ENGLISH A.LEDA WASH K10 CC - A.LEDA WASH K10 W A.LEDA WASH K10 TW - A.LEDA WASH K20 CC A.LEDA WASH K20 W - A.
SAFETY INFORMATION EN • Installation Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used, it needs to be replaced with a genuine spare.
LiFePO4 Pb • Battery This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. Disposing This product is supplied in compliance with European Directive 2012/19/EU - Waste Electrical and Electronic Equipment (WEEE). To preserve the environment please dispose/recycle this product at the end of its life according to the local regulation.
IT INFORMAZIONI DI SICUREZZA • Installazione Assicurarsi che tutte le parti per il fissaggio del proiettore siano in buona condizione. Assicurarsi della stabilità del punto di ancoraggio prima di posizionare il proiettore. La fune di sicurezza, debitamente agganciata all’apparecchio e fissata alla struttura di sostegno, deve essere installata in modo che, in caso di cedimento del sistema di supporto primario, si abbia la minor caduta possibile dell’apparecchio.
LiFePO4 Pb • Batteria Questo prodotto contiene una batteria ricaricabile piombo-acido o Litio Ferro Tetrafosfato. A tutela dell'ambiente si prega di smaltire la batteria a fine vita in conformità alla normativa vigente. Smaltimento Questo dispositivo è conforme alla Direttiva Europea 2012/19/UE - Rifiuti di apparecchiature elettriche ed elettroniche (RAEE). Nel rispetto dell'ambiente, smaltire/riciclare il prodotto al termine del suo ciclo di vita secondo le disposizioni di legge locali.
FR CONSIGNES DE SÉCURITÉ • Installation S’assurer que toutes les pièces pour la fixation du projecteur sont en bon état. S’assurer de la stabilité du point d’ancrage avant de positionner le projecteur. Le câble de sécurité, à fixer correctement à l’appareil et à la structure de support, doit être installé de façon à ce que, en cas de rupture du système de support principal, la chute de l’appareil soit la plus limitée possible.
LiFePO4 Pb • Batterie Ce produit contient une batterie rechargeable au plomb-acide ou tétraphosphate de fer au lithium. Une fois la batterie arrivée à la fin de sa durée de vie, procéder à son élimination conformément à la norme en vigueur de manière à éviter toute pollution. Élimination Ce dispositif est conforme à la Directive Européenne 2012/19/UE – Déchets d’équipements électriques et électroniques (DEEE).
DE INFORMATIONEN ZUR SICHERHEIT • Installation Sicherstellen, dass alle Teile für die Befestigung des Projektors in einwandfreiem Zustand sind. Vor der Installation des Projektors die Stabilität der Verankerungsstelle überprüfen. Das korrekt am Gerät eingehakte und an der Haltestruktur befestigte Sicherheitsseil muss so installiert werden, dass bei einem Nachgeben der Haupthalterung die Fallhöhe des Gerätes so gering wie möglich ist.
LiFePO4 Pb • Batterie Dieses Produkt enthält eine wiederaufladbare Blei-Säure-Batterie oder Lithium-Eisen-tetraphosphat. Zum Schutz der Umwelt bitten wir Sie, diese Batterie, nachdem sie verbraucht ist, gemäß den geltenden Vorschriften zu entsorgen. Entsorgung Diese Vorrichtung entspricht der Europäischen Richtlinie 2012/19/UE - Abfall von elektrischen und elektronischen Gerätschaften (RAEE).
ES INFORMACIONES DE SEGURIDAD • Instalación Asegúrese de que todos los elementos de fijación del proyector estén en buenas condiciones. Controle la estabilidad del punto de anclaje antes de instalar el proyector. La cuerda de seguridad, correctamente enganchada al aparato y fijada a la estructura de soporte, debe colocarse de modo que, si el soporte principal cede, el aparato sufra la menor caída posible. En caso de desgaste de la cuerda de seguridad, sustitúyala por el recambio original.
LiFePO4 Pb • Batería Este producto contiene una batería recargable plomo-ácido o de litio tetrafosfato Hierro. Para proteger el ambiente se ruega eliminar la batería conforme a la normativa vigente. Eliminación Este dispositivo es conforme a la Directiva Europea 2012/19/UE - Residuos de equipos eléctricos y electrónicos (RAEE).
UNPACKING AND PREPARATION 1 K10 W A WASH K20 CC CC - A.LED WASH K10 TW - A.LEDA WASH K20 TW A.LEDA WASH K10 W - A.LEDA WASH A.LEDA WASH K20 A.LEDA ENGLISH ® INSTR UCTIO PR IST00D/001 C61408 C61407 C61406 C61413 C61412 C61411 L N MANUA Y AR IMIN EL product! a Clay Paky choosing ations on the rich Clay Congratul custom.
INSTALLATION AND START-UP 3 Installing the projector - Fig. 3 The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.
CONTROL PANEL 5 Mains Connecting to the mains supply - Fig. 5 6 DMX 512 5 PIN 5 4 3 1 2 SCREEN SIGNAL SIGNAL Connecting to the control signal line (DMX) - Fig. 6 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 5-pin male/female connectors.
8 28 28 Reversal of the display - Fig. 8 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512). The address can also be set with the projector switched off.
MENU SETTING 1 2 Dmx Address Set Up 3 Option Pan / Tilt Invert Pan Information Invert Tilt Fixture ID System Errors Fixture Hours Swap Pan-Tilt Led Energy tot Encoder Pan-Tilt Silent Mode Option System Version Standard Board Diagnost.
NOTE: On grey the default options Set Up Dmx Address SET UP MENU DMX ADDRESS NOTE: without the DMX signal the Address (XXX) flashing Allows you to select the DMX ADDRESS. 1) Press - the current DMX Adress appear on the display. and DOWN , RIGHT keys to plan the DMX 2) Use the UP Address. 3) Press to confirm the selection or LEFT to keep current settings. Address xxx F B C E D F Fixture ID FIXTURE ID Allows you to select the FIXTURE ID. 1) Press - the current Fixture ID appear on the display.
Special Functions SPECIAL FUNCTIONS Pan / Tilt speed Lets you select two different Pan and Tilt speeds. - the current setting appears on the display. 1) Press and DOWN keys to select one of the following 2) Use the UP settings: - Normal - Fast to confirm the selection or LEFT to keep current 3) Press settings. Pan / Tilt speed F B C F D Dimmer Curve Lets you select four different Dimmer channel curves. - the current setting appears on the display.
OPTION Invert Pan Invert Tilt Swap Pan-Tilt Encoder Pan-Tilt Silent Mode Display Pan/Tilt speed Dimmer Curve RGB Gamma DEFAULT Off Off Off On Standard Off Normal Curve 3 Gamma 2.0 INFORMATION MENU Information SYSTEM ERRORS Shows a list of warnings and messages relevant to errors occurred since the fixtures switching-on. you are allowed to reset the SYSTEM ERRORS list. 1) Pressing A confirmation message (Are you sure you want to clear error list ?) appears on the display.
MANUAL CONTROL Manual Control RESET Used for resetting the projector. to reset the projectors, a confirmation message (Are you 1) Press sure ?) appears on the display. 2) Select YES to starting reset the fixture or NO to keep the current setting and return to the top menu level. No Reset Yes F CHANNEL Used for setting channel levels from the projector control panel. - the first channel appears on the display.
9 2 1 3 6 5 4 Battery removal - Fig. 9 This product contains a rechargeable lithium iron tetraphosphate. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. LiFePO4 A.
MAINTENANCE 10 3 4 1 2 Opening the covers - Fig. 10 11 4 3 1 2 Removing/Assembling the lens unit - Fig. 11 NB: Apply Loctite 222 (p/n COL002) to the threads of the 3 screws (1) before tightening them. A torque of 0.3N is recommended in order to avoid damaging the zoom movement actuators. A.
12 2 1 Replacing the line actuator - Fig. 12 NB: It is highly recommended to use the DIM002/001 (1) template whenever it is necessary to replace one of the three Zoom movement line actuators. DIM002/001 ensures the actuator group is centred correctly on the lens plate before tightening the 2 screws (2) that fasten the actuator in place. A.
OPTIONAL ACCESSORIES A.LEDA WASH K10 CC TW W 13 C61455 C61456 1 2 3 Cover - Fig. 13 C61455 - Transparent cover (standard) C61456 - Frosted cover A.LEDA WASH K20 CC TW W 14 C61458 C61459 1 2 3 Cover - Fig. 14 C61458 - Transparent cover (standard) C61459 - Frosted cover A.
TECHNICAL INFORMATION 290 (11.42") Power supplies available 100-240V 50/60Hz 250 (9.84") 160 (6.30") Input power • K20 - 750VA • K10 - 450VA 360 (14.17") 423 (16.65") Total output • K10 CC - Max 5300 lumens • K10 TW - Max 6800 lumens • K10 W - Max 10500 lumens • K20 CC - Max 10900 lumens • K20 TW - Max 14300 lumens • K20 W - Max 21700 lumens 479 (18.86") LED source Osram Ostar RGBW LED - 15W Average LED life: 50.000 h 358 (14.09") 253 (9.
NB: To prevent accidental breakage of the effects, which could collide with each other during transport, before switching the projector OFF check that all the projector Channels have been excluded (DMX level @0 bit). A.LEDA WASH K10 CC CHANNEL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CHANNEL MODE Red RedFine Green GreenFine Blue BlueFine White WhiteFine CTO Macro Colour Strobe Dimmer Dimmer fine Pan Pan fine Tilt Tilt fine Function Reset Zoom A.
NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 128 bit - Tilt 128 bit) all the others channels stay at 0 bit. • C.T.O. - COOL WHITE - WARM WHITE • RED - GREEN - BLUE - WHITE K10 CC K10 TW K20 CC K20 TW BIT EFFECT 255 MAXIMUM BRIGHTNESS 0 K10 CC K20 CC LED OFF • RED FINE – GREEN FINE – BLUE FINE – WHITE FINE - COOL WHITE FINE WARM WHITE FINE K10 CC K10 TW K20 CC K20 TW BIT EFFECT 255 UPPER BRIGHTNESS 0 LOWER BRIGHTNESS • C.T.O.
• MACRO COLOUR K10 CC K20 CC LEE COLOUR REFERENCE BIT VALUE R G B W 66 255 255 122 255 255 143 0 76 0 255 0 Dark Steel Blue 158 247 89 0 Deep lavender 232 165 58 0 209-255 - White 255 235 208 - Dirty White 255 207 197 Alice Blue 128 191-206 181 Congo Blue 184-190 174 180-183 170 179 169 Lilac Tint 246 208 45 0 175-178 165 Daylight Blue 75 218 90 0 174 164 Flame Red 211 27 2 0 172-173 162 Bastard Amber 227 176 23 0 168-171 158 Deep Or
• PAN Operation with option InvertPan • TILT Operation with option InvertTilt GOff GOff K10 CC K10 W K10 TW K20 CC K20 W K20 TW K10 CC K10 W K10 TW K20 CC K20 W K20 TW BIT 255 BIT 255 0 0 Operation with option InvertPan GOn GOn Operation with option InvertTilt BIT BIT 255 255 0 0 • PAN FINE Operation with option InvertPan • TILT FINE Operation with option InvertTilt GOff GOff BIT BIT K10 CC K10 W K10 TW K20 CC K20 W K20 TW K10 CC K10 W K10 TW K20 CC K20 W K20 TW 255 255 0 0 O
• FUNCTION • RESET BIT 255 K10 CC K10 W K10 TW K20 CC K20 W K20 TW K10 CC K10 W K10 TW K20 CC K20 W K20 TW EFFECT COMPLETE RESET Complete reset is activated passing throug the unused range and staying 5 seconds in complete reset levels 128 127 COMPLETE RESET PAN / TILT RESET Pan / Tilt reset is activated passing throug the unused range and staying 5 seconds in Pan / Tilt reset levels 77 76 PAN / TILT RESET ZOOM RESET Effects reset is activated passing throug the unused range and staying 5 seconds in
A.
IST00D/001 – EN - Rev.A 12/14 CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.