User's Manual

ManualsBrandsClimax Technology ManualsElectronicsClamp Meter

Clamp Meter (CLMT-1ZBS)

CL-Meter-ZBS is a ZigBee Clamp Meter aim to monitor and report the total amount of electricity uses in your

facility by connecting the clamp onto the power cable.

The Clamp Meter utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless

communication protocol that is reliable and has low power consumption and high transmission efficiency. Based

on the IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network and

coordinated for data exchange and signal transmission.

The Clamp Meter serves as an end device in the ZigBee network. It can be included in the ZigBee network to

transmit signal upon activation, but cannot permit any other ZigBee device to join the network through the Clamp

Meter.



Parts Identification

1. Red LED

Flash twice quickly:

The Clamp Meter has successfully joined a ZigBee network.

Flashes once:

When Clamp Meter is reset.

Flash once every 20 minutes:

The Clamp Meter has lost its connection to its current ZigBee network.

2. AC Input cable

3. Current Transformer Cable (CT1)

4. Current Transformer Cable (CT2)

5. Function Button

-Press the button once to report the value of the meter to the ZigBee network.

-Press and hold the button for 10 seconds then release to reset the Clamp Meter.

6. Reserved

7. Mounting Hole

8. Mounting Hooks

9. Mounting Bracket

Summary of content (6 pages)

PAGE 1
Clamp Meter (CLMT-1ZBS) CL-Meter-ZBS is a ZigBee Clamp Meter aim to monitor and report the total amount of electricity uses in your facility by connecting the clamp onto the power cable. The Clamp Meter utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless communication protocol that is reliable and has low power consumption and high transmission efficiency. Based on the IEEE802.15.
PAGE 2
Installation  Wiring WARNING Wiring of the device should only be performed by a licensed electrician. The circuit box’s main breaker should be turned off to perform installation. The insertion hole wire specification is AWG18 or Ø 1.02 (mm²). The Clamp specification is 60A Ø10mm Please make sure the main power in your facility is also off before installing. Follow the steps below: 1. Connect AC Input cable to a socket near the Electrical Box to power on the Clamp Meter. 2.
PAGE 3
 Mounting The Clamp Meter has a mounting bracket for mounting purposes. 1. Use the mounting bracket as template to mark the two holes on the wall for installing screws. 2. Screw the mounting bracket onto the wall according to marked location. Install wall plugs if necessary. 3. Locate the hooks of the mounting bracket and line up the hooks with the mounting holes on the Clamp Meter. Fit the hooks into the mounting holes as picture below. Installation is now complete.
PAGE 4
 Energy Consumption Monitor  The Clamp Meter will transmit a signal from the clamp itself with its power consumption data every 10 minutes to the ZigBee network coordinator.  Reading from clamp on Current Transformer Cable CT-1 is reported to ZigBee Endpoint 0x01.  Reading from clamp on Current Transformer Cable CT-2 is reported to ZigBee Endpoint 0x02.
PAGE 5
Enumeration 0x0010 LocationDescription 0x0011 PhysicalEnvironment 0x0012 DeviceEnabled  only Character String 8-bit Enumeration 0 – 32 bytes 0x00 –0xff Boolean 0x00 –0x01 Read / Write Read / Write Read / Write O 0x00 O 0x01 M Attribute of Identify Cluster Information Identifier Name Type Range Access Default Mandatory / Optional 0x0000 IdentifyTime Unsigned 16-bit integer 0x00 –0xffff Read / Write 0x0000 M  Attribute of the Metering Cluster Information Identifier Name Ty
PAGE 6
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.