Parts List

ManualsBrandsClimax Technology ManualsCamera & PhotoPIR Motion Sensor Camera

PIR Motion Sensor Camera

VST-892

Introduction

VST-892 is a passive infrared (PIR) motion sensor camera. It is capable of sending wireless signals and captured images

(picture quality of up to 640 x 480 pixels) to the Control Panel upon movement detection.

The PIR Camera is designed to give a typical detection range of 10 meters when mounted at 2.3-2.5 meters above

ground. For pet-immune models, they will not detect the pets up to 50cm/20kg when mounted at 2.3-2.5 meters above

ground. For models that are compatible with repeaters/routers (P5 models only), the RF communication range can be

further extended into hard-to-reach areas.

VST-892 is designed with the digital proximity detector. The anti-masking feature allows for detection of any attempts to

blind the detector by placing objects in its field of view.

The PIR Camera consists of a two-part design made up of a cover and a base. The cover contains all the electronics and

optics and the base provides a means of fixing. The base has knockouts to allow mounting on either a flat surface or in a

corner situation with a triangular bracket for corner mounting.

The VST-892 Series includes the following models:

VST-892 – PIR motion sensor camera with flash LED

VST-892-IL – PIR motion sensor camera with Infrared LED

Parts Identification

1. Flash LED/Infrared LED

The Flash LED (For VST-892) or Infrared LED (For VST-892-IL)

delivers sufficient light for image capture under low lighting condition.

2. Blue LED/Function Button

Blue LED:

(Please refer to LED Indicator description below for details)

Function Button Usage:

- Press and hold the button for 3 seconds to send a learn code, release

when Blue LED light on.

- Press the button once to enter test mode for 3 minutes.

- Press the button once to send a learn code to the repeater/router. (P5

models only)

3. Digital Proximity Detector

The digital proximity detector is used to detect any masking (blocking) attempt

by an intruder.

4. IR Sensor

5. PIR Camera Lens

6. Battery Compartment

7. Tamper Switch

8. Pet Immunity Enable/Disable Jumper Switch (JP3)

When set as ON, Pet Immunity is disabled.

When set as OFF, Pet Immunity is enabled. (Factory default)

9. Sensitivity Increaser Jumper Switch (JP4)

When set as ON, the PIR’s detection sensitivity is high.

When set as OFF, the PIR’s detection sensitivity is in normal level.

(Factory default)

Jumper On

The jumper link is inserted

connecting the two pins

Jumper Of

If the jumper link is removed or

“parked” on one pin.

Summary of content (6 pages)

PAGE 1
PIR Motion Sensor Camera VST-892 Introduction VST-892 is a passive infrared (PIR) motion sensor camera. It is capable of sending wireless signals and captured images (picture quality of up to 640 x 480 pixels) to the Control Panel upon movement detection. The PIR Camera is designed to give a typical detection range of 10 meters when mounted at 2.3-2.5 meters above ground. For pet-immune models, they will not detect the pets up to 50cm/20kg when mounted at 2.3-2.5 meters above ground.
PAGE 2
Features  LED Indicator In Normal operation mode, the Blue LED will not light except in the following situations:  When the PIR Camera is in low battery condition, every time it transmits a detected movement, the Blue LED will flash for 2 seconds.  When the cover is opened and the tamper switch is violated, the Blue LED will flash for 2 seconds, to indicate it is transmitting “Tamper” signal.
PAGE 3
 Press and hold the function button for 3 seconds, release the button when the Blue LED light on, the Blue LED will light on for 25 seconds in learning mode, add PIR Camera into the Control Panel during this period (refer to your Control Panel to finish learn in process). If the PIR is successfully added into the Control Panel, the Blue LED will flash 6 times to indicate. If PIR is not added within 25 seconds, please repeat learning process.
PAGE 4
VST-892 Detection Range It is recommended to install the PIR Camera in the following locations  Mount where the animals cannot come to the detection area by climbing on furniture or other objects.  Don’t aim the detector at stairways the animals can climb on.  In a position such that an intruder would normally move across the PIR’s field of view.  Between 2.3 and 2.5m above ground for best performance.  In a corner to give the widest view.  Where its field of view will not be obstructed e.g.
PAGE 5
 Corner mounting: 1. 2. 3. 4. 5. 6.  Open the cover by loosening the Cover Screw using a Philips screwdriver. Break through the 4 Corner knockouts at the center of base. Use the holes as template to drill holes on the surface. Insert the wall plugs if fixing it into plaster or brick. Screw the base into the wall plugs. Fit the cover onto the base and tighten. Corner mounting with the triangular bracket: 1. 4 knockouts are made on the triangular bracket.
PAGE 6
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.