XAP IR Remote Control Installation & Operation Manual ClearOne Communications, Inc.
ii Table of Contents Table of Contents 1 Introduction Introduction Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Professional Services Group . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Introduction Sales and Customer Service 3 Installation Installation Telephone: 1.800.945.7730 (USA) or 1.801.975.7200 Fax: 1.800.933.5107 (USA) or 1.801.977.0087 E-mail: sales@clearone.com XAP IR Remote Receiver Installation is simple. Plug the XAP IR Remote Receiver into the RS-485 Remote ClearOne Communications EuMEA GmbH Panel A or Remote Panel B connector located on the back of the ClearOne unit. Leonhardstr.
Installation Telephone Set MUTE IN USE XAP IR Receiver OUTPUT 6 OUTPUT 7 OUTPUT 8 INPUT 5 INPUT 6 INPUT 7 INPUT 8 OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 MIC 1 There are three LEDs on the front of the XAP IR Remote—Mute, In Use, and • Mute. The Mute LED flashes red when microphones are muted (default). You can program this LED to illuminate to another command in the Remote Builder window of G-Ware. See Configuration (below) for more information. SPEAKER OUTPUT 5 Front Panel LEDs Ready.
6 Configuration Configuring G-Ware Remote Builder 1. Open the Remote Builder window in G-Ware by clicking the Remote Builder Flow Screen button or Remote Builder toolbar button. Configuration 7 6. Click the Active Command or Inactive Command button to set the command for operation when the button is active or inactive. 7. Select the Device Type, ID, and Command from their respective lists. When you select a command, a description of it appears in the Command Description box. Figure 6.
8 Configuration To configure speed dial numbers 9 2. Select the remote ID number of the remote you want to program from the Select Remote ID list and IR Remote from the Select Remote Type dropdown lists. 1. Click the Dial button in the G-Ware Flow Screen. The Dial window opens. 3. Select the Volume Up button from the Select Button/LED list. You can also select the button by clicking directly on the Volume Up button in the remote control depiction. 2. Click Edit in the Speed Dial section.
10 Configuration Configuration 11 Programming Example B This example illustrates how to configure the remote control to mute all mics on multiple connected units (in this case, a XAP 400 with a device ID of 0 and a XAP 800). In this example, the XAP IR Remote receiver is connected to the XAP 400. For the XAP 800: 5 * Mute * M 1 To mute multiple units The unmute macro has the following command lines: For the XAP 400: 7 * Mute * M 0 For the XAP 800: 5 * Mute * M 0 2.
12 Operation 13 Operation Remote Control Buttons Operation While within 25–40 feet of the receiver, point the remote control toward the receiver and press the buttons to operate. Getting Started Once your remote is connected to your XAP system, you have configured it, and the To place a call Ready LED is lit, you can start using your remote control. 1. Press Telephone On (green) button. The In Use LED illuminates. Operation is easy and straightforward.
14 Operation Please consult your PBX owner’s manual for specific requirements of your individual phone system. G-Ware can be used to adjust the hook flash duration to match 15 Specifications Specifications your PBX. This setting is located in the Telco Config window in G-Ware. To redial the last telephone number dialed · Press the Redial button. REDIAL To dial a number stored in speed dial · Press the Speed Dial button.
16 Compliance 17 Compliance NO OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR USE, APPLIES TO THE PRODUCT. MANUFACTURER’S MAXIMUM LIABILITY HEREUNDER SHALL BE THE AMOUNT PAID BY THE END-USER FOR THE PRODUCT. No person or entity authorized to assume any obligation or other liability in connection with the products.
18 19 Index Index B G buttons 14 G-Ware 6-11 Conference Call 14 Flash 13 I Mute Off 13 In Use LED 5, 13 Mute On 13 installation 3 number 13 M Off 13 Mute LED 5, 13 On 13 Program 14 O Redial 14 Operation 12 Speed Dial 14 Volume Down 13 P Volume Up 13 programming 5 C R ClearOne’s Conference Call services 14 Ready LED 5 configuration 5 S D Speed dial 7, 8, 13, 14 DIP switches 4 Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760 Technical Services Group ~ 1-800-2