Installation Guide Cisco CIS330 High-Definition IPTV Set-Top POWER LINK HD RECORD MENU OK
Notice for Installers The servicing instructions in this notice are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualified to do so. Note to System Installer For this apparatus, the coaxial cable shield/screen shall be grounded as close as practical to the point of entry of the cable into the building.
Contents IMPORTANT SAFETY INSTRUCTIONS ...................................................................... 4 Change the Way You Watch TV ................................................................................... 6 Safety First ................................................................................................................... 6 Serial Number............................................................................................................... 6 In This Manual .............
IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. Power Source Warning 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. A label on this product indicates the correct power source for this product.
IMPORTANT SAFETY INSTRUCTIONS, continued Provide Ventilation and Select a Location • Remove all packaging material before applying power to the product. • Do not place this apparatus on a bed, sofa, rug, or similar surface. • Do not place this apparatus on an unstable surface. • Do not install this apparatus in an enclosure, such as a bookcase or rack, unless the installation provides proper ventilation.
Change the Way You Watch TV Welcome to Internet Protocol Television (IPTV). The Cisco® CIS330 High-Definition IPTV Set-Top with DVR brings a new set of services directly to you through your TV and your in-home IP network. The set-top uses existing in-home network wiring and connects to most all entertainment devices.
Front Panel Features POWER 1 LINK 2 HD 3 RECORD 4 OK MENU 5 6 7 8 9 T13209 1 Power Turns the set-top on or places it in standby mode. The LED is green 2 Link Indicates network link status. The LED is green 3 HD Indicates that a high-definition program is in progress. The LED is blue 4 Record Indicates that a recording is in progress. The LED is red 5 IR Sensor Receives the infrared signal from the remote control.
Back Panel Connectors Note: Image may vary from actual product. L Pb NETWORK USB 1 2 Pr 3 4 R Y S-VIDEO 5 VIDEO OUT 6 AUDIO OUT OPTICAL 7 8 TO TV TO WALL (VIDEO OUT) (VIDEO IN) POWER 9 10 11 1 Network Connect to the Ethernet (CAT-5) network in your home, if applicable 2 USB Port USB connector 3 HDMI Connect an HDTV HDMI™ (High-Definition Multimedia Interface) cable from the HDTV to the HDMI port.
Connecting Your Set-Top To connect your set-top to your network and home entertainment devices, complete these steps. 1 Because the connections 16 4 for a high-definition (HD) or 3 9 or standard-definition (SD) TV are different, you must determine if your TV is HD or SD. Your TV must receive HD signals for you to enjoy the benefits of HDTV. Refer to the manual that came with your TV for more information. See page 23 for more information on picture formats.
Connecting to the Home Network The following diagrams illustrate examples of the connections you can use to connect your set-top to your in-home network. Contact your service provider for the recommended connection method for your home. Note: The in-home coaxial and phoneline wiring networks use HomePNA™ 3.
Connections for an HDTV To use the set-top with an HDTV, you must make one of the following connections to view the HD content. Refer to your TV user guide and the cabling diagrams in this guide for more detailed connection information. Notes: • The labeling on your set-top or HDTV may vary slightly. • Some cables shown in the connection diagrams may not be included with this set-top. AUDIO OUT See the connection diagram on page 15 for an example.
Connections for an SDTV When using the set-top with an SDTV, you must make one of the following connections to view content. Some SDTVs may not have all these connections. Refer to your TV user guides and the cabling diagrams in this guide for more detailed information. Notes: • The labeling on your set-top or SDTV may vary slightly. • Some cables shown in the connection diagrams may not be included with this set-top.
Connections for a VCR or DVD Recorder When using the receiver with a VCR or DVD recorder, you must make one of the following connections to view content. Notes: • The labeling on your set-top, VCR, or DVD Recorder may vary slightly. • Some cables shown in the connection diagrams may not be included with this set-top. AUDIO OUT Video Out L For VCRs or DVD Recorders with Video and Left and Right audio connectors, you can use the Video Out and the Audio Out connectors (Left and Right) on the set-top.
Connecting to an HDTV with an HDMI Connector Cable Used in this Configuration • 1 HDMI-to-HDMI Cable Note: The HDMI port on the TV must support high-bandwidth digital content protection (HDCP). WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the set-top.
Connecting to an HDTV with a DVI Connector Cables Used in this Configuration • 1 HDMI-to-DVI Cable or 1 HDMI-to-HDMI Cable and 1 HDMI-to-DVI Adapter • 1 Set Audio Left/Right Cables Tips: • The DVI port on the TV must support high-bandwidth digital content protection (HDCP). • When you connect the HDMI connector to the DVI connector on your HDTV, you need an HDMI-to-DVI adapter, and you need a separate audio connection.
Connecting to an HDTV with Component (YPbPr) Connectors Cables Used in this Configuration • 1 Set Component Video Cables (YPbPr) • 1 Set Audio Left/Right Cables WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the set-top.
Connecting to a Home Theater System with Component (YPbPr) Connectors Cables Used in this Configuration • 3 Sets Component Video Cables (YPbPr) • 2 Sets Audio Left/Right Cables (you can also use optical cables instead of the Audio Left/Right Cables as shown in the diagram, indicated by dotted lines) • 1 RCA-type Video Cable Note: This connection assumes that audio is provided by the home theater speakers.
Connecting to a Stereo VCR or DVD Recorder (optional) This connection, in addition to some other connections to the TV, allows you to record and play back programming on your VCR. Cables Used in this Configuration • 1 RCA-type Video Cable • 1 Set Audio Left/Right Cables Note: This connection does not provide an HD signal to the TV. You must use one of the video connections shown on pages 14-16 or page 19 in addition to this connection to obtain an HD signal to the TV.
Connecting to an SDTV with Component (YPbPr) Connectors Cables Used in this Configuration • 1 Component Video Cable (YPbPr) • 1 Set Audio Left/Right Cables Note: The set-top must be set to the proper output mode, typically 480i or 480p. WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the set-top.
Connecting to an SDTV with an RCA-Type Connector Cables Used in this Configuration • 1 RCA-type Video Cable • 1 Set Audio Left/Right Cables WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the set-top.
Connecting to an SDTV with a Coaxial Cable Cable Used in this Configuration • 1 Coaxial cable with standard F connectors Note: You must set the channel on your TV to the correct channel (either channel 3 or channel 4). Contact your service provider for the channel information. WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the set-top.
Troubleshooting If the set-top does not perform as expected, the following tips may help. If you need further assistance, contact your service provider. No Picture • Verify that the power to your TV is turned on and the Link light is lit. • If the set-top is plugged into a wall switch, verify that the switch is in the ON position. • Verify that all cables are properly connected. • If your system includes a VCR or stereo, verify that you have properly connected them to the set-top.
Frequently Asked Questions What Is Digital Television? Digital television (DTV) is a huge leap forward in television technology compared to analog television that has been widely available since the 1940s. DTV is delivered and displayed using digital encoding, similar to the way a PC operates. By using digital technology, there is no variation in picture and sound quality from the origination point until it is displayed on your television.
Picture Formats What Is the Difference Between a Standard-Screen and a Wide-Screen HDTV? The type of screen your HDTV has (wide-screen or standard-screen) determines how the set-top displays programs on the screen. The picture format for an HDTV is a combination of aspect ratio and screen resolution and is different for standard-screen and wide-screen HDTVs. What Is Aspect Ratio? An aspect ratio is the ratio of the width to the height of the TV screen.
Index D A AC Power input Arrow keys Diagrams. See Connecting the set-top to other devices 8 7 Aspect ratio Audio Out Digital TV, What is it 23, 24 DVI connector 8, 11, 12 23 11, 15 E B Back panel Ethernet network 8 Burn-in of screen 22 F Buttons. See Front panel FAQs C Cables CAT-5 8, 9, 10 9, 10, 13-21 23 FCC compliance 27 Formats, picture 24 Frequently Asked Questions.
Index, continued P T Picture formats 23-24 To Wall (Video In) connector Ports. See Connectors To TV (Video Out) connector Power Troubleshooting 7, 8 Programs, view 22, 23, 24 Progressive scan rate 8, 12, 20 22 TV 24 digital, what is it formats R 23 9, 24 HDTV, what is it RGB connector 8, 10 11 23 programming resolution S 23 23-24 screen size.
Compliance Information United States FCC Compliance This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against such interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
Scientific Atlanta, A Cisco Company 5030 Sugarloaf Parkway, Box 465447 Lawrenceville, GA 30042 678.277.1000 www.scientificatlanta.com Product and service availability is subject to change without notice. © 2007-2008 Cisco Systems, Inc. All rights reserved.
