Ref.No:171.
Safety Instructions 1. Read Instructions-All the safety and operating instructions should be read before this product is operated. 2. Retain Instruction- The safety and operating instruction should be retained for future reference. 3. Heed Warnings- All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instruction should be followed. 5.
20. Accessories -Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall,causing serious injury to a child or adult, and serious damage to the Product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer instructions, and should use a mounting accessory recommended by the manufacturer. 21.
Main Features 3 band EQ w/ input gain control per channel. High level master output, headphone output. Power on/off switch. Master output level meter. Mic on/off/talkover function. Low sound leakage crossfader. USB computer connection (record & playback). Controls and Features Top panel 17 5 16 4 6 1 15 7 2 12 8 3 13 9 14 10 11 Features & Functions Top Panel 1. Microphone Volume This knob is used to regulate the microphone output volume.
Microphone Bass Control This knob is used to adjust the bass levels of the Microphone with a maximum signal gain of 10dB or maximum signal decrease of -10dB. Turning the knob in a counter-clockwise direct -ion will decrease the amount of bass applied to the microphone signal, turning the knob in a clockwise direction will increase the amount of bass applied to microphone signal. 4. Talkover Switch When engaged this function will decrease all signal levels, except the microphone level, by 14dB. 5.
headphones on. Be sure the CUE MIXINGKNOB (13) is turned to the “CUE” position to hear the selected channel source. 15. Master Volume Control This rotary knob is used to control the master output level (volume). To avoid distorted output try to maintain an average output signal level below “OVER”. Be sure this volume control is always set to zero before turning the unit on. 16. LED Monitor Display The dual LED’s indicators are used to indicate the master output level. 17.
NOTE:(1)USB cable limit within 3 meter. (2)To use the USB2.0 connection, please also refer to the operation manual of your computer and the programmers used. 25 26 25. DJ Microphone Jack This jack is used to a connect a microphone to the mixer. Connect you microphone via1/4 inch (6.3mm) jack. The signal volume will be controlled by the DJ MIC KNOB (1) . The bass and treble levels can also be adjusted by the built-in MICROPHONE EQ (2/3). 26.
Specifications POWER SOURCE: DIMENSION: WEIGHT: AC 9V 1000mA 254 (W) x 308 (D) x 82.5 (H)mm 3.4 Kgs INPUT/OUTPUT IMPEDANCE & SENSITIVITY: (MASTER +4.5dBV OUTPUT, LOAD = 100K OHM ,MAXIMUM GAIN, EQ FLAT) LINE: 10-50K OHM /-10dBV (320mV) ±2dB PHONO: 47K OHM /-50dBV (3.16mV) ±2dB MIC: 2.2K OHM /-50dBV (3.16mV) ±2dB MASTER: 1K OHM +4.5dBV (1.68V) ±2dB PHONES (Load=32 ohm) 33ohm/1dBV ( 1.
THD+N: LESS THAN 0.02% (0dBfs, 1KHz; W/ 20KHz LPF, MAXIMUM GAIN) FREQUENCY RESPONSE: 20 - 20KHz +/- 2dB (MAXIMUM GAIN) S/N RATIO: MORE THAN 85dB (W/ 20KHz LPF, A-WEIGHTED, MAXIMUM GAIN) CH SEPARATION: MORE THAN 70dB AT 1KHz (0dBfs, W/ 20KHz LPF, A-WEIGHTED,MAXIMUM GAIN) RECORDING AND PLAYBACK: (LINE 1KHz,-14dBV INPUT, GAIN MAXIMUM, 600 ohm impedance) OUTPUT: 2.5dBV +/-2dB THD+N LESS THAN 0.
For other Citronic products in the range, visit . . . www.citronic.