Users Manual Model No.
List of content 1. General information - Name of product - Model Name - Descriptions 2. Procedure to build in 2.1 Procedure for HJZ0095 2.2 Procedure for HJZ0093 3. Pin Description of Connector 4. Label Information 4.1 HJZ0095 4.2 HJZ0093 5. Caution 6. Regulatory information 7.
1. General information - Name of product Bluetooth Module - Model Name Manufacture name Xanavi Informatics Corporation Difference of product Sony Corporation - HJZ0093 (*1) HJZ0095 (*2) Output PCM clock signals included Synch clock as CXN1041-3AAC master mode from the module - 921.6kbps in UART Baud rate - Input PCM clock signals included Synch clock as slave CXN1041-3ABC mode to the module - 115.
2. Procedure to build in: 2.
Two screws FPC cables with connectors Two screws FPC cables with connectors 3) Removing four screws and pulling out FPC cable from the connectors Three screws Three screws 4) Removing six screws 5
2.
2.
A screw 2) Removing four screws and pulling out FPC cable from the connectors CF bracket CF Bluetooth cover Bluetooth module FPC-35pin FPC-15pin CF & HDD pwb CF ejector Bottom is contact side Clinches CF shield cover A screw 8
3.
4. Label Information 4.
4.
5. Caution - The following sentence has to be displayed on the outside of the device in which the module is installed: "Contains Transmitter Module FCC ID: SJ2HJZ0095", or "Contains FCC ID: SJ2HJZ0095". - Please note that this users manual should not be provided to end-users. - In the User manual or Label of the device (end-set), which install HJZ0095 or HJZ0093, following Regulatory information should be mentioned. 6.
7. Product information 7.1. 頁 製品仕様 ..................................................................................................................................14 7.1. 製品概要 ...............................................................................................................................14 7.2. 電気的特性 ...........................................................................................................................16 7.3. FIRMWARE .............................................
7.1. 製品仕様 7.1. 製品概要 CXN1041 は Bluetooth Specification Ver.1.2 Class2 の認証を取得した、Bluetooth 用 RF/ベースバン ドフルモジュール 7.1.1. 特長 ・UART,PCM CODEC,PIO のインターフェースに対応 ・パッケージサイズ:12× 25× 2.55 [mm] ・内蔵 FLASH MEMORY 容量は 8M Bit ・アンテナ搭載 ・CXD3264GL は、CSR 社の BlueCore4-EXT と完全コンパチブル ・1 つのマスタから7 スレーブまで対応 ・チャネル品質駆動データレート 一般仕様 ・品名 Bluetooth モジュール ・型番 CXN1041-3AAC、CXN1041-3ABC ・外部 IF UART(BCSP BAUD RATE 921.6kbaud)、PCM、PIO ・電源電圧 2.7〜3.6 [V] ・外形寸法 12× 25× 2.55 [mm] 7.1.2.
7.1.3.
7.2. 電気的特性 7.2.1. 絶対最大定格 項目 保存温度範囲 最小値 最大値 単位 - 40 85 ℃ - 0.40 3.60 V 項目 最小値 最大値 単位 動作温度範囲 - 40 85 ℃ 2.70 3.60 V 電源電圧 VDD 7.2.2. 推奨動作条件 電源電圧 VDD 7.2.3. 入力/出力端子特性 (Ta:-40〜+85℃) ※ 本端子特性は、CXN1041 の内部で使用している CXD3264GL の仕様です。 デジタル端子 最小値 標準値 最大値 単位 - 0.4 +0.8 V 0.7VDD VDD+0.4 V 0.2 V 入力電圧 V IL 入力ロジックレベルLow 2.7≦VDD≦3.6V V IH入力ロジックレベルHigh 出力電圧 V OL 出力ロジックレベルLow 2.7≦VDD≦3.6V (IO=4.0mA) VOL出力ロジックレベルHigh 2.7≦VDD≦3.6V (IO=- 4.0mA) VDD- 0.
7.2.4.
7.2.5. 消費電流 モード 平均値 単位 SCO接続HV3(30ms interval Sniff Mode) 21 mA SCO接続HV1(マスタまたはスレーブ) 42 mA ACLデータ転送720kbps UART(マスタまたはスレーブ) 45 mA ACL接続、スニフモード40ms間隔、38.4kbps UART 3.2 mA ACL接続、スニフモード1.28s間隔、38.4kbps UART 0.45 mA Parkedスレーブ、1.28ビーコン間隔、38.4kbps UART 0.55 mA スタンバイモード(ホスト接続、RF停止) 47.0 μ A Reset 15.0 μ A 最大消費電流:100mA 以下 7.3. Firmware Software Stack CSR HCI Stack (Ver.19.
添付資料 1: 使用部品 使用している主要部品 品名 メーカー 備考 CXD3264GL ソニーセミコンダクター九州(株) Bluetooth IC MBM29SL800BE90PW- J - ERE1 Spansion J apan 株式会社 Flash Memory LDA31 村田製作所 株式会社 チップアンテナ MM8430- 2600B 村田製作所 株式会社 SW付RFコネクタ AXK6F20345Y 松下電工株式会社 20ピン、ボードトゥボードコネクタ 適合コネクタ:AXK5F20545Y 19