User's Manual

ManualsBrandsCLAMCASE ManualsElectronicsiPad Accessory with KB and BT radio

WELCOME

Charging the CLAMCASE

™

Keyboard Battery

1. Insert the smaller end of the USB Charging Cable

into the port on the right side of the CLAMCASE

™

Keyboard.

2. Insert the larger end of the USB Charging Cable into

your computer or an iPad

charger which is plugged

into an electrical outlet. The Charge Indicator LED

glows orange while charging.

3. Fully charge the battery (approximately 90 minutes)

before initial use. The Charge Indicator LED turns

green when the CLAMCASE

™

Keyboard is fully

charged.

Note: To check battery life at any time while using the

CLAMCASE

™

Keyboard, hold down fn + ctrl. The Power

Pair LED ashes to indicate current battery life:

# of Flashes Battery Life

4 75-100%

3 50-75%

2 25-50%

1 0-25%

Cleaning Your CLAMCASE

™

Follow these general rules when cleaning your

CLAMCASE

™

. Be sure to remove your iPad

prior to

cleaning.

• Use a damp, soft, lint-free cloth to clean the exterior

and interior, avoiding the CLAMCASE

™

Keyboard and

any openings. Do not allow moisture in any openings.

• Do not allow any liquids to come into contact with the

CLAMCASE

™

Keyboard or openings.

• Do not use aerosols, solvents, or abrasives while

cleaning.

Position Your CLAMCASE

™

Keyboard Position

• Open the case so that the

CLAMCASE

™

Keyboard is resting on

a table or your lap and utilize the full

QWERTY keyboard.

Touchscreen Position

• Flip the CLAMCASE

™

Keyboard

upside down and position the screen

in landscape view to achieve the

perfect angle for any activity.

Desktop Position

• Set the CLAMCASE

™

upright in

portrait position for hands free

viewing of photos and additional

content.

Tablet Position

• Flip the CLAMCASE

™

Keyboard all

the way around to enjoy your iPad

tablet.

Note: To avoid inadvertent key hits, turn off the clamcase

keyboard by holding down the power key for two seconds.

When ready to use the keyboard again hold down the power

key for two seconds to activate it.

Troubleshooting

If your CLAMCASE

™

isn’t functioning properly upon

receipt, go to clamcase.com, click Support, click Contact

Support, and submit your issue to Customer Service. Be

sure to have your order number and a good description

of the issue when submitting.

If you are having issues working the CLAMCASE

™

Keyboard or connecting to your iPad

, try the following

solutions:

Ensure the batteries of both the iPad

and the

CLAMCASE

™

Keyboard are charged.

Ensure that Bluetooth

is set up correctly on the

iPad

. Review your iPad

documentation for more

information.

Disconnect other Bluetooth

devices from the iPad

and attempt to reconnect the CLAMCASE

™

Keyboard.

Reset the iPad

by holding down the Home button and

the Lock button for two seconds.

Insert a pin or a paper clip into the hole next to the USB

Charging Port to reset the CLAMCASE

™

Keyboard, and

try to reconnect the CLAMCASE

™

Keyboard.

If none of the above fixes the issue, contact

CLAMCASE

™

support at clamcase.com/support.

Environmental Requirements

Follow these guidelines for the use of your CLAMCASE

™

to ensure optimum performance. Only operate in

temperatures between 32°F and 95°F (0°C to 35°C).

Do not operate your CLAMCASE

™

in high-humidity

levels (above 95% non-condensing) Maximum

non-pressurized operating altitude: 10,000 ft (3000 m).

FCC Compliance Statement

The equipment has been tested and found to comply with limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by tuning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measure:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly

approved by the party responsible for compliance could void the user’s

authority to operate this equipment. (Example – use only shielded interface

cables when connecting computer or peripheral devices).

USA: - This device complies with Part 15 of the FCC Rules. Operation is

subject to the following conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Canada: - Operation is subject to the following two conditions: (1) this device

may not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

To satisfy RF exposure requirements, this device and its antenna must operate

with a separation distance of at least 20 centimeters form all persons and

must not be co-located or operating in conjunction with any other antenna

or transmitter.

Disposal and Recycling Information

When this product reaches its end of life, please dispose of it according to your

local environmental laws and guidelines.

Battery Disposal Information

Dispose of batteries according to your local environmental laws and guidelines.

Summary of content (2 pages)

PAGE 1
welcome Position Your CLAMCASE™ Keyboard Position Charging the CLAMCASE™ Keyboard Battery 1. Insert the smaller end of the USB Charging Cable into the port on the right side of the CLAMCASE ™ Keyboard. 2. Insert the larger end of the USB Charging Cable into your computer or an iPad ® charger which is plugged into an electrical outlet. The Charge Indicator LED glows orange while charging. 3. Fully charge the battery (approximately 90 minutes) before initial use.
PAGE 2
Package Contents • CLAMCASE ™ Quick Start Guide Setting Up Your CLAMCASE™ • USB Charging Cable • Quick Start Guide 1 1. For optimal experience, CLAMCASE™ performs best with iOS 4.2 or later. Simply plug your iPad® device into your computer via USB and select update to iOS 4.2 or later software through iTunes® for the free updates. 2 Attaching Your iPad® to the CLAMCASE™ 1. Slide the left side of the iPad® into the bottom edge of the recessed area. 2.