CIDRON QR Installation guide Cidron Standard QR Reader Cidron Combi QR Reader
Cidron Standard (VG3 QR) Reader - Technical specifications Operating frequency 13,56MHz. Reading technologies MIFARE® CSN 4 byte, MIFARE® CSN 7 byte, MIFARE® Classic, MIFARE® Plus and MIFARE DESFire® EV1. Also supports other ISO 14443 A/B* compatible cards. *Not all ISO14443 B cards have been implemented in the reader, please contact Civintec Global for more details on current status.
Cidron Combi (VG3 QR) Reader - Technical specifications Operating frequency Reading technologies Mobile ID Barcode/QR scanner 125KHz & 13,56MHz. Electromarine EM4200, MIFARE® CSN 4 byte, MIFARE® CSN 7 byte, MIFARE® Classic, MIFARE® Plus and MIFARE® DESFire EV1. Also supports other ISO 14443 A/B* compatible cards. *Not all ISO14443 B cards have been implemented in the reader, please contact Civintec Global for more details on current status.
Power Consumption Model Feature Model: Civintec Global Cidron SC93100-MDEB STD 13.56MHz/125KHz/2.4GHz with keypad SC93110-MDEB STD 13.56MHz/125KHz/2.4GHz without keypad SC93200-MDB SLIM 13.56MHz/2.4GHz with keypad SC93210-MDB SLIM 13.56MHz/2.
2x 2x 2x 1x 1x Package content: • 1pc Installation plate • 1pc Reader module with front plate • 1pc Front cover • 2pcs Terminal connector (8-pin) • 2pcs Installation screws • 2pcs Screw plugs • 1pc Cable strip • 1pc Fixing screw • 1pc Quick installation guide * Please note that all pictures in this manual are illustrations and do not represent the actual sizes and form of the components.
4x 4x 4x 1x 1x Package content: • 4pcs Installation screws • 4pcs Screw plugs • 4pcs Fixing screw • 1pc Tamper switch bolt 1 • 1pc Tamper switch bolt 2 * Please note that all pictures in this manual are illustrations and do not represent the actual sizes and form of the components.
~20 cm In order to facilitate installation a cable length of 20cm is recommended.
Ensure that the installation plate is fixed in the correct direction, i.e. the arrows pointing upwards.
Ensure that the area behind the tamper switch bulb of the installation plate is flat, to be able to push the bulb for correct tamper alarm functionality. If it is not flat enough, you will find accessories in this manual that will assist with improving this functionality.
P5 - Black socket P4 - Blue socket Make sure to place the terminal connectors with the fastening screws facing towards you.
P4 Blue T/GPIO3 GPIO1 GPIO2 GND B/RX A/TX GND DC+ P5 Black D+/RX D1 D0 D-/TX G-LED R-LED BZ K-LED Tamper output General purpose I/O General purpose I/O Ground RS485 RS485 + Power supply Power supply 9-30 VDC x x x x x x x x x x x x x x x x QR-RX Wiegand D1/CLK Wiegand D0/DATA QR-TX Green LED control Red LED control Buzzer control External Keypad LED control x x x x x x x x - P4 - Blue RS485/ OSDP Description T/GPIO3 GPIO1 GPIO2 GND B/RX A/TX GND DC+ P5 - Black Wiegand PIN D+/RX D1 D0 D-/T
QRcode mode There are four wires,power and communication 1.Red wires(DC+),The first PIN that connects to the terminal block 2.Black wires(GND),The second PIN connects to the terminal block 3.Green wires(RX),The 9 PIN connects to the terminal block 4.
Make sure no excess connection cable is left in between the reader module and the installation plate. Use the enclosed cable strip to fix the cable in the cord grip. It is recommended to connect the the wires to the terminal connectors before tightening the cable strip.
Install Mounting Plate with QR CODE MODE * Screws and screw plugs included with accessory. Matte black, part no: SC9192-SQ QRcode mode There are four wires,power and communication 1.Red wires(DC+),The first PIN that connects to the terminal block 2.Black wires(GND),The second PIN connects to the terminal block 3.Green wires(RX),The 9 PIN connects to the terminal block 4.
Cleaning instructions Use compressed air in between the buttons to remove dust and dirt and after that Isopropyl alcohol can be used with a piece of fabric to rub in between the buttons and the reader exterior.
When installing the reader to the mounting plate ensure that the reader pin header contact perfectly aligns with the terminal connector block.
Mount the front cover as per the image above and make sure it is fitted correctly. In order to do so, allign and fit the top snap fastening, apply and maintain pressure on the top of the front cover while sliding the front cover over the bottom snap fastening.
To secure the front cover to the reader use the supplied fixing screw and fix it into the installation plate through the front cover.
Cidron installation tool, part no: SC9914 To open the reader, first remove the fixing screw and then detach the front cover from the installation plate by inserting the tip of the tool into the slot at the bottom of the front cover and move the tool upwards. This will release the front cover without damaging the front cover and/or the installation plate.
Overview, programming of reader Setting the reader in programming mode see page: 19 Configuring the reader Changing authentication card Resetting the OSDP secure channel.
Setting the reader in programming mode BEEP ! Reading distance approximately 2 cm. In order to set the reader in programming mode, present the valid “Authentication Card” to the reader as shown. The reader will beep and start blinking yellow to indicate that it is now in programming mode. The Reader is in programming mode for 10 seconds. If no other programming card is presented within this time, the reader will return to normal mode.
Configuring the reader BEEP ! Reading distance approximately 2 cm. 1: Set the reader in programming mode, see page: 19 2: Present the “Configuration Card” to the reader as shown. Keep the card within reading distance until the reader beeps and blinks in green. The reader is now programmed and ready for use according to the configuration settings on the configuration card.
Changing authentication card BEEP ! Reading distance approximately 2 cm. 1: Set the reader in programming mode, see page: 19 2: Present the “CHANGE Authentication Card” to the reader as shown. Keep the card within reading distance until the reader beeps and blinks in green. The reader is now reprogrammed to only be set in programming mode by the new “Authentication Card”. The old “Authentication Card” is no longer authorized to set the reader in programming mode.
Resetting the OSDP secure channel. BEEP ! Reading distance approximately 2 cm. 1: Set the reader in programming mode, see page: 19 2: Present the “OSDP Installation mode Card” to the reader as shown. Keep the card within reading distance until the reader beeps and blinks in green. The reader has now reset the secure channel encryption keys to installation mode.
Installing Secure Access Module MIFARE® SAM AV2 (SIM Card) In order to install the SAM into the reader open the SAM socket by unlocking and opening the lid. Then place the SAM into the socket lock it into place by closing the lid and sliding it into locked position.
FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The Cidron reader family are intended for Sale to professional security companies and installation by experienced security professionals. Civintec Global can not provide assurance that any entity or person buying or obtaining the product is properly experienced or trained to correctly install security related products including card readers. CiVinTec Global Co., Limited. info@civintec.com www.civintec.com Version 2.