Parts List

ManualsBrandsClimax Technology ManualsCamera & PhotoOutdoor Curtain PIR Motion Sensor Camera

Table Of Contents

Federal Communication Commission Interference Statement

Outdoor Curtain PIR Motion Sensor Camera VST-892EXC

VST-892EXC is an outdoor curtain passive infrared (PIR) motion sensor camera. It is capable of sending wireless signals and

captured images (picture quality of up to 640 x 480 pixels) to the Control Panel upon movement detection.

Featuring night illumination capability, with UV resistant housing, and waterproof to IP65 standard, VST-892EXC is ideal for

backyards, lawns, gates, outdoor corridors and hallways.

The Outdoor Curtain PIR Camera is designed to give a typical detection range of 12 meters when mounted at 1.4-2.5 meters

above ground. It two detection options: horizontal curtain and vertical curtain. Horizontal curtain can prevent animals up to 60 kg;

vertical curtain is ideal for perimeter applications.

Besides, VST-892EXC is designed with the digital proximity detector. The anti-masking feature allows for detection of any

attempts to blind the detector by placing objects in its field of view.

VST-892EXC is also compatible with Climax’s Repeater RP-29/Router RMB-29, which can further extend the RF communication

range into hard-to-reach areas.

The VST-892EXC Series includes the following models:

VST-892EXC – Outdoor curtain PIR camera with flash LED

VST-892EXC-IL – Outdoor curtain PIR camera with Infrared LED

 Identifying the Parts

Front View Inside View

1. Digital Proximity Detector

The digital proximity detector is used to detect any masking (blocking) attempt by an intruder.

2. LED Indicator (Red)

The LED indicator is used to indicate the system status.

3. Flash LED / Infrared LED

The Flash LED (For VST-892EXC) or Infrared LED (For VST-892EXC-IL) delivers sufficient light for image capture

under low lighting condition.

4. IR Sensor

The sensor is intended to detect moving objects.

5. PIR Camera Lens

6. Test&Learn Button

-Press and hold the button for 3 seconds to send a learn code, and then release the button when Red LED lights up.

-Press the button once to enter test mode for 10 minutes.

-Press the button once to send a learn code to the repeater/router.

7. Internal Tamper

8. DIP Switch Block

9. Battery Compartment

10. Mounting Bracket

11. Rotating Holder

Summary of content (10 pages)

PAGE 1
Outdoor Curtain PIR Motion Sensor Camera VST-892EXC VST-892EXC is an outdoor curtain passive infrared (PIR) motion sensor camera. It is capable of sending wireless signals and captured images (picture quality of up to 640 x 480 pixels) to the Control Panel upon movement detection. Featuring night illumination capability, with UV resistant housing, and waterproof to IP65 standard, VST-892EXC is ideal for backyards, lawns, gates, outdoor corridors and hallways.
PAGE 2
 LED Indicator When enabled, the LED Indicator will light up in the following conditions:  When the Tamper Switch is triggered, the LED will flash for 6 times to indicate it is transmitting “Tamper” signal.  When the PIR Camera is in fault conditions (tamper open or low battery condition persists), each time it transmits a detected movement, the LED will flash for 6 times.
PAGE 3
 Proximity Detection  The PIR Camera has a digital proximity detector that can detect any masking (blocking) attempt by an intruder.  When a masking event is detected, and the masking condition lasts for 2 minutes, VST-892EXC will send tamper open signal to the Control Panel to notify user of the condition.  After masking/blocking is removed for 2 minutes, VST-892EXC will send tamper restore signal to the Control Panel.
PAGE 4
 Mounting & Installation Method  Mounting with mounting bracket and rotating holder: Step 1. Mount the VST-892EXC with the hooks of the mounting bracket latched on the back cover of the VST-892EXC, and then push downwards until you hear a click sound. Step 2. On the back of the mounting bracket, install a screw to make sure the device is well-secured. Step 3. Fix the rotating holder to the wall with 2 provided screws. Fix the mounting bracket on the rotating holder with fixing screws.
PAGE 5
Step 4. When the top screw of the rotating holder is loose, the VST-892EXC can be rotated horizontally. A calibration line is marked for 0 degree. When the screw on the side of the rotating holder is loose, the VST-892EXC can be rotated vertically. 7 scales are marked for adjusting angles. 1 scale is for 5 degrees and the VST-892EXC can be moved to the maximum of 30 degrees vertically. Step 5. After adjusting the proper angles for the IR Detection, secure the screws on the top and the side.
PAGE 6
Figure 4 Vertical Figure 3 Horizontal Step 4. Secure 4 screws and put the 2 rubber caps on the 2 bottom screws. Step 5. Put the back cover back and secure 2 back cover fixing screws.  After changing IR lens, ensure to adjust Dip Switch 3 settings for appropriate application.  PIR Camera Detection Coverage  VST-892EXC has two detection options: horizontal curtain and vertical curtain, each has different application.
PAGE 7
Horizontal Curtain Mounting Height/Tilt Angle Detection Range Blind Area Pet Immune 1.4 M/0° 12 M 0M 12 M 1.8 M/5° 12 M 0.5 M 9M 2 M/10° 12 M 0.75 M 6M 2.3 M/15° 2.5 M/20° 12 M 12 M 1.5 M 1.
PAGE 8
Limitations:      Do not install the PIR Camera completely exposed to direct sunlight. Avoid large obstacles in the detection area. Do not point directly at sources of heat, such as fires and boilers, or install above radiators. Never attempt to disassemble or modify the unit. Do not install the motion sensor camera where objects moved by wind such as trees and laundry, which may block the motion sensor camera’s field of view.
PAGE 9
 Clear all light reflecting surfaces from the detection area, as well as water puddles.  Avoid looking directly at the path of outdoor unit’s intake or exhaust airflow.  Adjust the Dip Switche 3 setting according to the IR lens direction for appropriate application. If Dip Switch 3 setting does not match with the IR lens direction, the PIR Camera’s performance will be hindered and may cause either false alarm or inability to detect movement.
PAGE 10
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.