Installation Instructions

ManualsBrandsClimax Technology ManualsElectronicsWireless Bell Box

Wireless Outdoor Bell Box (BX-23)

The Outdoor Bell Box is used to attract attention when alarm signal is received from Control Panel, by activating its siren and strobe light.The Bell

Box can also alert you to tamper violation, and low battery status. With its two-way radio communication, the Outdoor Bell Box guarantees

successful transmissions sent to the Control Panel. If the Control Panel receives the signal from the Bell Box, it will transmit an acknowledgment

back to the Bell Box.

Identifying the Parts

1. Mounting Holes

2. Power Switch

The switch includes 3 positions:

BT4: The Bellbox is powered by the 4 Alkaline batteries configuration.

Off: The Bellbox is not powered by any battery.

BT2: This configuration is currently reserved.

3. LED Group 3

4. LED Group 2

5. LED Group 1

6. Learn Button

7. Battery Compartment

8. Tamper Switch

Accessories included

In addition to the BX-23 itself, the following accessories are also included in the package:

a. 4 x large wall plugs.

b. 4 x 4 mm x 30 mm cross head fixing screws.

c. 4 x 1.5V D alkaline cells (pre-inserted)

Power Supply

The Bellbox is powered by 4 alkaline D-cells. Switch the power switch to the BT4 position to use battery power.

If low battery condition is detected, the Bellbox will send a low battery signal to the Control Panel.

<NOTE>

 The Power switch position BT2 is currently reserved.

Supervision

The Bellbox will transmit a supervisory signal every 15-18 minutes in normal operation mode. If this signal is not received, the Control Panel will

indicate that the particular BX-23 is experiencing an out-of-order problem.

Function Overview



Alarm Memory

If an alarm was triggered in your absence and the system was not disarmed before alarm length expiry, the Bellbox will sound a short alarm

when the system is disarmed to warn the user that an alarm has been triggered when he is away. This suggests that the intruder could still be

within the premises.



Alarm Length

The Bellbox alarm length is 15 minutes.

When an alarm is activated by Control Panel, the Control Panel will notify the Bellbox to start alarming according to the panel’s own alarm

length setting. When the Panel’s alarm length expires, it will notify the Bellbox to stop alarm.

If the Panel alarm length is set longer than Bellbox alarm length (15 minutes), after an alarm is activated, instead of waiting panel alarm length

to expire, the Bellbox will stop alarming upon expiry of its own alarm length.

If the panel is under disarm mode and the Bellbox tamper switch is triggered, the Bellbox will activate alarm according to its own alarm length

setting (15 minutes) since the panel is under disarm mode and will not activate alarm from tamper trigger.



Siren Tamper

The Bellbox is protected against any attempt to open the lid or to detach the bellbox from its mounting surface.

If the Bellbox detects a tamper condition, it will activate the siren & strobe light for the programmed alarm period. A tamper signal will be sent

to the Control Panel along with regular signal transmissions for the Control Panel to display the status accordingly. If the tamper condition

persists, the Bellbox will sound a series of five beeps either every time the system is armed or when the tamper is enabled, to indicate a fault.

Tamper feature can be disabled temporaily from the Control Panel using Siren Tamper control function. The Bellbox will stop tamper detection

temporarity for one hour. This function is mainly designed for replacing battery or changing Bellbox installation location. After one hour, the

Summary of content (5 pages)

PAGE 1
Wireless Outdoor Bell Box (BX-23) The Outdoor Bell Box is used to attract attention when alarm signal is received from Control Panel, by activating its siren and strobe light.The Bell Box can also alert you to tamper violation, and low battery status. With its two-way radio communication, the Outdoor Bell Box guarantees successful transmissions sent to the Control Panel. If the Control Panel receives the signal from the Bell Box, it will transmit an acknowledgment back to the Bell Box.
PAGE 2
Control Panel will automatically turn the function back ON after the duration. The tamper detection can also be enabled again manually using the Siren Tamper function.  Audio & Visual Status Indication While arming / disarming the system, the BX-23 uses different methods to distinguish various statuses for the user, as listed in the table.
PAGE 3
Step 2. Find the location where the Bellbox is to be mounted. Step 3. Remove the Top cover by releasing the bottom screw using a Philips screwdriver and pulling the outer case out carefully. Step 4. Remove the LED cover by releasing the 2 screws securing the cover using a Philips screwdriver and removing the cover. Step 5. Hold the Bellbox at the position where it will be mounted, supply power to Bellbox. Step 6.
PAGE 4
Step 4: Remove the LED cover by releasing the 4 screws securing the cover using a Philips screwdriver and removing the cover. Step 5: Slide the Power switch to the OFF terminal and (where applicable) disconnect the power adapter. Step 6: Insert batteries into battery compartment. Step 7: Press and hold the Learn Button for 7 seconds and slide the Power switch to BT4 terminal. The Bellbox will emit two beeps followed by one long beep. Step 8: Release the Learn Button when you hear the long beep.
PAGE 5
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.