4½” Angle Grinder Model CAG122 Part Number 6470127 Operating & Maintenance Instructions © 0111
Specifications Model No ................................................................. CAG 122 Part No ..................................................................... 6470127 Supply Voltage ........................................................ 230 V AC, 50 Hz, 1 Phase Motor input wattage .............................................. 900Watts Fuse Rating ............................................................... 13A Insulation Class ........................................................
Contents Specifications ............................................................................................. 2 Guarantee .................................................................................................. 3 Features and Use ....................................................................................... 3 For your Own Safety ................................................................................... 4 General Safety Precautions : For Power Tools .......................
For Your Own Safety WARNING: As with all machinery, there are certain hazards involved with their operation and use. Exercising respect and caution will considerably lessen the risk of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator or damage to property, may result. Keep children away when using Power Tools. Eye protection manufactured to the current European Safety Standard should be worn when using Power Tools.
Additional Safety Precautions : For Angle Grinders Eye Protection manufactured to the current European Safety Standard should be worn when operating grinding equipment. Ear Protection manufactured to the current European Safety Standard should be worn when operating grinding equipment. worn A Dust Mask manufactured to the current European Safety Standard should be when operating grinding equipment. WARNING ! Ensure all accessories used are rated at the spindle speed, or higher.
Electrical Connections Double Insulated Electrical Appliance This appliance is of Double Insulation Construction. Because of its construction there is no earth required and therefore there is no Earth connection. Connect the mains lead to a standard 230V (50Hz) electrical supply through an approved 13 Amp BS1363 plug, or a suitably fused isolator switch.
Figure (1) Overview 6 2 1 5 4 3 1 Safety ON/OFF Switch 4 Handle 2 Spindle Lock Button 5 Abrasive Disk 3 Moveable Blade Guard 6 Body Before Using the Grinder Fit the Handle : Screw the handle (4) into the appropriate position in the grinder head as required. Figure.1a Adjusting the Guard Adjust the Guard : The guard (3) needs to be adjusted to give maximum protection from sparks and debris produced when grinding. This must be done before mounting the wheel/disk.
(i) Mounting the Grinding Wheel / Cutting Disc 1 Unscrew and remove the outer flange : Lock the spindle by pressing the spindle lock button and use the tool supplied to turn the flange and break the seal. It may then be screwed off by hand. 2 Mount the Grinding Wheel, as shown in Figure 2. The grinding wheel supplied is a ‘Depressed Centre’ type. Mount with the depressed centre towards the motor.
Maintenance IMPORTANT! Ensure that the grinder is disconnected from the power supply before carrying out any maintenance. Before Each Use Always inspect the tool before use, and ensure it is in top condition. Ensure all air vents are clear, use compressed air to clean the tool where possible. (Always wear protective goggles when cleaning with compressed air). Check the power cable to ensure it is sound and not damaged in any way.
Troubleshooting Problem Possible Cause Tool will not operate 1. No supply 1. Check supply and rectify where necessary. 2. Switch is faulty 2. Consult your Clarke dealer 3. Brushes badly worn 3. Check and replace if necessary 4. Fuse blown 4. Check and replace if necessary If condition persists, consult your dealer 5. Motor faulty 5. Consult your Clarke dealer. Motor runs but disc 1. Flange nut not tight 1. Tighten flange nut does not turn 2. Gear shaft or key broken 2.
Spare Parts Diagram (Figure 3) Spare Parts List No. Part No. Description 1 Motor Brush KP12201 2 Handle KP12202 3 Wheel/Disk Guard KP12203 4 Inner Flange KP12204 5 Outer Flange K{12205 6 Grinding Wheel / Cutting Disc ( See Clarke Accessories below ) 7 Flange Tool KP12207 8 Casing KP12208 Recommended Grinding Wheels / Cutting Discs Clarke Accessories Description Part No.
VIBRATION EMISSIONS HAND-ARM VIBRATION Employers are advised to refer to the HSE publication “Guide for Employers”. All hand held power tools vibrate to some extent, and this vibration is transmitted to the operator via the handle, or hand used to steady the tool. Vibration from about 2 to 1500 herz is potentially damaging and is most hazardous in the range from about 5 to 20 herz.
The graph below shows the vibration value against the maximum time the respective tool may be used, per day. It should be noted that if a tool is used under abnormal, or unusual conditions, then the vibration level could possibly increase significantly. Users must always take this into account and make their own risk assessment, using the graph above as a reference.
DECLARATION OF CONFORMITY - 15 -
NOTES
