Cisco IPTV Receivers Product Manual ISB7105 For use with your AT&T U-verse TV service
Contents Notice for Installers .......................................................................................................... 4 IMPORTANT SAFETY INSTRUCTIONS.............................................................................. 4 Change the Way You Watch TV ....................................................................................... 7 What’s In the Carton? ...................................................................................................... 7 Safety First ....
Notice for Installers The servicing instructions in this notice are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualified to do so. Note to System Installer For this apparatus, the cable shield/screen shall be grounded as close as practical to the point of entry of the cable into the building.
IMPORTANT SAFETY INSTRUCTIONS, continued Ground the Product WARNING: Avoid electric shock and fire hazard! If this product connects to cable wiring, be sure the cable system is grounded (earthed). Grounding provides some protection against voltage surges and built-up static charges. Protect from Exposure to Moisture and Foreign Objects WARNING: Avoid electric shock and fire hazard! Do not expose this product to dripping or splashing liquids, rain, or moisture.
Change the Way You Watch TV Welcome to Internet Protocol TV (IPTV). The ISB7105 device, known as an IPTV receiver, brings a rich, new set of interactive services directly to you through your TV and your in-home IP network. The receiver uses wireless technology 802.11n to connect to the network. The ISB7105 receiver allows for easy and secure connection to IPTV services.
Front Panel AT&T U-verse POWER LINK HD MENU REC OK 1 2 3 4 5 6 7 8 9 10 11 1 Power Turns the receiver on or places it in standby. To restart the receiver, press and hold the POWER button for 10 seconds. The LED is green 2 Model Number Identifies the model number of your receiver as ISB7105 3 Signal Strength Indicator Identifies the strength of the wireless connection 4 Link Indicates network link status.
Back Panel ® NETWORK 1 Pr Pb 2 Y R VIDEO OUT AUDIO OUT HDMI OPTICAL POWER 3 4 5 6 7 1 Network Connect to the Ethernet (CAT-5) network at your home, if applicable 2 YPbPr Connect the receiver to the component video input (YPbPr) on the HDTV.
Connecting the Receiver To connect your receiver to your network and home entertainment devices, complete these steps. 1 Because the connections 16 4 for a high-definition (HD) or standard-definition (SD) 9 3 or TV are different, you must determine if your TV is HD or SD. Your TV must receive HD signals for you to enjoy the benefits of HDTV. Refer to the manual that came with your TV for more information. See page 25 for more information on picture formats.
The ISB7105 receiver allows for easy and secure connection to IPTV services. The signal strength indicator on the front panel of the receiver identifies the strength of the wireless connection and aids in the proper placement of the receiver. AT&T U-verse POWER LINK HD REC ISB7105 Signal Strength Indicator T15770 ISB7105 Wireless Network Connection • The receiver must be paired with the wireless access point for the wireless connection to be established. See page 12 for more information.
Connecting the Wireless Access Point to the Gateway RJ-45 Cable 1. Connect the 12 VDC Power Supply plug on the access point to the wall power outlet. Use only the power adapter provided with the product. 3. Connect the supplied yellow Ethernet cable to the yellow port on the back of the wireless access point. Ethernet 12VDC 4. Connect the other end of the RJ-45 Ethernet cable to an available yellow Ethernet port on your gateway.
Connections for a High-Definition TV (HDTV) To use the receiver with an HDTV, you must make one of the following connections to view the HD content. Refer to the owner’s manual for your TV and the cabling diagrams in this manual for more detailed connection information. Although all connections provide you with quality service, we list the connections in our recommended order. Notes: • The labeling on your receiver or HDTV may vary slightly from the illustrations shown below.
Connections for a Standard-Definition TV (SDTV) When using the receiver with an SDTV, you must make one of the following connections to view content. Some SDTVs may not have all these connections. Refer to the owner’s manual for your TV and the cabling diagrams in this manual for more detailed information. Although all connections provide you with quality service, we list the connections in our recommended order.
Connections for a VCR or DVD Recorder When using the receiver with a VCR or DVD recorder, you must make one of the following connections to view content. Although all connections provide you with quality service, we list the connections in our recommended order. Notes: • The labeling on your receiver, VCR, or DVD recorder may vary slightly from the illustrations shown below. • Some cables shown in the connection diagrams may not be included with this receiver.
Connecting to an HDTV with an HDMI Connector Cable Used in this Configuration • 1 HDMI Cable Notes: • The HDMI port on the TV must support high-bandwidth digital content protection (HDCP). • The HDMI interface supports Dolby Digital 5.1 audio. WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.
Connecting to an HDTV with a DVI Connector Cables Used in this Configuration • 1 HDMI-to-DVI Cable or 1 HDMI Cable and 1 HDMI-to-DVI Adapter • 1 Audio Left/Right Cable (You can also use an optical cable [indicated by the dotted line] instead of the Audio Left/Right Cable as shown in the diagram, dependent upon your TV’s capabilities.) Notes: • The DVI port on the TV must support high-bandwidth digital content protection (HDCP).
Connecting to an HDTV with Component (YPbPr) Connectors Cables Used in this Configuration • 1 Component Video Cable (YPbPr) • 1 Audio Left/Right Cable (You can also use an optical cable [indicated by the dotted line] instead of the Audio Left/Right Cable as shown in the diagram, dependent upon your TV’s capabilities.) WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.
Connecting to an SDTV with Component (YPbPr) Connectors Cables Used in this Configuration • 1 Component Video Cable (YPbPr) • 1 Audio Left/Right Cable Note: The receiver must be set to the proper standard-definition mode. WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.
Connecting to an SDTV with an RCA-Type Connector Cables Used in this Configuration • 1 RCA-type Video Cable • 1 Audio Left/Right Cable WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.
Connecting to a Home Theater System with Component (YPbPr) Connectors Cables Used in this Configuration • 1 Component Video Cable (YPbPr) • 1 Audio Left/Right Cable (You can also use an optical cable [indicated by the dotted line] instead of the Audio Left/Right Cable as shown in the diagram.) Notes: • This connection requires that audio is provided by the home theater system. • Consult the user guide that came with your home theater system for information on connecting your other video and audio devices.
Connecting to a Stereo VCR or DVD Recorder (optional) The diagram below shows how to connect a recording device to your receiver. Although it is possible to watch TV using a connection through your VCR or DVD recorder to the TV, this connection may not provide the best picture, and HDTV users are restricted to an SD format. In addition, some content is copy protected and passing this content through the recording device may result in a picture that cannot be viewed.
Troubleshooting If the receiver does not perform as expected, the following tips may help. If you need further assistance, contact your service provider. No Picture • • • • Verify that the power to your TV is turned on. Verify that your wireless receiver and wireless access point are powered on. Verify that all cables are properly connected. If your system includes a VCR, DVD recorder, or stereo, verify that you have properly connected the device to the receiver.
Frequently Asked Questions What Is Digital Television? Digital television (DTV) is a huge leap forward in television technology compared to analog television that has been widely available since the 1940s. DTV is delivered and displayed using digital encoding, similar to the way a PC operates. By using digital technology, there is no variation in picture and sound quality from the origination point until it is displayed on your television.
Picture Formats What Is the Difference Between a Standard-Screen and a Wide-Screen HDTV? The type of screen your HDTV has (wide-screen or standard-screen) determines how the receiver displays programs on the screen. The picture format for an HDTV is a combination of aspect ratio and screen resolution and is different for standard-screen and wide-screen HDTVs. What Is Aspect Ratio? An aspect ratio is the ratio of the width to the height of the TV screen.
Index A D AC Power input Arrow keys 8 Aspect ratio 24 Audio Out 9 DC Power output 9 Diagrams. See Connecting the receiver to other devices Digital Video Recorder. See DVR 9, 13, 14, 15 Digital TV, What is it B DVD Connection Back panel 9 DVI connector Burn-in of screen Buttons 24 9, 10, 15, 22 13, 17 23 E See Front Panel Ethernet 9, 12 C F Cables 9, 12-23 CAT-5 See Ethernet Coaxial Cable Input FAQs 23 Compliance, FCC 28 Component video connection.
Index, continued K T Keys. See Front panel To TV (Video Out) connector Troubleshooting N Network TV 9, 10, 11 digital, what is it O formats Optical Audio Output 9, 13, 17, 18, 21 Over-the-air converter box 25 15 programming resolution 25 25 wide-screen Progressive screen resolution 25 13, 23 8 V VCR connection S Scan rates. See screen resolution View programs Screen W resolution size 9, 15, 22 Video Out.
Compliance Information United States FCC Compliance This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against such interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IMPORTANT NOTE: Canada RF Exposure Statement: This system has been evaluated for radio frequency exposure for humans in reference to Canada Health Code 6 (2009) limits. The evaluation was based on evaluation per RSS-102 Rev 4. The minimum separation distance from the antenna to general bystander is 7.9 inches (20cm) to maintain compliance. Note: The ISB7105 has disabled the 5600-5650M band by S/W to avoid 5600-5650M band for IC certification.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Manufactured under license from Dolby Laboratories.
