Use and Care Manual

ManualsBrandsClihome ManualsOutdoor Heating47000 BTU Black Freestanding Propane Patio Heater with Powder Coated

Owner’s Manual

STEEL PATIO HEATER

DANGER

WARNING

If you smell gas:

1. Shut off gas to the appliance.

3. If odor continues, keep away from

the appliance and immediately call

Do not store or use gasoline or other

vicinity of this or any other appliance.

An LP-cylinder not connected for use

shall not be stored in the vicinity of

this or any other appliance.

Improper installation, adjustment, alteration, service or maintenance can cause injury or

property damage. Read the owner’s manual thoroughly before installing or servicing this

result causing property damage, personal injury or loss of life.

For outdoor use only.

Save these instructions for future use. If

you are assembling this unit for someone

else, give this manual to him or her and

read and save for the future.

3177588

Intertek

WARNING: This product can expose you to chemicalsincluding Lead and Lead Compounds,

which are known to the state of Californiato cause cancer, and Carbon Monoxide, Lead and

Lead Compounds which are knownto the state of California to cause birth defects or other

reproductive harm.For more information go to www.P65Warnings.ca.gov.

Model Number: PH02-S, PH02-SS

Summary of content (13 pages)

PAGE 1
STEEL PATIO HEATER Model Number: PH02-S, PH02-SS DANGER If you smell gas: 1. Shut off gas to the appliance. 3. If odor continues, keep away from the appliance and immediately call WARNING Do not store or use gasoline or other vicinity of this or any other appliance. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. WARNING For outdoor use only.
PAGE 2
SAFETY INFORMATION Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so WARNING • The installation of this unit must adhere to local codes or either the National Fuel Gas Code, ANSI Z223. 1/NFPA54, OR CAN/CGA-B149.1, National Gas and Propane Installation Code. • THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed area.
PAGE 3
damaged parts should this occur. • Do not disconnect any part while unit is in use. • Do not store a spare propane tank on or near this unit. • If the heating unit is indoors, detach the propane tank and leave outdoors. • • Always remove protective cover before operating (if applicable). • Check for leaks after not using the unit for long periods of time. • Children should never operate this unit. Children must be supervised while near this unit. • Keep gas tank at least 5 feet away from unit when lit.
PAGE 4
SAFETY INFORMATION BE CAREFUL: WHEN CERTAIN MATERIALS OR ITEMS ARE STORED ABOVE, BESIDE OR UNDER THIS HEATER WHILE IN USE, THEY WILL BE SUBJECT TO RADIANT HEAT AND COULD BE SERIOUSLY DAMAGED. Combustible materials should not be within 24 inches of the top of the unit, or within 36 inches around the entire unit.
PAGE 5
HARDWARE AA BB CC DD EE FF HH II JJ KK LL MM Item AA BB CC DD EE FF GG HH II JJ KK LL MM Description M6x10 Screw M6 Nut M8 Bolt M6x22Bolt Wrench Reﬂector Stud Wing Nut Washer Anchoring Arm Anchoring Nut Cap Nut Small screw Webbing GG Qty 8 14 3 6 1 3 3 6 3 3 9 9 1 Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any parts are missing or damaged, do not attempt to assemble the product.
PAGE 6
CONTENTS A B C D E F G H J I Item A B C D E F G H I J Page 6 Description Reﬂector Panel Center Reﬂector Head Assembly Post Tank Housing Post Support Support Legs Regulator Base Wheel Assembly Qty 3 1 1 1 1 1 1 1 1 1
PAGE 7
ASSEMBLY INSTRUCTIONS 1. Align the holes in the wheel assembly (J) with the holes in the base (I), attach the wheel assembly to the base using 2 pcs M6x10 screws (AA) and 2 pcs M6 nuts (BB). I J 2. Mount the 3 pcs anchoring arms (II) to the holes on the base (I) using 6 pcs M6x10 screws (AA) and 6 pcs M6 nuts (BB). I I II Optional: If you wish, the patio heater can be fixed by hammering the 3 pcs anchoring nuts (JJ) into ground through the anchoring arms after assembly. JJ 3.
PAGE 8
ASSEMBLY INSTRUCTIONS 4. Attach the post support (F) to the top of the support legs (G) using 6 pcs M6 x 22 bolts (DD) and 6 pcs M6 nuts (BB). F G 5. Place the tank housing (E) on top of the assembly. E 6. (FF) into the top holes of the head assembly (C).
PAGE 9
WARNING sembling! B KK A AA 7. semble the outer rim using one small screw (LL) and one cap nut (KK). Repeat this step with the three M6 screws (AA) and three cap nuts (KK). Tighten all screws tightly. 8. GG HH ers (HH) and three wing nuts (GG). FF C 9. Unscrew the four screws that are preassembled on the head assembly (C). Place the head assembly (C) into the top of the post (D) by inserting the regulator (H) into the post (D).
PAGE 10
ASSEMBLY INSTRUCTIONS 10. Remove the pre-assembled screws from the post support (F) and attach post (D) to the post support (F) using those 4 screws. C D F 11. Place the 20 lb gas cylinder in the center of the base, fasten it with the webbing (MM). MM 12. Turn the cylinder valve on the tank clockwise to close the propane tank. Attach the regulator (H) to the cylinder valve by turning the regulator coupling nut clockwise. Make sure it is fastened securely and tighten connections by hand only.
PAGE 11
OPERATION Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off” position. Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles occur on any connection there may be a leak. If you smell gas or a leak is discovered turn the gas valve off, disconnect propane gas tank and do not use the appliance until the leak is repaired.
PAGE 12
MAINTENANCE • Before performing any maintenance always disconnect propane gas tank. • Keep the heating item free and clear from combustible materials. • Visually inspect burner for obstructions and keep tank enclosure free and clear from debris. • Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner is completely cooled down. Wipe down with a soft cloth. • Harsh weather conditions may cause stubborn stains, discoloration and possibly rust pitting.
PAGE 13
TROUBLESHOOTING Problem Cause Solution The burner will not light. The burner injector is clogged. Clean the burner injector. There is low gas supply pressure. Call your gas supplier. The burner flame goes off immediately after ignition. There is low gas pressure. Call your gas supplier. The ignition is delayed. The main burner carryover ports are clogged. Clean the main burner ports. There is low gas pressure. Call your gas supplier. The combustion on the burner is There is not enough air.