Operation Manual

ManualsBrandsClarion ManualsAudioClarion XC6610

Owner’s manual & Installation manual

Mode d’emploi et manuel d’installation

Manual de instrucciones y de instalación

XC AMPLIFIER

AMPLIFICATEUR XC

AMPLIFICADOR XC

XC6610

Summary of content (13 pages)

PAGE 1
Owner’s manual & Installation manual Mode d’emploi et manuel d’installation Manual de instrucciones y de instalación XC6610 XC AMPLIFIER AMPLIFICATEUR XC AMPLIFICADOR XC
PAGE 2
INTRODUCTION The Clarion XC6610 is a full-featured, six-channel amplifier incorporating the English following features: • Conformably Coated PC Board that resists mold, mildew and moisture damage. • Pulse-Width Modulated (PWM) MOSFET power supply for maximum performance with minimal distortion. • Remote turn-on with “soft start” muting to prevent turn-on “thump”. • Variable high-pass/low-pass electronic crossover with a 12dB per octave slope (adjustable range: 50Hz to 500Hz).
PAGE 3
DESCRIPTION English The XC6610 uses a PWM regulated power supply for superior sound and output wattage. All of the connections and controls for the XC6610 are conveniently labeled and located on one side of the amplifier. To ensure the best possible electrical connections, the power, speaker and RCA inputs are corrosion resistant. An additional benefit of the XC6610 is the ability to create a 3, 4, 5 or 6 configuration.
PAGE 4
English The RCA connections are corrosion resistant for optimum performance and low signal loss. The RCA connectors are labeled CH1, CH2, CH3, CH4, CH5, CH6. In applications where RCA signals are not present, the speaker level output from the head unit can be used. (High-level speaker output to RCA input adapters included). • Input Gain Controls: Allow you to match the source unit’s output voltage to achieve maximum output from the amplifier.
PAGE 5
Set Auto Sense to ON INPUT SELECT 4 CH. 6 CH. 2 CH.
PAGE 6
INSTALLATION This section suggests Mounting and Wiring Precautions for installing the Clarion XC6610. If you do not posses the necessary tools and installation experience, do not attempt to install these amplifiers. Instead, contact your local Clarion Audio dealer to perform the installation. English MOUNTING PRECAUTIONS Owner’s Manual Prior to mounting the amplifier, make sure it is safe to mount the amplifier in desired location. Failure to do so can result in serious damage to the vehicle/ boat.
PAGE 7
English 7. When creating passage holes for power cables, RCA’s cables, and speaker wires, use grommets to eliminate any sharp edges created during drilling. This will protect the wire from being damaged and prevent a short circuit. 8. Extra cable can cause signal loss and act as an “antenna” for noise. Use only high-quality RCA cables that are no longer than necessary. 9. In multiple amplifier systems, it is recommended to use a relay on the remote turn-on lead of the radio.
PAGE 8
6-Channel Stereo System 4-Channel High-Pass, 2-Channel Low-Pass INPUT SELECT 4 CH. 6 CH. 2 CH.
PAGE 9
5-Channel Stereo System, 4-Channel High-Pass, Bridged Low-Pass 2 CH INPUT AUTO SENSE OFF ON CH5-6 BASS BOOST CH3 CH1 CH5 FREQ Hz 110 50 0 dB 12 HIGH LOW FULL 500 REM GAIN MIN 330 GND 4 CH INPUT 500 CH2 330 HIGH LOW FULL FREQ Hz 110 50 GAIN MIN 240 MAX CH3 500 CH4 330 MAX CH5 CH6 CH6 CH4 CH2 + 12V HIGH LOW FULL FREQ Hz 110 50 240 CH1 2 X 40 AMP MAX GAIN MIN MAX English INPUT SELECT 4 CH. 6 CH. 2 CH.
PAGE 10
SETTING THE GAIN English After completing the installation, follow these steps to set the Input Gain Control. 1. Set Input Gain Control to MIN (counterclockwise). 2. Power on source. Set all Tone or Equalization Controls to “flat” positions and set Loudness off. 3. Play a CD, set the Source Volume Control to 75% of max level. 4. Slowly adjust the Input Gain Control of amplifier. Stop when you hear a slight distortion of audio.
PAGE 11
TROUBLESHOOTING Problem No Audio. Amplifier not powering on. (LED turned off) Solution English Remote turn-on voltage. Check remote connections at amplifier and source unit. Blown amplifier fuse. Replace with new fuse (same rating). Power wires not connected. Check power and ground wiring at amplifier and at battery. Speaker leads shorted. Check speaker continuity to ground, it should not show a common ground. Speakers not connected or are blown.
PAGE 12
PRODUCT SPECIFICATIONS English Owner’s Manual Frequency Response Crossover Frequency (Low, High, Full) Low Level Input Sensitivity Max. Power Output RMS Power Output RMS Power Output RMS Bridged Power Output Fuse Dimensions (W x H x D) 20Hz ~ 20kHz Variable 50Hz ~ 500Hz 200mV ~ 6.0V 1000W @4Ω 85W x 6 @1.0% THD @2Ω 125W x 6 @1.0% THD @250W x 3 @1.0% THD 40A x 2 288mm x 55mm x 174mm 11-3/8in x 2-3/16in x 6-7/8in Power Output: 85W x 6RMS [4Ω @ ≤14.