SP1290 900MHz Wireless Combo Speaker with Headphone User’s Manual Please read before using the equipment
INTRODUCTION This 900 MHz wireless combo speaker system with headphone uses the latest wireless technology that enables you to enjoy music and TV sound anywhere inside your home. You can simply connect the system to any audio source such as Radio, TV, VCR, Hi-Fi and CD/MP3/VCD/DVD player. Without complicated wiring and installation with your Audio/Video equipments and rear channel amplifier, the system enables you to enjoy thrilling, lifelike sound in minutes. FEATURES 1.
8. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage. 9. Do not allow anything to rest on the AC/DC adapter cord or AUDIO IN cable. Do not place this product where the cord can be abused by animals or people walking on it. 10. Never push objects of any kind into this product through the cabinet slots as they may touch dangerous voltage points or short cut parts that could result in a risk of fire or electric shock.
COMBO SYSTEM PART LIST DIAGRAMS & NUMBERING A) TRANSMITTER B) SPEAKER RECEIVER C) HEADPHONE RECEIVER D) ACCESSORIES P.
COMBO SYSTEM PART LIST IDENTIFICATION Parts Identification: A: Transmitter 1. Power On/Off Indicator. 2. Audio cable. 3. Charging cable. 4. Channel selector (channel 2-1) 5. DC IN socket. 6. Antenna. B. Speakers 7. Power ON/Off Indicator. 8. Volume control/ Power ON/OFF. 9. Normal/Boost Bass. 10. Auto Scan Button. 11. DC IN socket. 12. Battery Door. 13. Supporting Stands. C. Headphone 14. Volume Control. 15. ON/OFF Control. 16. Battery compartment. 17. Power LED indicator. 18. Auto-Scan Control. 19.
26. Two rechargeable batteries (AAA size). INSTALLATION TRANSMITTER 1. Insert the antenna tube into the antenna wire. 2. Connect the supplied AC/DC power adapter to an electrical wall outlet. 3. Plug the AC/DC power adapter in the DC jack located on the rear of the transmitter. 4. The rear of the transmitter has one audio cord that can be connected to audio output jack of TV, Monitor, VCR, Radio recorder, CD/MP3/VCD/DVD players or to headphone/earphone jack with the connector provided.
WIRELESS HEADPHONE 1. Open the battery compartment cover on the right side of the headphone. 2. Insert 2pcs of AAA size rechargeable batteries (supplied in the package) by matching the + and – on the battery to the diagram inside the battery compartment. 3. Close the battery compartment by sliding the battery compartment cover back into place. OPERATION -Turn on the audio source (TV or audio component) to which the transmitter is connected with. The red LED on the transmitter will light up.
For Speakers 1. Turn on the ON/OFF button on the speakers. Press the “AUTO-SCAN” button to get the best tuning reception in the speakers. When the button is pressed, frequency tuning starts automatically and it stops when a signal is detected. 2. Volume can be adjusted up by tuning the volume knob on the right sides of the speakers to the desired listening level. 3.
and then press the “AUTO-SCAN” button on the headphone again. 4. . Charging the Batteries a) Move the ON/ OFF switch on the headphones to OFF. b) Plug the charging cable on one end into the jack marked CHG at the back of the wireless transmitter (as shown in the picture below). Plug the other end of the charging cable into the jack marked CHG. on the headphones. c) The charging process will start automatically and the power LED on the transmitter will change from red to green. Important: 1.
source for 4 minutes. If the audio signal comes back, the transmitter will turn on automatically. b) Turn off the speaker by tuning the volume control the OFF position. c) Turn off the headphone by switching the On/Off control. TROUBLE SHOOTING NO SOUND - Ensure the AC/DC adapter is fully inserted into the AC outlet and the power connection input on the transmitter. - Ensure the speakers/headphone is switch ON. - Speaker’s battery capacity is low, connect the AC/DC adapter to the speakers.
matching the frequency of the transmitter. - Change the position of the channel selector on the transmitter. Press the “AUTO-SCAN” button on the speaker/headphone. - Ensure the volume level of speakers/headphone is adjusted properly. - The speakers/headphone is too far away from the transmitter, move it closer. - The audio input level of the audio signal is too low. Turn up the volume of the audio source equipment.
TECHNICAL SPECIFICATIONS Transmission Mode : UHF stereo Carrier Frequency : 900 MHz Operation Voltage : Transmitter, DC 12.