Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. VI • Only use a power adapter approved for use with this computer.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .................................................................................I FCC Statement .............................................................II Instructions for Care and Operation .......................... IV Power Safety .............................................................. VI Battery Precautions ...................................................VII Cleaning .................................................................. VIII Servicing ...............
Preface Power Management Overview ........................................................................3-1 The Power Sources ........................................................3-2 AC/DC Adapter ...........................................................3-2 Battery .........................................................................3-2 Turning on the Computer ...............................................3-3 Power Plans ...................................................................
Preface Non-Fatal Errors .........................................................5-3 The Setup Program ........................................................5-4 Entering Setup .............................................................5-4 Setup Screens ...............................................................5-5 Main Menu .....................................................................5-6 System Time & Date (Main Menu) ...............................5-6 IDE Primary/Master (Main Menu) .......
Preface Trusted Platform Module .............................................7-25 Initializing TPM .......................................................7-25 TPM Module Driver Installation ..............................7-27 Initializing TPM ........................................................7-28 TPM Manager ............................................................7-30 3.5G Module ................................................................7-37 3G Watcher Application ............................
Preface & Weight ...................................................................... C-5 Optional ........................................................................ C-5 Windows XP Information DVD Regional Codes ................................................... D-2 Windows XP Start Menu & Control Panel ................... D-3 TouchPad and Buttons/Mouse ...................................... D-4 Function Keys ............................................................... D-5 Audio Features ......
Preface XVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a of interest to you.
Quick Start Guide Not Included Operating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1.
1 Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the following operating systems are supported.
Quick Start Guide System Startup 1. 2. 3. 4. 5. 6. 7. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle, and press the power button to turn the computer “on”.
1 Quick Start Guide Figure 1 - 2 LCD Panel Open System Map: LCD Panel Open 1 Built-In PC Camera (Optional) 2. LCD 3. Speakers 4. Power Button 5. Hot Key Buttons 6. LED Status Indicators 7. Keyboard 8. Touchpad & Buttons 9. LED Power & Communication Indicators 10. Fingerprint Module (Optional) 11. Built-In Microphone 1. Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Quick Start Guide LED Indicators The two sets of LED indicators (LED Status Indicators and LED Power & Communication Indicators) on the computer display helpful information about the current status of the computer.
1 Quick Start Guide Hot Key Buttons & Keyboard These buttons give instant access to the default Internet browser and e-mail program, and allow you to toggle the Silent Mode on/off with one quick button press. Table 1 - 4 - Hot Key Buttons Hot Key The keyboard has a numerical keypad for easy numeric data input, and features Function Keys to allow you to change operational features instantly. Activate the Number Lock feature by pressing the Num Lk key at the top right of the keyboard.
Quick Start Guide Keyboard The keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 5, on page 1 - 10 for full function key combination details. Function Keys Function Keys Play/Pause Key Numeric Keypad Numerical Keypad NumLk & NumLk & ScrLk Keys ScrLk Keys 3.
1 Quick Start Guide Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed (see “Hot Key” on page 4 - 6). When the driver is installed, an icon will appear in the taskbar. Keys Function Keys Function Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display Toggle 3.
Quick Start Guide System Map: Front & Rear Views 1 3 1 2 4 5 Figure 1 - 4 Front & Rear Views 1. 2. 6 3. 4. 5. 6. 7 7.
1 Quick Start Guide Figure 1 - 5 Left & Right Views 1. 2. 3. 4. 5. 6. 7. 8. DC-In Jack RJ-45 LAN Jack External Monitor Port Vent/Fan Intake/ Outlet 3 * USB 2.0 Ports Optical Device Drive Bay (for CD/ DVD Device - see page 2 - 3) RJ-11 Phone Jack Security Lock Slot System Map: Left & Right Views 1 2 3 4 6 5 5 5 7 8 Overheating To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use.
Quick Start Guide Disk Eject Warning Changing DVD Regional Codes Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice. Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.
1 Quick Start Guide Figure 1 - 6 Bottom View 1. 2. 3. Battery Hard Disk Bay Cover (3.5G Module Location) RAM & CPU Bay Cover System Map: Bottom View 1 CPU 2 The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 3 Overheating To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
Quick Start Guide Windows Vista Start Menu & Control Panel Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
1 Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display Settings control panel (in Personalization) in Windows Vista as long as the appropriate Intel video driver is installed. For more detailed video information see “Intel Video Driver Controls” on page B - 1. To access Display Properties in Windows Vista: 1. 2. 3. 4. 5. 6. 7. Click Start, and click Control Panel (or point to Settings and click Control Panel).
Quick Start Guide 1 2 4 3 Figure 1 - 8 - Display Properties Desktop Intel Display Mode Description Single Mode One of the connected displays is used as the display device Intel(R) Dual Display Clone Mode Both connected displays output the same view and may be configured independently Extended Desktop Mode Both connected displays are treated as separate devices, and act as a virtual desktop Table 1 - 6 - Display Options Video Features 1 - 17 1
1 Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 15) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • Hard Disk Drive Optical (CD/DVD) Device 7-in-1 Card Reader ExpressCard Slot TouchPad and Buttons/Mouse Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location 2 - 2 Hard Disk Drive Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 14).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 13. .
Features & Components 2 Card Reader Cover Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “CardReader” on page 4 - 5).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). Make sure you install the Card Reader driver (see “CardReader” on page 4 - 5). ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34.
Features & Components 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Features & Components Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon to bring up an audio menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination. Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer).
Features & Components 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack on the left of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Sleep/Hibernate hotkey button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down). Use Power Options (Hardware and Sound menu) control panel in Windows Vista to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance for maximum performance when the computer is powered from an AC power source.
Power Management 3 Power Button The Power Button in the Start Menu (in Classic View use the Shut Down button ) can be used to send the computer into a powersaving state. Sleep Mode & Mobile PC Battery A mobile PC in Sleep uses very little battery power. After an extended period of time the computer will save any open documents and applications to hard disk. Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. It is recommended that you enable a password on wake up in order to protect your data. However you can disable this setting from the Power Options menu by clicking Require a password on wakeup in the left menu, and selecting the options (click Change settings that are currently unavailable).
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Power Status Icon To Resume Color Power Off Off Press the Power Button Sleep Blinking Green Press the Power Button Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Power Management 3 Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Please follow these simple guidelines to get the best use out of your battery. Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g.
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. • Reduce the amount of time before the display is turned off. • Close wireless, Bluetooth, modem or communication applications when they are not being used.
Power Management Battery Life 3 Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 3. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 14 for instructions on how to do this).
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Caution Danger of explosion if battery is incorrectly replaced. Damaged Battery Warning Should you notice any physical defects (e.g.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 3 1. 2. 3. Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click Install Drivers (button). 2. 4 If you wish to install the drivers manually see overleaf for the driver path information. 3. Check the driver installation order from Table , on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Drivers & Utilities Driver Page Driver Location Note Manual Driver Installation Video Page 4 - 5 Vista 64bit: X:\Drivers\Video\vista64\Setup.exe Audio Page 4 - 5 Vista 64bit: X:\Drivers\Audio\Setup.exe Modem Page 4 - 5 Vista 64bit: X:\Drivers\Modem\ssetup.exe LAN Page 4 - 5 Vista 64bit: X:\Drivers\Lan\setup.exe TouchPad Page 4 - 5 Vista 64bit: X:\Drivers\TouchPad\Setup.exe CardReader Page 4 - 5 Vista 64bit: X:\Drivers\CardReader\Setup.
Drivers & Utilities 4 Updating/Reinstalling Individual Drivers User Account Control (Win Vista) If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer).
Drivers & Utilities Driver Installation Procedure Video 1. Click 1.Install Video Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. Audio 1. Click 2.Install Audio Driver > Yes. 2. Click Next. 3. Click Finish to restart the computer. Modem 1. Click 3.Install Modem Driver > Yes. 2. Click OK. 3. The modem is ready for dial-up configuration.
Drivers & Utilities 4 Fingerprint Reader Module PC Camera Module See the introduction in “Fingerprint Reader Module” on page 7 - 3, and check the installation procedure. See the introduction in “PC Camera Module” on page 7 - 16, and check the installation procedure. Hot Key 1. Click 7.Install Hotkey Driver > Yes. 2. Click Next > Install. 3. Click Finish > Finish to restart the computer. Trusted Platform Module Bluetooth Module See the introduction in “3.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured right is for guideline purposes only. The POST screen on your computer may appear slightly different. If you disable the Boottime Diagnostic Screen, the POST screen will not appear. The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu Phoenix TrustedCore(tm) Setup Utility Figure 5 - 2 Main Main Advanced Security Boot Exit Main Menu Item Specific Help 5 BIOS Revision ******** System Time: System Date: [22:12:05] [06/12/2007] IDE Primary/Master IDE Secondary/Master [FUJITSU MHW2060BH-(S1)] [Optiarc CD-RW CRX880A-(SM] System Memory Extended Memory 640 KB 1038336 KB F1 Esc Help Exit Select Item Select Menu -/+ Enter , , or selects field.
BIOS Utilities IDE Primary/Master (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a HDD on the computer’s IDE Primary/Master Channel. Use the Auto (Type:) setting to have the items configured automatically for you. IDE Secondary/Master (Main Menu) Pressing Enter opens the sub-menu to show the configuration of an optical Device on the computer’s IDE Channel 1. Use the Auto (Type:) setting to have the items configured automatically for you.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu Phoenix TrustedCore(tm) Setup Utility Advanced Advanced Main Security Boot Exit Item Specific Help Reset Configuration Data: Local Bus IDE adapter: 5 [No] [Both] Boot-time Diagnostic Screen: Legacy USB Support: USB 2.
BIOS Utilities Local Bus IDE adapter: (Advanced Menu) This item allows you to configure the IDE bus which controls the hard disk and optical devices. It is set to “Both” by default. Boot-time Diagnostic Screen: (Advanced Menu) Use this menu item to enable/disable the Boot-time Diagnostic Screen. 5 Legacy USB Support: (Advanced Menu) Use this menu item to enable/disable the support for Legacy Universal Serial Bus. USB 2.0 Enable: This menu item can be used to enable/disable support for USB 2.0.
BIOS Utilities Security Menu 5 Security Menu Phoenix TrustedCore(tm) Setup Utility Main Figure 5 - 4 5 - 10 Security Menu Security Security Boot Exit Item Specific Help The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
BIOS Utilities Password on boot: (Security Menu) Specify whether or not a password should be entered to boot the computer (you may only set a password on boot if a supervisor password is enabled). If “Enabled” is selected, only users who enter a correct password can boot the system (see the warning in the sidebar). The default setting is “Disabled”.
BIOS Utilities TPM State Menu 5 To access this menu you must first enable TPM support from the security menu (see page 5 - 11).
BIOS Utilities If you have made any changes to the TPM State you will be asked to execute or reject the changes made after you have saved and exited the BIOS. Highlight the required option (it will be white), and then press Enter to save it. Phoenix TrustedCore(tm) Setup Utility Physical Presence operations Figure 5 - 6 Item Specific Help TPM configuration change was requested to State: Clear WARNING!!! Clearing erases information stored on the TPM.
BIOS Utilities Boot Menu Phoenix TrustedCore(tm) Setup Utility Figure 5 - 7 Main Advanced Security Boot Exit Boot Menu Item Specific Help Boot priority order: 1: USB FDC: 2: IDE CD: Optiarc CD-RW CRX880A-(SM) 3: IDE HDD: FUJITSU MHW2060BH PL-(S1) 4: USB HDD: 5: PCI BEV: Realtek Boot Agent 6: 7: 8: Excluded from boot order: : USB KEY: : USB CDROM: : USB ZIP: : 1394 CDROM: 5 F1 Esc Help Exit Select Item Select Menu -/+ Enter Keys used to view or configure devices: Up and Down arrows sele
BIOS Utilities Exit Menu Figure 5 - 8 Phoenix TrustedCore(tm) Setup Utility Main Advanced Security Boot Exit Exit Menu Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Utilities 5 5 - 16
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 .
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 5. 6. 7. Lift the hard disk up in the direction of arrow 5 . Remove the screws 6 & 7 and cover 8 . Reverse the process to install a new hard disk drive.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Locate the RAM & CPU bay cover and remove screws 1 - 4 . Remove the screw at point 5 , and use a screwdriver to carefully push out the optical device at point 5 . Reverse the process to install the new device.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SODIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 for details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer. 1. 2. Turn off the computer, and turn it over and remove the battery. Locate the RAM & CPU bay cover and remove screws 1 - 4 .
Upgrading The Computer 3. Figure 6 - 6 4. Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 5 , and remove the cover 6 . CPU/RAM Bay Cover Removed 6 6 Contact Warning Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. 5 5.
Upgrading The Computer 6. The RAM module will 9 pop-up, and you can remove it. Figure 6 - 8 RAM Module Removal 9 6 7. 8. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. 9. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure. 10.
Upgrading The Computer Warranty The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 6 Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • • • • • • Fingerprint Reader Module Bluetooth Module Wireless LAN Module PC Camera Module Trusted Platform Module 3.
Modules & Options Password Warning If you set passwords for any of the security modules, NEVER forget your password. 7 The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Modules & Options Fingerprint Reader Module If you have included the fingerprint reader in your purchase option you will need to install the driver as per the instructions below. Help & Manual Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. Right-click the taskbar icon to bring up the menu to select Help. Before beginning the enrollment process it is recommended that you go through the fingerprint tutorial.
Modules & Options User Enrollment 1. 2. 3. 7 Click Start > Programs/All Programs > Protector Suite QL > User Enrollment, or double click the taskbar icon . On the first run of the program you will be asked to click the button to accept the license, and then click OK. Click Next and select “Enrollment to the hard disk”, and click Finish. Figure 7 - 1 Enroll to Hard Disk 4. 5. 6. 7. 8.
Modules & Options 9. 10. 11. 12. 13. 14. Click the button above any of the fingers to begin the enrollment process for that finger. Swipe the finger three times to enroll that finger. Repeat the process for all the fingers you wish to enroll (see sidebar), and then click Next. Click Finish. Click any of the headings under “Learn more about:” to get more information on any topic. Click Close.
Modules & Options the Control Center etc. from the Protector Suite QL item in the Programs/All Programs menu. Figure 7 - 3 Control Center & Biomenu 7 17. See “Help & Manual” on page 7 - 3 for further details. 18. If you swipe your finger over the reader at any time you can access the Biomenu to lock the computer, register websites, open the Control Center and access the Help menu. 19. The Control Center allows you to change the Settings, enroll Fingerprints and get Help.
Modules & Options Bluetooth Module Before installing the Bluetooth driver, make sure that the optional Bluetooth module is on. Use the Fn + F12 key combination (see “Function/Hot Key Indicators” on page 1 - 10) to toggle power to the Bluetooth module. Make sure you install the drivers in the order indicated in Table , on page 4 - 3. Bluetooth Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual CD-ROM (Win Vista) into the CD/DVD drive. 2. Click Install Option Drivers (button). 3.
Modules & Options User Guides & Help View the BlueSoleil User Guides from the Help Menu (or press the F1 key) in the IVT Corporation BlueSoleil Main Window control panel. 7 Click the Help menu and select Contents and Index. Look through Getting Started or select the appropriate User Guide from the Contents menu.
Modules & Options Bluetooth Local Area Connection You can check the Bluetooth connection status from the Network and Sharing Center: 1. 2. 3. 4. 5. 6. Use the Fn + F12 key combination to turn on the Bluetooth module. Run the IVT Corporation BlueSoleil program from the desktop icon or Start menu. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Network and Sharing Center (Network and Internet). Click Manage network connections.
Modules & Options 8. 9. 7 Figure 7 - 6 Bluetooth Disconnected 7 - 10 Bluetooth Module Do not use the close button or Fn + F12 key combination before clicking File > Exit or the correct status will not be displayed. You can then use the Fn + F12 key combination to turn off the Bluetooth module (check the LED icon for the Bluetooth module power status).
Modules & Options Wireless LAN Module If you have included an Intel PRO/Wireless 3945ABG (802.11a/b/g) or Intel PRO/ Wireless 4965ABN (802.11a/g/n) PCIe WLAN module in your purchase option, make sure that the Wireless LAN module is on before installing the driver. Use the Fn + F11 key combination (see “Function/Hot Key Indicators” on page 1 - 10) to toggle power to the Wireless LAN module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3.
Modules & Options Connecting to a Wireless Network Make sure the Wireless LAN module is turned on. 1. Click the taskbar wireless icon , and then click Connect to a network (or rightclick the icon , and then click Connect to a network). Figure 7 - 7 Taskbar Menus Click icon Right-click icon 7 Network and Sharing Center 2. 3. In the Show list, click to choose Wireless from the drop-down menu. A list of currently available networks will appear.
Modules & Options 4. 5. Click a network, and then click Connect. If you do not see a network you want to connect to, click Set up a connection or network (a list of options will appear allowing manual searching, and creating a new network). Figure 7 - 9 Connecting 7 6. Move the cursor over the taskbar icon to see the connection status (see below).
Modules & Options 7. Security Enabled Networks To disconnect from the wireless network you can click the taskbar wireless icon , and then select Connect or disconnect to access the network menu, and click Disconnect (or right-click the icon , and then click Disconnect from). You should try to make sure that any network you are connecting to is a secure network. 7 Click icon Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules & Options Latest PC Camera Driver Information 7 Check the CD, and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here. PC Camera Module There are 2 camera options available for this computer, depending on your purchase configuration. The 1.3M pixel camera module uses the BisonCap application, and the 2.0M pixel camera module uses the Video View application, to capture video files.
Modules & Options PC Camera Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual CD-ROM (Win Vista) into the CD/DVD drive. 2. Click Install Option Drivers (button). 3. Click 3.Install Camera Driver > Yes. For the 1.3M Pixel Camera Module: 1. Choose the language you prefer and click OK > Next > Next. 2. Click Finish to restart the computer. 3.
Modules & Options PC Camera Audio Setup (all camera modules) If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 7 Click Start, and click Control Panel (or point to Settings and click Control Panel). 2. Click Sound (Hardware and Sound). 3. Click Recording (tab). 4. Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled. 5. Double-click Microphone (or select Properties from the right-click menu).