HD IR Bullet Network Camera Quick Start Guide Version 1.0.
Welcome Thank you for purchasing our Network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference! Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. Please check if the power supply is correct before operating the device.
. Operation and Daily Maintenance Please do not touch the heat dissipation component of the device directly in order to avoid scald. Please do not dismantle the device; there is no component which can be fixed by users themselves in the machine. It may cause water leakage or bad image for the device due to unprofessional dismantling. Please contact after-sale service to replace desiccant if it becomes green.
Please contact the customer service for the latest procedure and supplementary documentation. There may be deviation between the actual value of some data and the value provided in the manual due to the reasons such as the real environment is not stable and so on. Please refer to the company’s final explanation if there is any doubt or dispute. The company is not liable for any loss caused by the operation which is not followed by the manual. FCC Information 1.
Table of Contents 1 Device Structure ......................................................................................................................... 1 1.1 Device External Cable ................................................................................................. 1 1.2 Framework and Dimension ......................................................................................... 2 1.3 Alarm Setup....................................................................................
1 Device Structure 1.1 Device External Cable Note: The following figure is for reference only, which is used to know the function of cable port. There are differences about cable structure between different models, please refer to the actual product for more details. You can refer to the following figure for cable information. See Figure 1-1. Figure 1-1 Please refer to Table 1-1 for detailed information. No.
No. Port Name Function Connector Function Description Input DC 12V or AC 24V, please be sure to power the device according to the label instruction when using the device. 5 Power input port Power Note / Please use round port to 2PIN converter cable when using AC 24V for power supply. Caution It may cause damage to the device if it fails to power the device according to the device label. Table 1-1 Please refer to Table 1-2 for detailed pin information.
1.3 Alarm Setup Note: It is only supported by some series products. Figure 1-3 Alarm input, output description: Step 1 Connect alarm input device to the alarm input of I/O port cable. Step 2 Connect alarm output device to the ALARM_OUT and ALARM_OUT_GND of I/O port cable, Alarm output is the relay switch output; alarm output port can only be connected to NO (normally open) alarm device. Step 3 Open the WEB, set alarm input and output correspondingly in alarm setup.
Figure 1-4 Please refer to the following figure for alarm output information. See Figure 1-5 and Figure 1-6. Figure 1-5 Figure 1-6 Mode A: Level application. Alarm output high and low level, alarm output is OC; it needs to increase pullup resistance externally to work normally. Max external pull-up level is 12V, max port current is 300mA (peak).
2 Device Installation Note Please make sure the installation surface can support at least 3X weight of the camera and the bracket. Please cut off the device power before installing Micro SD card. Figure 2-1 Step 1 SD card installation (Optional) Note It needs to implement the step when the device is equipped with Micro SD card slot and it needs to use Micro SD card. 1. Loosen the screw on the lower cover.
Figure 2-2 Note: Motorized vari-focal series devices are equipped with motorized lens by default, which doesn’t need manual adjustment; meanwhile the devices with two direction buttons support zoom and focus via the two direction buttons on the panel. You can connect the analog output port to the TV monitor to check image via analog output cable. Press the reset button for 4 to 5 seconds to realize reset function for the device. 3.
It needs to implement the step when the device is equipped with waterproof connector and it is used outdoors. Figure 2-3 1. Keep the convex groove outward and install the rubber ring into the network port, keep the smaller hole of the rubber ring outward and install the fixing rubber ring into the main body of the waterproof connector. 2.
Figure 2-4 1. Use screwdriver to loosen adjusting screw. 2. Adjust the device in all possible directions, and set its monitoring direction according to use requirement. 3. Use screwdriver to tighten the adjusting screws.
3 Network Configuration The IP address of all the cameras is the same when leaving factory (default IP 192.168.1.108). To make the camera access to the network smoothly, please plan the available IP segment reasonably according to the actual network environment. 3.1 Modify IP Address The cameras which are accessed via wired network can acquire and modify the IP address through "Quick Configuration Tool". This section introduces the approach of modifying IP address via "Quick Configuration Tool".
Figure 3-2 Step 5 Set the mode as Static, and input the planned Start IP, Subnet Mask and Gateway. Note Set the mode as DHCP when there is DHCP server in the network, the device will automatically acquire IP address from the DHCP server. Step 6 Click OK to finish modification. 3.
Figure 3-3 Step 2 Input username and password, click Login. The system will pop out WEB main interface. Note The default username and password is admin and admin respectively, please modify the administrator password as soon as possible after you successfully logged in. Step 3 Click Here to Download Plug-in, and then install controls according to the system prompt. See Figure 3-4 or the WEB main interface.
Note: This quick start guide is for reference only. Slight difference may be found in user interface. All the designs and software here are subject to change without prior written notice. If there is any uncertainty or controversy, please refer to the final explanation of us. Please visit our website or contact your local service engineer for more information.
