CSC600ER; XL-2055ER USER'S MANUAL
TABLE OF CONTENTS FEATURE LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . 2 2. The switch will be set to the OFF position and the volume will be set to middle at factory. 3. Please adjust the volume to your necessary. Too loud volume may hurt your ear. We recommend you first move the switch to the OFF position. SETTING UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BASIC FUNCTION . . . . . . . . . . . .
AMPLIFY FEATURE Receiver Voice Tone The unit provides extra amplification in the tone frequency range you need to boost. You can identify the range follow these steps: First, move the switch on the rear of the unit to ON or OFF position to turn the function on or off. See Figure1. Then: 1. If you move the switch to ON position, each time you use the phone, the amplifier turns on automatically, then you can adjust the tone frequency range while on a call by moving the TONE control. See Figure2.
TROUBLESHOOTING SAFETY INSTRUCTIONS To reduce the risk of fire, electrical shock, and injury, please follow these basic safety precautions before you use this equipment. 1. Carefully read the instructions in this manual. 2. Follow all warnings and instructions marked on the unit. 3. When cleaning, unplug the telephone jack from the wall outlet. Use a damp cloth. DO NOT use liquid or aerosol cleaners. 4.
CALLER ID ON CALL WAITING When you subscribe to Caller ID/Call Waiting service from your local telephone company and you activate the call waiting function, the telephone will display the name and number of the second caller while you are having a conversation. Caller ID info displayed Caller two's information is displayed Caller 1 436-1234 Caller 1 4 Caller 2 291-5678 1. When you are on the line, the telephone will display the name and number of the second caller.
WALL INSTALLATION The phone can be mounted to any wall surface using two self-tapping screws (not supplied). Follow the instructions. 1. Install the two self-tapping screws at a distance of 80mm from each other and located on a vertical centre line (See Figure 1). Desk use position 8.0cm Wall mounting use position If the incoming call number is of 10 or 11 digits, when you press s or t button to review it, you can press # button to switch this number between 10 digits and 11 digits.
CALLER ID SYSTEM OPERATION LOCATION OF CONTROLS Subscription to Caller ID service from your local phone company is required. l New calls / Messages waiting indicator - The red indicator light will flash to indicate that you have new calls/messages and it will flash until all the new calls / messages have been reviewed. 3 2 4 5 1 Review Your Caller ID Records - Use the s or t button to scroll through the caller ID list.
PRIVATE - If the caller has exercised the option to prevent his name and number from being sent, "PRIVATE" will be shown on the screen. Outgoing speech volume select switch NO CALLS - When all calls have been deleted, the display will show NO CALL. Ring Volume Control END OF LIST - This message is displayed when you use the s or t button to reach the top (end) of the caller ID list. If there are no calls, then LCD shows NO CALL.
RECEIVING CALL RECORDS A caller ID record consists of the following information: Time and Date Battery Indicator Number of Calls The serial number of caller list Caller's number Caller's name Remote register button *This function should be supported by your local telephone company.
BASIC FUNCTION 1. Redial function This feature allows you to redial the last number you have called by one-touch operation. a. Lift handset or press the SPEAKER button to get a dial tone. b. Press the REDIAL button to redial the last number called. 2. Flash function Press the CALL WAITING button to terminate a call and institute a dialling tone for another call or to get another call from "Call Waiting" (a special telephone service).
NOTES: 1. In the message, you should tell the helper to press one of the special buttons (0~9,*,#) to confirm that your SOS message has been received. 2. If you want to record a message for less than 10 seconds, you can press the DIAL button to confirm and exit. b. To play the SOS message Press the s or t button to select PLAY SOUND menu and press the DIAL button to play the SOS message. After setting the SOS number and message, you can use the function conveniently whenever.
10. Delete a single or all record number(s) Find out the number which you want to remove, press DELETE button, the LCD will show DEL ? and then press DELETE button again to remove this number. If you press and hold DELETE button for about 6 seconds, the LCD will show ALL DEL ? then press the DELETE button to remove all numbers and the LCD will show NO CALL. In the state of on-hook, * Press the s or t button to select the Caller ID numbers.
Use the s or t button to select the language you want and press the DIAL button to confirm. Press the DELETE button to return to the previous menu. LCD contrast -- Use the s or t button to select the LCD contrast level you want. Press the DIAL button to confirm and exit. Set Area & LDS -- When you use this phone for the first time, or move to an area that has different area code, you must enter your area code.
c. When the number and name setting is completed, press and hold the DIAL button to store it. Meanwhile enter the next number's presetting. Then you can press the DELETE button to return to standby mode. 2.To review/delete/speed dial/modify the phone book number Select the REVIEW menu and press the DIAL button to confirm. a. To review the phone book number: Use the s or t button to review the phone book entries.
Customer Information 1. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On bottom of this equipment is a label that contains, among other information, a product identifier of [US: CLSTE12BCSC600ER]. If requested, this number must be provided to the telephone company. 2.
FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.