Bluetooth Hands-Free Car Kit HCC-100A User Manual
[Table of Contents] Before use Package contents Description of parts Recommended installation position Charging Low battery Battery status Solar power charging status How to use Power on/off Pairing Connecting Answering a call Making a call Ending a call Volume control Functions during a call Summary of button functions LED indication and signal sound Supplement Troubleshooting Cautions Additional information Standards and specifications Limited warranty 2 3 4 4 6 6 6 7 8 10 12 12 13 13 14 15 16 17 18
Before use The Clipcomm HCC-100A is a solar-powered Bluetooth handsfree car kit with a slim and fashionable design. It provides crystal clear sound and excellent ease of use because of its simple and user-friendly interface. [Package contents] Ensure that the items mentioned below are all included in the package. If any item is missing, please contact the dealer.
Before use [Description of parts] Microphone Status LED Multifunction button Volume controls / Speaker Battery status LED Charging port 3M tape Suction cup hole Solar panel Suction cup hole 3M tape 3
Before use [Recommended installation position] It is recommended that the hands-free car kit be positioned and installed on the top-left of the windshield, as shown in the picture below. (The hands-free car kit can be installed using either 3M tapes or suction cups.) Installing the hands-free car kit in the recommended position will lead to more efficient solar power charging and better performance with regard to the microphone. Ensure that the hands-free car kit does not obstruct the driver’s view.
Before use Charge your hands-free car kit until the battery status LED turns off. The unit will be fully charged in approximately 2 h. 2. Using solar power Direct the solar panel on the back of the hands-free car kit toward the sun. (Please refer to the recommended installation position, as mentioned above.) If the car kit receives sufficient sunlight for 3 h, you can talk for a duration of up to 30 min.
Before use [Low battery] The status LED will flash blue and the battery status LED will flash red simultaneously with a periodic beeping sound when the battery status is lower than 10% out of full charge. In this low battery status, the battery status LED and the status LED will operate simultaneously in the same way. Charge the battery as soon as the abovementioned phenomenon is detected. The product will turn off when the battery is not charged.
How to use [Solar power charging status] To check the solar power charging status, you can press for 5 s when the hands-free car kit turned on. If the car kit is receiving sufficient sunlight, the battery status LED will glow red. (Once the battery is fully charged, the battery status LED will turn off.) Press for 5 s again to turn off the battery status LED. It is recommended to turn off the battery status LED during the solar power charging.
Before use [Pairing] Before using your hands-free car kit with mobile phone for the first time, you must pair it with your Bluetooth mobile phone. (For the detailed set up and pairing instructions with mobile phone, please consult your mobile phone user guide.) There are two pairing mode methods with HCC-100A. Easy Pairing 1. With the power off, press and hold to turn on the product. button for 2 seconds, 2. The hands-free car kit will enter Auto-Reconnect mode, for 7 seconds.
How to use used. (Pairing with the hands-free profile is recommended since the user can utilize the various Bluetooth functions in this profile.) 6. Select “Solar Car Kit” from the list of searched devices. 7. When prompted for a passkey, enter 0000. 8. A beep will sound when the devices are paired successfully. Easy Pairing 1. Begin with the hands-free car kit turned off; then, press and hold down for 5 s. 2. You will hear two short beeps after the booting tone, and the status LED will glow blue steadily.
How to use 6. A beep will sound when the devices are paired successfully. 7. After you have successfully paired your phone and the hands-free car kit, you do not need to repeat these steps each time you use the hands-free car kit with your mobile phone. The hands-free car kit will turn off automatically if it stays in the “pairing mode” for over 3 min without being paired to any device. In this case, you have to reattempt the pairing process (see abovementioned steps).
How to use without the paring process when the hands-free car kit turns on. (The mobile phone connected previously should be within 10 m from the car kit.) 2. Out of range The hands-free car kit will be automatically reconnected when it is brought back within a 10-m range of the phone within 3 min. Please press once briefly to connect it immediately. When out of range (greater than 10 m), the connection between the hands-free car kit and the mobile phone will be dropped.
How to use [Answering a call] The hands-free car kit and mobile phone will ring simultaneously when an incoming call is received. You can answer a call by pressing briefly. (The call can also be answered using the mobile phone.) Ringing mute In order to activate the mute function when an incoming call is received, press and hold for 1 s; this will mute the ringing sound. (This function may be used to maintain silence inside the car.) To release the mute function, press and hold for 1 s again.
How to use This function is only available if your mobile phone supports the voice dialing function and the hands-free car kit is paired as a hands-free device. If your mobile phone does not support voice dialing, the hands-free car kit will activate the last number redial feature. The hands-free car kit may not activate any action; this depends on the features of different models of mobile phones. Last number redialing * Press and hold for 1 s; this will activate the last number redial feature.