5 kHz ±2.5 kHz Spurious emission < 0.25 uW Adjacent channel power 25 kHz > 70 dB 12.
Technical specifications Item Specification Intermodulation 25 kHz > 68 dB 12.5 kHz > 65 dB Spurious response > 70 dB Adjacent channel selectivity 25 kHz > 70 dB 12.5 kHz > 60 dB Audio output, internal 0.25 W at 10% dist. Audio output, external 0.
Technical specifications Battery life guidelines Note New batteries should be placed in the charger CH3505, CH3507 or CH3508 for minimum 12 hours first time. During daily use, always keep the battery fully charged and away from hot areas. Keep the battery terminals dry and clean. Never discharge beyond the specifications of the battery. Operation/Standby time depends on usage. Generally, the more the radio is transmitting, the faster it will drain the battery.
Technical specifications 280 Dimensional drawing, transceiver 66 0845 55 39
Technical specifications Dimensional drawing, chargers 87 CH3505 70.4 80 Mounting Possibillities Desktop mounting, top view Wall mounting, rear view 46.8 30.
Technical specifications CH3507 and CH3508 Mounting Possibillities Desktop mounting, top view 0845 Wall mounting, rear view 41
Technical specifications Declaration of Conformities Thrane & Thrane A/S Declaration of Conformity with ATEX Directive 94/9/EC &# 3,"#01'%,#" -$ 2&'1 *#22#0 "#!* 0#1 2& 2 2&# $-**-5',% #/3'.+#,2 !-+.*'#1 5'2& 2&# 1.#!'i! 2'-,1 -$ "'0#!2'4# toGtG !-,!#0,',% #0+', * /3'.+#,2@ Equipment npnk -02 *# + 0'2'+# 0 "'-Q telephone (non GMDSS) or -02 *# 0 "'-2#*#.
Technical specifications Thrane & Thrane A/S Declaration of Conformity with R&TTE Directive 1995/5/EC &# 3,"#01'%,#" -$ 2&'1 *#22#0 "#!* 0#1 2& 2 2&# $-**-5',% #/3'.+#,2 !-+.*'#1 5'2& 2&# 1.#!'i! 2'-,1 -$ "'0#!2'4# ltttGpG !-,!#0,',% "'- 9 #*#!-++3,'! 2'-,1 #0+', * /3'.+#,2@ Equipment included in this declaration npnk npkn npko npkp npkr npks nptp -02 *# + 0'2'+# 0 "'-2#*#.
Technical specifications 44 0929
Technical specifications 0929 45
Technical specifications 46 0929
Appendix B Attention Gore-Tex Membrane To keep the ATEX VHF watertight, is it very important that the Gore-Tex membrane behind the label under no circumstances must be damaged/ covered or removed. That is, do not remove/cover the label and the Gore-Tex membrane or place any other labels in the area.
Attention 48 0845
98-124306-I www.cobham.
