Cisco Content Services Switch Getting Started Guide Software Version 4.01 December, 2000 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
Access Registrar, AccessPath, Are You Ready, ATM Director, Browse with Me, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, CiscoLink, the Cisco NetWorks logo, Cisco Powered Network logo, Cisco Systems Networking Academy, Fast Step, FireRunner, Follow Me Browsing, FormShare, GigaStack, IGX, Intelligence in the Optical Core, Internet Quotient, IP/VC, iQ Breakthrough, iQ Expertise, iQ FastTrack, iQ Logo, iQ Readiness Scorecard, Kernel Proxy, MGX, Natural Network Viewer, Network Registrar, the Networkers logo
C O N T E N T S About This Guide xv Audience xv How to Use This Guide xvi Related Documentation xvii Documentation Map xix Symbols and Conventions xx CHAPTER 1 Unpacking and Installing the CSS 1-1 Site Requirements 1-2 Required Tools and Equipment 1-2 Shipment Contents 1-2 Unpacking the CSS 1-4 Unpacking the CSS 11050 or CSS 11150 1-4 Unpacking the CSS 11800 1-4 If the Product is Damaged 1-6 Installing the CSS 11050 or CSS 11150 1-6 Installing the CSS 11050 or CSS 11150 as a Free-Standing Unit 1-7 Rack-
Contents Installing the CSS 11800 1-9 Mid-Mounting the CSS 11800 Brackets 1-10 Extend-Mounting the CSS 11800 Brackets 1-11 Rack-Mounting the CSS 11800 Chassis 1-14 Installing a CSS 11800 Module 1-15 Installation Precautions and Restrictions 1-15 Installation Precautions 1-15 Module Slot Restrictions 1-16 Hot Swapping a Module 1-18 Unpacking a CSS 11800 Module 1-18 Installing a Module 1-19 Installing a Passive SCM or SFM 1-21 Passive Module Switchover 1-22 CHAPTER 2 Cabling the CSS 2-1 Cabling the CSS 11
Contents Gigabit Ethernet Module Connectors and LEDs 2-20 Gigabit Ethernet Module LEDs 2-22 Switch Fabric Module (SFM and SFM2) Connectors and LEDs 2-22 SFM and SFM2 LEDs 2-26 Internal Disk Module LEDs 2-26 Internal Disk Module LEDs 2-28 Connecting Power Cords 2-28 Connecting a CSS 11050 or CSS 11150 Power Cord 2-28 Connecting a CSS 11050 or CSS 11150 AC Power Cord 2-29 Connecting a CSS 11150 DC Power Cord 2-29 Connecting a CSS 11800 Power Cord 2-31 Connecting a CSS 11800 AC Power Cord 2-31 Connecting a CS
Contents Booting the CSS on a Routine Basis 3-9 Performing Hardware Initialization and Power-On Diagnostics 3-9 Checking Results of Previous Shutdown 3-10 Logging into the CSS 3-11 CHAPTER Configuring the CSS 4-1 4 Service, Owner, and Content Rule Overview 4-1 Using the Configuration Script 4-3 Configuring Layer3 Load Balancing 4-6 Configuring Layer 5 Load Balancing 4-8 Configuring Proxy Cache 4-11 Configuring Transparent Cache 4-14 Where to Go Next 4-17 APPENDIX A Specifications A-1 Electrical Spec
Contents Supported Protocols A-7 Transport A-7 Network A-7 Routing A-8 Gateway A-8 Application A-8 Network Utilities A-8 Network Management A-9 DC Power Supply Safety Warnings A-10 Lithium Battery Disposal Warnings A-11 APPENDIX B Cable Pinouts B-1 RJ-45 Fast Ethernet Connector Pinouts B-1 RJ-45 RS-232 Serial Connector Pinouts B-2 RJ-45 Timing BITS Connector Pinouts B-5 RJ-45 Management Connector Pinouts B-5 APPENDIX C Troubleshooting 3-1 Troubleshooting the Console Interface 3-1 Troubleshooting the
Contents APPENDIX D Regulatory Information D-1 Regulatory Standards Compliance D-1 Canadian IC CS-03 Requirements D-2 Avis D’Industrie Canada D-3 FCC and Telephone Company Procedures and Requirements D-4 Radio Frequency Interference D-4 If Problems Arise D-5 Example Affidavit (United States) D-6 INDEX Content Services Switch Getting Started Guide x 78-11766-01
F I G U R E S Figure 1-1 CSS 11800 Shipping Pallet Figure 1-2 Front-Mounting the Brackets on the CSS 11050 or CSS 11150 1-8 Figure 1-3 Mid-Mounting the Brackets on the CSS 11050 and CSS 11150 1-8 Figure 1-4 Aligning Brackets on the CSS 11800 for Mid-Mounting Figure 1-5 Screw Holes on the CSS 11800 Bracket for Front and Extended Mounting Figure 1-6 Aligning Brackets on the CSS 11800 Chassis for Extended Mounting Figure 1-7 Fully Configured CSS 11800 Figure 1-8 Installing a Module into a CSS
Figures Figure 2-15 Switch Fabric Module 2 Connectors and LEDs Figure 2-16 Internal Disk Module LEDs Figure 2-17 Connecting a CSS 11050 or CSS 11150 AC Power Cord Figure 2-18 Location of CSS 11150 DC Power Supply Connectors Figure 2-19 Connecting a CSS 11800 AC Power Cord Figure 2-20 Location of CSS 11800 DC Power Supply Connectors 2-25 2-27 2-29 2-30 2-32 2-34 Content Services Switch Getting Started Guide xii 78-11766-01
T A B L E S Table 1-1 Chassis Slot Usage Table 2-1 CSS 11050 and CSS 11150 Ethernet Management Port LED Descriptions Table 2-2 CSS 11050 Front Panel LED Descriptions 2-4 Table 2-3 CSS 11150 Front Panel LED Descriptions 2-8 Table 2-4 Switch Control Module LED Descriptions 2-16 Table 2-5 CSS Console Port Default Settings Table 2-6 Fast Ethernet Module LED Descriptions Table 2-7 Gigabit Ethernet Module LED Descriptions Table 2-8 Switch Fabric Module LED Descriptions Table 2-9 CSS 11800 I
Tables Table B-3 RJ-45 Connector to a DB-9 or DB-25 Connector Console Cable Pinouts Table B-4 RJ-45 RS-232 Serial Connector Pinouts for the Diag Port Table B-5 RJ-45 RS-232 Serial Connector Pinouts for the SFM2 Diag1 and Diag2 Port Table B-6 RJ-45 Timing BITS Connector Pinouts Table B-7 RJ-45 Management Connector Pinouts B-5 Table C-1 Troubleshooting the Console Interface 3-2 Table C-2 Troubleshooting the CSS 11050 or CSS 11150 CSS Power Supply Table C-3 Troubleshooting the CSS 11800 Power
About This Guide This guide is intended to help you quickly get your CSS 11050, CSS 11150, and CSS 11800 content services switches (hereinafter referred to as the CSS) installed and into operation. It provides you with instructions for installing, cabling, booting, and configuring the CSS. Information in this guide applies to all CSSs except where noted.
About This Guide How to Use This Guide How to Use This Guide This section describes the chapters and contents in this guide. Chapter Description Chapter 1, Unpacking and Installing the CSS This chapter provides instructions for unpacking and installing the CSS. Chapter 2, Cabling the CSS This chapter provides instructions for cabling the CSS and the CSS 11800 modules, and describes the CSS LEDs and connectors.
About This Guide Related Documentation Related Documentation In addition to this document, the Content Services Switch documentation set includes the following: Document Title Description Content Services Switch Release Note The release note provides information not in the previous guides and reference.
About This Guide Related Documentation Document Title Description Content Services Switch Advanced Configuration Guide This guide describes how to configure advanced CSS features, including Content Services Switch Command Reference • Sticky parameters • HTTP header load balancing • Source groups, ArrowPoint Control Lists (ACLS), Extension Qualifier Lists (EQLs), Uniform Resource Locator Qualifier Lists (URQLs), Network Qualifier Lists (NQLs), and Domain Qualifier Lists (DQLs) • VIP and CSS redu
About This Guide Related Documentation Documentation Map This section provides a map for using the CSS documentation set.
About This Guide Symbols and Conventions Symbols and Conventions This guide uses the following symbols and conventions to emphasize certain information. Caution A caution means that a specific action you take could cause a loss of data or adversely impact use of the equipment. Warning A warning describes an action that could cause you physical harm or damage the equipment. Note A note provides important related information, reminders, and recommendations. Bold text indicates a command in a paragraph.
C H A P T E R 1 Unpacking and Installing the CSS This chapter describes how to unpack and install the CSS 11050, CSS 11150, and CSS 11800 content services switches (hereinafter referred to as the CSS) as free-standing or rack-mount units.
Chapter 1 Unpacking and Installing the CSS Site Requirements Site Requirements Before you select an installation site for the CSS, read the electrical, environmental, and physical requirements as described in Appendix A, Specifications. If you are installing a DC unit (CSS 11150 or CSS 11800 only), ensure that you read and follow the DC power supply safety warnings in Appendix A, Specifications.
Chapter 1 Unpacking and Installing the CSS Shipment Contents • Note Software License Key (located on a card in an envelope in the Accessory kit) If you cannot find the software license key, call the Cisco Technical Assistance Center (TAC) toll free, 24 hours a day, 7 days a week at 1-800-553-2447 or 1-408-526-7209. You can also email TAC at tac@cisco.com.
Chapter 1 Unpacking and Installing the CSS Unpacking the CSS Unpacking the CSS The CSS is shipped in a protective shipping carton. The CSS 11050 and CSS 11150 are shipped as a self-contained chassis; no modules or components can be added or removed. The CSS 11800 is shipped with the power supply, fan unit, SCM, and SFM preinstalled. You must install all separately ordered items (for example, I/O modules or a redundant AC or DC power supply) into the CSS 11800.
Chapter 1 Unpacking and Installing the CSS Unpacking the CSS 3. Check the configuration of the CSS and the accessories against the packing slip. Report any discrepancies as described in “If the Product is Damaged” in this chapter. 4. Using a Phillips screwdriver, remove the screws from the shipping brackets on the pallet. Figure 1-1 shows the CSS 11800 attached to the wooden pallet. 5. Carefully remove the CSS from the pallet.
Chapter 1 Unpacking and Installing the CSS If the Product is Damaged If the Product is Damaged If any portion of the unit or component is damaged in transit, forward an immediate request to the delivering carrier to perform an inspection of the product and to prepare a damage report. Save the container and all packing materials until the contents are verified. Concurrently, report the nature and extent of the damage to Customer Service.
Chapter 1 Unpacking and Installing the CSS Installing the CSS 11050 or CSS 11150 Caution Note Do not remove the CSS 11050 or CSS 11150 cover. There are electrical shock hazards present in the unit if the cover is removed. There are no serviceable or installable components available with the CSS 11050 and CSS 11150 CSS. Removing the CSS 11050 or CSS 11150 cover voids its warranty.
Chapter 1 Unpacking and Installing the CSS Installing the CSS 11050 or CSS 11150 To install the mounting brackets on the CSS chassis: 1. Position the CSS with its front panel facing you. On the left and right side of its chassis, note the screw holes for installing the mounting brackets. 2. Position a bracket on one side of the chassis. Align the bracket with the appropriate screw holes for front- or mid-mounting. Figure 1-2 illustrates front-mounting the brackets.
Chapter 1 Unpacking and Installing the CSS Installing the CSS 11800 Installing the CSS into the Rack Before you begin, you will need a #2 Phillips screwdriver and four pan-head screws. To install the CSS 11050 or CSS 11150 into an equipment rack: 1. Raise the CSS to the installation height. Align the screw holes on the mounting bracket with the holes on the equipment rack. 2. Use a #2 Phillips screwdriver and two pan-head screws to secure each mounting bracket to each side of the rack.
Chapter 1 Unpacking and Installing the CSS Installing the CSS 11800 Mid-Mounting the CSS 11800 Brackets To change the location of the mounting brackets on the CSS 11800 chassis from a front-mount position to a mid-mount position (refer to Figure 1-4): Figure 1-4 1. Remove the seven front mounting bracket screws from one side of the chassis. 2.
Chapter 1 Unpacking and Installing the CSS Installing the CSS 11800 4. Repeat steps 1 through 3 to install the second bracket onto the other side of the chassis. When the brackets are in position for mounting the chassis in a rack, proceed to the “Rack-Mounting the CSS 11800 Chassis”. Extend-Mounting the CSS 11800 Brackets You can extend-mount a CSS 11800 chassis to set the front edge of the unit behind the front edge of the rack to allow the chassis to be installed in an enclosed rack.
Chapter 1 Unpacking and Installing the CSS Installing the CSS 11800 Figure 1-5 Screw Holes on the CSS 11800 Bracket for Front and Extended Mounting Front Screw holes for the extended-mounting of the 11800 chassis in a cabinet 49570 Screw holes for the front-mounting of the 11800 chassis in a cabinet Front Left bracket Left bracket To change the location of the mounting brackets on the CSS 11800 chassis from a front-mount position to an extended-mount position: 1.
Chapter 1 Unpacking and Installing the CSS Installing the CSS 11800 Figure 1-6 Aligning Brackets on the CSS 11800 Chassis for Extended Mounting Mounting bracket Mounting bracket Mounting key 49571 Mounting key 3. Using a Phillips screwdriver, install the seven #10-32 pan-head screws through the extended-mount bracket holes into the CSS. 4. Repeat steps 1 through 3 to install the second bracket onto the other side of the chassis.
Chapter 1 Unpacking and Installing the CSS Installing the CSS 11800 Rack-Mounting the CSS 11800 Chassis Once the mounting brackets are installed, you are ready to install the CSS 11800 chassis. Warning The weight and position of the CSS 11800 chassis within the cabinet may make the cabinet top-heavy or unstable. Take all necessary precautions to anchor the cabinet securely before installing the chassis. To install the CSS 11800 chassis into a cabinet: 1.
Chapter 1 Unpacking and Installing the CSS Installing a CSS 11800 Module Installing a CSS 11800 Module This section applies to the CSS 11800 modules only and contains the following sections: • Installation Precautions and Restrictions • Unpacking a CSS 11800 Module • Installing a Module • Installing a Passive SCM or SFM Installation Precautions and Restrictions This section includes background material related to installing a module into the CSS 11800 chassis.
Chapter 1 Unpacking and Installing the CSS Installing a CSS 11800 Module Module Slot Restrictions Modules are restricted to specific slots due to bandwidth capabilities. The CSS 11800 chassis backplane is designed for specific modules to reside in their respective slots. For example, you cannot install a SCM in slot 2 because the backplane connector for slot 2 does not accommodate a SCM connector. Prior to installing a module, refer to Table 1-1 for information on chassis slot usage.
Chapter 1 Unpacking and Installing the CSS Installing a CSS 11800 Module Figure 1-7 Fully Configured CSS 11800 Slot 15 49572 Slot 1 Content Services Switch Getting Started Guide 78-11766-01 1-17
Chapter 1 Unpacking and Installing the CSS Installing a CSS 11800 Module Hot Swapping a Module Warning Do not hot swap an active SCM, SFM, or SFM2 from a CSS. Hot swapping these active modules terminates all communications within the CSS and causes the CSS to reboot. If you replace an active SCM with a new SCM, the boot configuration reverts back to its default settings. You must reconfigure these parameters through the Offline Diagnostic Monitor menu.
Chapter 1 Unpacking and Installing the CSS Installing a CSS 11800 Module 4. Remove the module from the anti-static shielding bag and inspect it for damage. Always hold the module by the faceplate, being careful not to touch the components. If the module appears to be damaged, return it to the anti-static bag, repack it in the shipping carton, and contact your local supplier. 5. For the procedure on installing a module into the CSS 11800 chassis, refer to “Installing a Module”.
Chapter 1 Unpacking and Installing the CSS Installing a CSS 11800 Module Installing a Module into a CSS 11800 Chassis 49573 Figure 1-8 4. Close both ejectors simultaneously to seat the module connector into the backplane. 5. Using a Phillips screwdriver, tighten the spring-loaded screws on the front of the module faceplate. Once you install the module, it begins diagnostics and initializes automatically. If you installed a SFM or SFM2, you must reboot the chassis to activate it. 6.
Chapter 1 Unpacking and Installing the CSS Installing a CSS 11800 Module Installing a Passive SCM or SFM You can install a passive SCM or SFMs (which includes SFM2s) in a CSS 11800 chassis. Passive modules are stand-by modules in case of an active module failure. When an active module fails, the passive module becomes active. Passive modules do not load share processing functions with the active module. Note The SCM contains a small lithium battery.
Chapter 1 Unpacking and Installing the CSS Installing a CSS 11800 Module 4. Insert the module into the board guides at the top and bottom of the slot and slide it into the chassis by pressing firmly at the top and bottom of the faceplate. 5. Close both ejectors simultaneously to seat the module connector into the backplane. 6. Using a Phillips screwdriver, tighten the spring-loaded screws on the front of the module faceplate. 7. • A SCM module begins diagnostics and initializes automatically.
C H A P T E R 2 Cabling the CSS This chapter describes the individual CSS interfaces, how to cable the CSS and its interfaces, how to attach a console for console management, and how to connect the AC or DC power cord. This chapter also describes the CSS LEDs and connectors. The information in this chapter applies to the CSS 11050, CSS 11150, and CSS 11800 except where noted.
Chapter 2 Cabling the CSS Cabling the CSS 11050 and CSS 11150 CSS 11151 Content Services Switch 49574 Figure 2-1 The CSS 11050 configuration supports: • 8 auto-sensing 10/100-Mbps Ethernet (10BASE-T/100BASE-TX) interfaces • Optional integrated Gigabit Ethernet Network Interface Card (GENIC) with one uplink port The CSS 11150 configuration supports: • 12 auto-sensing 10/100-Mbps Ethernet (10BASE-T/100BASE-TX) interfaces • Optional integrated Gigabit Ethernet Network Interface Card (GENIC) with t
Chapter 2 Cabling the CSS Cabling the CSS 11050 and CSS 11150 CSS 11050 and CSS 11150 Rear Panel Connectors and LEDs Power switch AC connector Ethernet management port Management 1 Link/Act Duplex 10/100 0 49575 Figure 2-2 10/100 Ethernet Table 2-1 describes the LEDs on the rear panel.
Chapter 2 Cabling the CSS Cabling the CSS 11050 and CSS 11150 Figure 2-3 CSS 11051 Front Panel Connectors and LEDs 100BASE-TX 4X 6X 8X 1 2 3 4 5 6 7 8 Diag RS-232 1X 3X 5X Power Status Ready 49576 Console 10 D Li /1 up nk 00 lex /A ct 2X 7X The CSS 11052, as shown in Figure 2-4, also has one Gigabit Ethernet connection using a Gigabit Interface Converter (GBIC), and associated Transmit, Receive, and Link LEDs. The GBIC complies with Revision 5.
Chapter 2 Cabling the CSS Cabling the CSS 11050 and CSS 11150 Table 2-2 CSS 11050 Front Panel LED Descriptions (continued) LED Name Color State Indicates 10/100 (Fast Ethernet ports) Green Off Port is operating at 10 Mbps On Port is operating at 100 Mbps Power Green Off CSS does not have power On CSS has power Off CSS is operational Blinking CSS detects an error during offline or online testing, or the boot diagnostic failed and the system cannot boot Off CSS is booting On CSS is
Chapter 2 Cabling the CSS Cabling the CSS 11050 and CSS 11150 CSS 11150 Front Panel Connectors and LEDs All front panels of the CSS 11150 models front panels contain connectors and LEDs that vary according to their model number.
Chapter 2 Cabling the CSS Cabling the CSS 11050 and CSS 11150 Figure 2-7 CSS 11153 Front Panel Connectors and LEDs .
Chapter 2 Cabling the CSS Cabling the CSS 11050 and CSS 11150 Note The CSS 11155 has a similar appearance to the CSS 11154, but its memory size per port is 8 MB instead of 4 MB. Table 2-3 describes the LEDs on the CSS 11150.
Chapter 2 Cabling the CSS Cabling the CSS 11050 and CSS 11150 Table 2-3 CSS 11150 Front Panel LED Descriptions (continued) LED Name Color State Indicates Rx (Receive) (Gigabit ports on the CSS 11154 or CSS 11155) Green Off No receive packet activity Blinking Receive activity detected Link/Sync (Gigabit ports on the CSS 11154 or CSS 11155) Green Off No link On Link exists and synchronization achieved Blinking Link exists but not synchronized Off No link established On Link establishe
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Cabling the CSS 11800 Modules The CSS 11800 modules has connectors and LEDs on their front rear panels.
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules • Eight slots configurable with either: – Fast Ethernet modules providing eight auto-sensing 10/100-Mbps Ethernet (10BASE-T/100BASE-TX ) RJ-45 ports or six 10BASE-T/100BASE-TX ports and two 100BASE-FX ports – Gigabit Ethernet modules providing up to four 1000-Mbps Ethernet (1000BASE-SX) Gigabit Interface Converter (GBIC) interfaces with either 8 megabytes of flow connection memory supporting up to 64,000 simultaneous flows or 16 megabytes of flow
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules CSS 11800 Content Services Switch 49582 Figure 2-9 Switch Control Module Connectors and LEDs The Switch Control Module (SCM) provides master control and packet memory storage and is responsible for the following functions: • System powerup and boot control • Centralized routing table management • System-wide connection management • Interface to external Network Management Station • Disk management (internal disk module) Content Services
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules • Provides two external RS-232 interfaces • Building Integrated Timing Service support While only one SCM is required in a configuration, you can install and configure a passive SCM for redundancy. A maximum of two SCMs are allowed in a chassis. Note The SCM contains a small lithium battery. Some jurisdictions restrict the ways in which items containing lithium batteries may be disposed.
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Switch Control Module Connectors The Switch Control Module (model CSS8-SCM) contains the following connectors and LEDs: • 1 RJ-45 10/100-Mbps Fast Ethernet management connector • 1 RJ-45 RS-232 Console connector • 1 RJ-45 RS-232 Diag connector (reserved for field service diagnostic use only) • 1 RJ-45 Building Integrated Timing Supply (BITS) Clock RS-422 connector • Power, Status, and Active module LEDs • Duplex, 10/100, and Active LEDs f
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Figure 2-10 Switch Control Module Connectors and LEDs .
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Switch Control Module LEDs The SCM front panel LEDs indicate module and configuration status. Table 2-4 describes the SCM LEDs and their indications.
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Configuring a Terminal to the SCM Console Port This section describes how to configure a terminal connected to the SCM console port. Initially, the terminal settings must match the CSS default settings as specified in Table 2-5.
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Figure 2-11 8-Port Fast Ethernet Module Connectors and LEDs Power LED Module ejector Status LED 10/100 LEDs Ready LED Duplex LEDs Link LEDs RJ-45 10BASE-T/100BASE-TX connectors 49584 Module ejector Content Services Switch Getting Started Guide 2-18 78-11766-01
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Figure 2-12 illustrates the LEDs and connectors on the FEM model CSS8-IOM-6/2/FE.
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Fast Ethernet Module LEDs The FEM front panel LEDs indicate module and network status. Table 2-6 describes the FEM LEDs .
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Figure 2-13 Gigabit Ethernet Module Connectors and LEDs Power LED Module ejector Status LED Receive LEDs Ready LED Link/sync LEDs Transmit LEDs Gigabit interface converter (GBIC) SC fiber connectors (top - receive, bottom - transmit) 1 2 Ports 2 through 4 for additional GBIC connectors 3 4 49586 Module ejector Content Services Switch Getting Started Guide 78-11766-01 2-21
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Gigabit Ethernet Module LEDs The GEM front panel LEDs indicate module status (Power, Status, and Ready LEDs) and network status for each of the connectors (Transmit, Receive, and Link LEDs). Table 2-7 describes the GEM LEDs .
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Each module provides 10-Gbps switch control element for switching functionality and flow processing for four I/O modules. You can install a second active module to service four additional I/O modules. Both active modules are on simultaneously in the CSS 11800. The chassis enables you to configure two additional passive modules for redundancy.
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Figure 2-14 illustrates the SFM front panel LEDs and connectors. Figure 2-14 Switch Fabric Module Connectors and LEDs Power LED Module ejector Status LED Active LED Debug console and diag console 49587 Module ejector The SFM2 contains two RJ-45 RS-232 Diag1 and Diag 2 connectors, combining both Console and Diag functions on each connector (all of these connectors are reserved for field service diagnostic use only).
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Note These connectors are for serial data only and are not compatible with Ethernet RJ-45 cable connectors. Figure 2-15 illustrates the SFM2 (model CSS8-SFM2) front panel LEDs and connectors Figure 2-15 Switch Fabric Module 2 Connectors and LEDs .
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules SFM and SFM2 LEDs The SFM and SFM2 front panel LEDs indicate operating and configuration status. Table 2-8 describes the SFM LEDs and their indications .
Chapter 2 Cabling the CSS Cabling the CSS 11800 Modules Figure 2-16 Internal Disk Module LEDs Power LED Module ejector Status LED Active LED 49589 Module ejector Content Services Switch Getting Started Guide 78-11766-01 2-27
Chapter 2 Cabling the CSS Connecting Power Cords Internal Disk Module LEDs The CSS 11800 IDM front panel LEDs indicate operating and activity status. Table 2-9 describes the IDM LEDs and their indications .
Chapter 2 Cabling the CSS Connecting Power Cords Connecting a CSS 11050 or CSS 11150 AC Power Cord To connect an AC power cord to a CSS 11050 or CSS 11150: 1. Ensure that the CSS power switch is in the 0 (off) position. 2. Attach the power cord to the CSS by plugging the AC power cord connector into the power receptacle at the rear panel, as shown in Figure 2-17 Figure 2-17 Connecting a CSS 11050 or CSS 11150 AC Power Cord AC -100 -240 VAC 50 - 60HZ 3.1A Max. 300W Max. Power switch 49590 .
Chapter 2 Cabling the CSS Connecting Power Cords Warning Before performing the DC installation procedure, ensure that power is removed from the DC circuit. To ensure that all power is off, locate the circuit breaker that services the DC circuit and switch it off. To connect the CSS 11150 DC power supply to a power source: 1. Locate the DC terminal block on the front of the chassis as shown in Figure 2-18. Figure 2-18 Location of CSS 11150 DC Power Supply Connectors . Terminal block DC -48 input 7.
Chapter 2 Cabling the CSS Connecting Power Cords 3. Install the wires into the appropriate connector. Make sure that the uninsulated part of each wire is 9mm (0.35 in.) in length. When installing the wires, always connect the ground wire first. When disconnecting the wires, always disconnect the ground wire last. The proper power cable wiring between the CSS 11150 and DC power source is illustrated in Table 2-10.
Chapter 2 Cabling the CSS Connecting Power Cords Figure 2-19 Connecting a CSS 11800 AC Power Cord . PS1 power switch PS1 PS2 PS2 AC power cord 49592 PS2 power switch PS1 AC power cord 3. Plug the power cord into a dedicated 3-wire grounding receptacle. 4. Switch on the power on the CSS.
Chapter 2 Cabling the CSS Connecting Power Cords Connecting a CSS 11800 DC Power Cord Before you install a DC power cord, refer to Appendix A, Specifications for DC power supply safety warnings. Warning The DC power supply cord requires 12 AWG wire. The CSS 11800 draws a maximum of 25 amps. Warning DC systems do not have a power switch. A chassis configured for DC power requires an external power disconnect device (such as an external circuit breaker).
Chapter 2 Cabling the CSS Connecting Power Cords Figure 2-20 Location of CSS 11800 DC Power Supply Connectors . .35" (9mm) + – PS1 DC Terminal block 49593 PS1 DC Terminal block 2. Warning Using a flat-head screwdriver, loosen the captive screws on the three DC connectors (labeled from left to right,+, –, and , respectively). Before installing a wire, ensure that the polarity of the DC connections is correct.
Chapter 2 Cabling the CSS Connecting Power Cords The proper power cable wiring between the CSS 11800 and DC power source is illustrated in Table 2-11. Table 2-11 CSS 11800 to DC Power Source Cabling CSS 11800 DC Power Source (Ground) (Ground) + + – – 4. Tighten the captive screws to 5 to 7 inch-pounds (.6 to .8 Nm) of torque to secure the wires in the connectors . Ensure the wires are held firmly in place.
Chapter 2 Cabling the CSS Connecting Power Cords Content Services Switch Getting Started Guide 2-36 78-11766-01
C H A P T E R 3 Booting the CSS This chapter describes the CSS disk directory structure, powering the CSS, and the CSS boot sequence.
Chapter 3 Booting the CSS CSS Software Overview You can also install the CSS software on a network drive on an NT system which the CSS can access through FTP. The Content Services Switch and System Software compact disk contains the CSS software for the network drive. This software is in Zip format and must be copied and uncompressed on a network drive. For more information on configuring a network boot drive, refer to the Content Services Switch Basic Configuration Guide.
Chapter 3 Booting the CSS CSS Software Overview The software directory also contains the startup-config file. This file is an ASCII file containing commands the CSS executes at startup. This file is created when you: • Complete using the configuration script. • Issue the copy running-config startup-config or write memory command. These commands also save configuration changes to the startup-config during a CSS session. • Use File Transfer Protocol (FTP) to copy a startup-config file to the CSS.
Chapter 3 Booting the CSS Connecting the Console Connecting the Console To connect a console to the CSS and power up the CSS, attach the console cable (provided in the Accessory kit) to the Console port on the CSS 11050 or CSS 11150 front panel, or to the CSS 11800 SCM panel. Your terminal settings must match the following CSS default settings: • Baud Rate: 9600 • Data Bits: 8 • Flow Control: none • Parity: none • Stop Bits: 1 1.
Chapter 3 Booting the CSS Booting the CSS for the First Time For example: (config-boot)# shutdown Once the CSS shuts down all processes, you may remove power from the CSS. Booting the CSS for the First Time When the CSS initially boots up, it: • Performs hardware diagnostics. • Validates the integrity of the disk file system automatically.
Chapter 3 Booting the CSS Booting the CSS for the First Time Note Your license key is located on a card in an envelope in the Accessory kit. If you cannot find the software license key, call the Cisco Technical Assistance Center (TAC) toll free, 24 hours a day, 7 days a week at 1-800-553-2447 or 1-408-526-7209. You can also email TAC at tac@cisco.com. The CSS prompts you to accept the license agreement. You must accept the license agreement or you cannot log into the CSS.
Chapter 3 Booting the CSS Booting the CSS for the First Time Configuring the Ethernet Management Port Once you enter a valid license key at the boot prompt, the CSS displays the following message and prompt: Use the Ethernet management port IP address to access the Content Services Switch for configuration and management only. This port does not route traffic and is not associated with VLAN circuits.
Chapter 3 Booting the CSS Booting the CSS for the First Time Enter: • yes to change the username and password. The CSS prompts you for this information and password confirmation. Enter username: Enter password: Confirm password: • no to keep the default username and password.
Chapter 3 Booting the CSS Booting the CSS on a Routine Basis The CSS then enables you to access the Offline DM menu. Press any key to access the Offline Diagnostic Monitor menu... To access the Offline DM menu, press any key within 5 seconds. Refer to the next sections for information on using the Offline DM menu. If you do not wish to access the Offline DM menu after seeing this message, do not press a key.
Chapter 3 Booting the CSS Booting the CSS on a Routine Basis Table 3-1 defines the boot states and the Status and Ready LED blinking patterns. Table 3-1 Module Status and Ready LED Boot Definitions State Sequence Status LED Ready LED 1. Off line and not active Off Off 2. Offline testing Off Blinking Blinking Off Offline tests detect an error 3. Off line and active (Offline Diagnostic Monitor is On displayed) On 4. On line and not active On Off 5.
Chapter 3 Booting the CSS Booting the CSS on a Routine Basis During a check disk, the CSS detects and recovers from the following error conditions: • File Allocation Tables (FATs) are out of synchronization • Sector write truncation revitalization (may occur from a power loss at the time the CSS is writing to the disk) • Bad cluster identification and mapping in the FAT when reformatting the disk • Crosslinked FAT entries • Disk entry validation, name, size, cluster assignment, cluster chaining
Chapter 3 Booting the CSS Booting the CSS on a Routine Basis The CSS prompts you to enter a username and password. Enter the default user name admin and the default password system as lowercase text, or enter the administrative username and password you configured during the boot process or using the Offline DM menu. For security, the CSS does not display the password. User Access Verification Username: Password If you connect a console to the CSS after the CSS boots, your screen will be blank.
C H A P T E R 4 Configuring the CSS This chapter provides information on service, owner, and content rules, and how to configure the CSS through configuration scripts.
Chapter 4 Configuring the CSS Service, Owner, and Content Rule Overview • Note A content rule is a hierarchical rule set containing individual rules that describe which content (for example, .html files) is accessible by visitors to the web site, how the content is mirrored, on which server the content resides, and how the CSS should process requests for the content. Each rule set must have an owner.
Chapter 4 Configuring the CSS Using the Configuration Script Content rules are hierarchical. That is, if a request for content matches more than one rule, the characteristics of the most specific rule apply to the flow. The hierarchy for content rules is shown below. The CSS uses this order of precedence to process requests for the content, with 1 being the highest match and 8 being the lowest match. 1. Domain name, IP address, protocol, port, URL 2. IP address, protocol, port, URL 3.
Chapter 4 Configuring the CSS Using the Configuration Script The configuration script allows you to create services, owners, and content rules based on your entries and then enables you to: • Configure Layer 3 load balancing • Configure Layer 5 load balancing • Configure Proxy cache • Configure Transparent cache • Exit from the script and save the information you entered to the running-config To accept the script default values, press the Enter key at the prompts.
Chapter 4 Configuring the CSS Using the Configuration Script ############################################## #Setup Script for the Content Services Switch# ############################################## Checking for Existing Config... No startup-config was found, continue with the setup script [y/n]? y Note: Pressing “q” after any prompt quits setup. Pressing after any [y/n] defaults to “y”. Warning: All circuit VLAN IP addresses must be on a different subnet than the Ethernet Mgt port IP address.
Chapter 4 Configuring the CSS Using the Configuration Script Configuring Layer3 Load Balancing A layer 3 load balancing configuration enables the CSS to use a Virtual IP address (VIP) to load balance Web traffic to Web servers based on IP addresses.
Chapter 4 Configuring the CSS Using the Configuration Script To accept the script default values, press the Enter key at the prompts. Creating Layer3 load balancing Enter service name: [default = Server1] Enter service IP address: [default = 192.168.10.3] 192.168.3.58 Create another service? [y/n]? y Enter service name: [default = Server2] Enter service IP address: [default = 192.168.10.3] 192.168.3.59 Create another service? [y/n]? n Enter Virtual IP address for L3_Rule: [default = 192.168.10.4] 192.168.
Chapter 4 Configuring the CSS Using the Configuration Script !**************** OWNER ****************** owner L3_Owner content L3_Rule add service Server1 add service Server2 vip address 192.168.3.6 balance aca active ########################################## ## Setup Completed Successfully!!! ## ########################################## For detailed configuration information, refer to the Content Services Switch Basic Configuration Guide.
Chapter 4 Configuring the CSS Using the Configuration Script To configure Layer 5 load balancing, enter 2. Which feature do you want to configure? [1] [2] [3] [4] Layer3 load balancing Layer5 load balancing Proxy cache Transparent cache Enter the number for the feature you want to configure: 2 To accept the script default values, press the Enter key at the prompts. Creating Layer5 load balancing Enter service name: [default= Server1] Enter service IP address: [default = 192.168.10.3] 192.168.3.
Chapter 4 Configuring the CSS Using the Configuration Script Showing the Running Config !Generated MAR 6 17:53:49 !**************** GLOBAL ***************** ip route 0.0.0.0 0.0.0.0 192.168.3.3 !**************** CIRCUIT **************** circuit VLAN1 ip address 192.168.3.6 255.255.255.0 !**************** SERVICE **************** service Server1 ip address 192.168.3.58 active !**************** OWNER ****************** owner L5_Owner content L3_Rule add service Server1 vip address 192.168.3.
Chapter 4 Configuring the CSS Using the Configuration Script Configuring Proxy Cache A proxy cache configuration enables the CSS to use a Virtual IP address (VIP) to load balance Web traffic to proxy cache servers based on domain name.
Chapter 4 Configuring the CSS Using the Configuration Script To accept the script default values, press the Enter key at the prompts. Creating Proxy Cache Configuration Enter service name: [default=Proxy_Cache1] Enter service IP address: [default = 192.168.10.3] 192.168.3.60 Create another service? [y/n]? n Enter Virtual IP address for Proxy_Rule: [default = 192.168.10.4] 192.168.3.
Chapter 4 Configuring the CSS Using the Configuration Script Showing the Running Config !Generated MAR 6 17:53:49 !**************** GLOBAL ***************** ip route 0.0.0.0 0.0.0.0 192.168.3.3 !**************** CIRCUIT **************** circuit VLAN1 ip address 192.168.3.6 255.255.255.0 !**************** SERVICE **************** service Proxy_Cache1 ip address 192.168.3.
Chapter 4 Configuring the CSS Using the Configuration Script Configuring Transparent Cache A transparent cache configuration enables the CSS to redirect cacheable HTTP traffic to transparent cache servers based on IP address and port (80). The CSS directs non-cacheable HTTP traffic to the origin servers.
Chapter 4 Configuring the CSS Using the Configuration Script To accept the script default values, press the Enter key at the prompts. Creating Transparent Cache Configuration Enter service name: [default = Transparent_Cache1] Enter service IP address: [default = 0.0.0.0] 192.168.3.7 Create another service? [y/n]? n Transparent caching can be configured to direct only cacheable content to the cache server. Non-cacheable content is sent directly to the origin server.
Chapter 4 Configuring the CSS Using the Configuration Script !**************** SERVICE **************** service Transparent_Cache1 ip address 192.168.3.
Chapter 4 Configuring the CSS Using the Configuration Script extension wav "Wave File audio/x-wav" extension gz "application/x-gzip" extension zip "ZIP file application/x-zip-compressed" !***************** OWNER ***************** owner Transparent_Owner content Transparent_Rule add service Transparent_Cache1 port 80 protocol tcp url "/*" eql Cacheable or url "/*" balance domain failover bypass application http active ########################################## ## Setup Completed Successfully!!! ## ########
Chapter 4 Configuring the CSS Using the Configuration Script Content Services Switch Getting Started Guide 4-18 78-11766-01
A P P E N D I X A Specifications This appendix contains the following sections that list specifications for the CSS 11050, CSS 11150, and CSS 11800: • Electrical Specifications • Environmental Specifications • Physical Specifications • Module Specifications • Internal Disk Module Specifications • Supported Protocols • DC Power Supply Safety Warnings • Lithium Battery Disposal Warnings Content Services Switch Getting Started Guide 78-11766-01 A-1
Appendix A Specifications Electrical Specifications Electrical Specifications Table A-1 describes the CSS 11050, CSS 11150, and CSS 11800 AC electrical specifications . Table A-1 AC Electrical Specification CSS 11050 or CSS 11150 CSS 11800 Input Voltage AC 100 to 240 VAC 50 to 60 Hz 100 to 240 VAC 50 to 60 Hz Current AC (max@ 100VAC) 3.
Appendix A Specifications Electrical Specifications AC Power Cord Country Requirements The CSS AC power cord is a three-prong IEC 320-C13 plug that grounds the unit and polarizes the connection. Table A-3 lists country requirements for plug types and ratings.
Appendix A Specifications Environmental Specifications Environmental Specifications Table A-4 describes the CSS 11050, CSS 11150, and CSS 11800 environmental specifications.
Appendix A Specifications Module Specifications Module Specifications Table A-6 describes module general specifications.
Appendix A Specifications Internal Disk Module Specifications Internal Disk Module Specifications This section provides the following specifications for the Internal Disk Module (IDM). • Power • General IDM Power Requirements Table A-7 describes the IDM power requirements. Table A-7 IDM Power Requirements Power Requirements Internal Disk Module +12V +/- 5% 1.2 Amps Max +5V +/- 5% .5 Amps Max IDM General Specifications Table A-8 defines IDM general specifications.
Appendix A Specifications Supported Protocols Supported Protocols The CSS supports the following protocols: • Transport • Network • Routing • Gateway • Application • Network Utilities • Network Management Transport The CSS supports the following transport protocols: • TCP • UDP Network The CSS supports the following network protocols: • Internet Protocol (IP) • ICMP • Address Resolution Protocol (ARP) • Inverse ARP Content Services Switch Getting Started Guide 78-11766-01 A-7
Appendix A Specifications Supported Protocols Routing The CSS supports the following routing protocols: • RIP I • RIP II • OSPF Version 2 Gateway The CSS supports Network Address Translation (NAT), per RFC 1631 gateway protocol. Application The CSS supports the following application protocols: • HTTP 1.0, HTTP 1.
Appendix A Specifications Supported Protocols Network Management The CSS supports the following network management protocols: • SNMP v1 • SNMP v2 Content Services Switch Getting Started Guide 78-11766-01 A-9
Appendix A Specifications DC Power Supply Safety Warnings DC Power Supply Safety Warnings Warning The DC power supply must be installed in restricted access areas only (for example, dedicated equipment rooms, equipment closets) in accordance with articles 110-16, 110-17, and 110-18 of the national electric code, ANSI/NFPA 70. Connect a DC CSS 11150 or CSS 11800 to a -48 VDC source that is electrically isolated from the AC power source and is reliably grounded to earth.
Appendix A Specifications Lithium Battery Disposal Warnings Lithium Battery Disposal Warnings The SCM contains a small lithium battery. Some jurisdictions restrict the ways in which items containing lithium batteries may be disposed. In particular, lithium batteries or products containing lithium batteries may never be disposed of in an unregulated fire. Other restrictions might apply. Warning Ultimate disposal of this product should be handled according to all national laws and regulations.
Appendix A Specifications Lithium Battery Disposal Warnings Content Services Switch Getting Started Guide A-12 78-11766-01
A P P E N D I X B Cable Pinouts This appendix contains the following sections that list pinouts for the connectors used with the CSS 11050, CSS 11150, and CSS 11800: • RJ-45 Fast Ethernet Connector Pinouts • RJ-45 RS-232 Serial Connector Pinouts • RJ-45 Timing BITS Connector Pinouts • RJ-45 Management Connector Pinouts RJ-45 Fast Ethernet Connector Pinouts Table B-1 lists the pinouts for the RJ-45 Fast Ethernet connectors on the: • CSS 11050 and CSS 11150 • Fast Ethernet Module Content Service
Appendix B Cable Pinouts RJ-45 RS-232 Serial Connector Pinouts Table B-1 RJ-45 Fast Ethernet Connector Pinouts Signal Name RJ-45 Fast Ethernet Pin Numbers Crossover Cable Pinouts RX + 1 3 RX - 2 6 TX + 3 1 Unconnected 4 4 Unconnected 5 5 TX - 6 2 Unconnected 7 7 Unconnected 8 8 When using the Fast Ethernet connectors to connect the CSS to a: • Server or a workstation, use a straight-through cable • Switch or a repeater, use a crossover cable RJ-45 RS-232 Serial Connector
Appendix B Cable Pinouts RJ-45 RS-232 Serial Connector Pinouts Table B-2 RJ-45 RS-232 Serial Connector Pinouts for the Console Port Signal Name Pin Number DTR - 1 TXD 2 RXD 3 RTS - 4 CTS - 5 DSR 6 GND 7 DCD - 8 Table B-3 lists the pinouts for the RJ-45 to DB-9 or to DB-25 console cables supplied in the CSS cable kit.
Appendix B Cable Pinouts RJ-45 RS-232 Serial Connector Pinouts Table B-4 lists the RJ-45 RS-232 Serial connector pinouts for the Diag port. Table B-4 RJ-45 RS-232 Serial Connector Pinouts for the Diag Port Signal Name Pin Number Not Used 1 TXD 2 RXD 3 Not Used 4 Not Used 5 Not Used 6 GND 7 Not Used 8 Table B-5 lists the RJ-45 RS-232 Serial connector pinouts for the Diag1 and Diag2 ports on the SFM2.
Appendix B Cable Pinouts RJ-45 Timing BITS Connector Pinouts RJ-45 Timing BITS Connector Pinouts Table B-6 lists the RJ-45 Timing BITS (Building Integrated Timing Supply) Clock connector pinouts on the SCM.
Appendix B Cable Pinouts RJ-45 Management Connector Pinouts Content Services Switch Getting Started Guide B-6 78-11766-01
A P P E N D I X C Troubleshooting This appendix provides general troubleshooting information for the CSS components. It includes the following sections: • Troubleshooting the Console Interface • Troubleshooting the CSS Power Supply • Troubleshooting the CSS 11800 Modules • Troubleshooting the Boot Process • Log File Information Information in this appendix applies to the CSS 11050, CSS 11150, and CSS 11800 Content Services Switches except where noted.
Appendix C Troubleshooting Troubleshooting the CSS Power Supply Table C-1 Troubleshooting the Console Interface Possible Problem Recommended Action Nothing appears on the screen. Ensure the RS-232 cable is securely connected to the console port. Characters appear on the screen, but are garbled. Verify that the CSS and the console settings match for baud rate, data bits, stop bits, and parity.
Appendix C Troubleshooting Troubleshooting the CSS 11800 Modules Table C-3 provides suggestions for correcting problems that may occur with the CSS 1800 power supplies (AC or DC). The power supply status LED is on the SCM. Table C-3 Troubleshooting the CSS 11800 Power Supply LED Name LED Status Possible Problem PS 1 PS 2 Off No power to primary power supply. Recommended Action Ensure unit has power. Check power switch, power cord, and power source. Fault in power supply. Replace the power supply.
Appendix C Troubleshooting Troubleshooting the CSS 11800 Modules Table C-4 Troubleshooting the CSS 11800 Modules Symptom Recommended Action System cannot identify module type. Remove the module and re-install it to reseat the module in the backplane connector. Reload the ADI file. System cannot find an image Reload the ADI file. for the module. Module failed diagnostic (according to the information in the Boot.log file). Replace the module.
Appendix C Troubleshooting Troubleshooting the Boot Process Troubleshooting the Boot Process During the boot process, the SCM downloads software to the SFM or SFM2 and the I/O modules. If the boot process cannot locate the correct files, the CSS logs an error in the Boot.log file. For information about the boot process, refer to Chapter 4, Configuring the CSS. Table C-5 provides suggestions for correcting problems that may occur during the boot process.
Appendix C Troubleshooting Log File Information Log File Information The CSS provides logging capabilities for debug and system monitoring by generating the log files described in Table C-6. Table C-6 CSS Log File Descriptions Log File Destination Default Location Alternate Location Records Boot.log Hard disk and console or flash disk and console None Results of the boot process. Boot.bak Hard disk and console or flash disk and console None Backup of a boot log file.
Appendix C Troubleshooting Log File Information By default, the CSS has boot logging and system logging enabled and writes the logged information to the log files on the hard disk or flash disk, depending on the type of storage in your CSS. The maximum size of a log file is 50 MB for hard disk-based systems and 10 MB for flash disk-based systems. Log file information is recorded as ASCII text. Note If the CSS disk fails, log and archive information cannot be saved to files on the disk.
Appendix C Troubleshooting Log File Information Content Services Switch Getting Started Guide C-8 78-11766-01
A P P E N D I X D Regulatory Information This appendix lists the regulatory agencies that have approved the content services switch (CSS 11050, CSS 11150, or CSS 11800). This appendix also includes a sample affidavit that you need to file with your telephone company concerning connecting customer premise equipment (CPE) to 1.544-Mbps services.
Appendix D Regulatory Information Canadian IC CS-03 Requirements Table D-1 Regulatory Standards Compliance Regulatory Standards Compliance Safety EMC Factory Approvals Regulatory Agency • UL 1950 • C-UL • EN60950 • GS Mark • FCC Part 15 • EN55022 • EN50082-1 • VCCI • UL • TUV • BABT Canadian IC CS-03 Requirements The Industry Canada label identifies certified equipment.
Appendix D Regulatory Information Canadian IC CS-03 Requirements Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Warning Users should not attempt to make electrical ground connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
Appendix D Regulatory Information FCC and Telephone Company Procedures and Requirements AVIS: L’indice d’ équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent étre raccordés a une interface. La terminaison d’ une interface téléphonique peut consister en une combinaison de quelques dispositifs, a la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
Appendix D Regulatory Information FCC and Telephone Company Procedures and Requirements This equipment produces electromagnetic energy at radio frequencies and, if not installed and operated in accordance with the manufacturer’s instructions as contained in this document, could cause interference to radio communications and/or interfere with the operation of other RF devices.
Appendix D Regulatory Information Example Affidavit (United States) Example Affidavit (United States) This is an example of the affidavit that needs to be filed with the Telco concerning connection of customer premise equipment (CPE) to 1.
Appendix D Regulatory Information Example Affidavit (United States) ( ) In lieu of the proceeding training requirements, the operator(s)/maintainer(s) is (are) under control of a supervisor trained in accordance with _____ (circle one) above. I agree to provide _________________________________ (name of Telco) with proper documentation to demonstrate compliance with the information as provided in the preceding paragraph, if so requested.
Appendix D Regulatory Information Example Affidavit (United States) Content Services Switch Getting Started Guide D-8 78-11766-01
I N D E X A C accessory kit 1-2 cabling AC electrical specifications A-2 Fast Ethernet Module 2-17 AC power cord Gigabit Ethernet Module 2-20 connecting CSS 11050 or CSS 11150 2-29 connecting CSS 11800 2-31 country requirements A-3 affidavit sample (United States) D-6 anti-static wrist strap 1-2 application protocol A-8 audience xv Switch Control Module 2-10 Canadian IC CS-03 requirements D-2 caution configuring Ethernet Management port IP address 3-7 hot swapping 1-18 connectors 2-17 CSS 11050 fr
Index content rule CSS 11800 description 4-2 chassis mounting key 1-10 purpose in life 4-2 front panel connectors and LEDs 2-14, 2-16, 2-17, 2-20, 2-22, 2-26 country requirements (AC power cord) A-3 installing as a rack-mount unit 1-9 CSS 11050 cabling 2-1 front panel connector and LEDs 2-2, 2-3 grounding 1-6 installation 1-6 module specifications A-5 shipping pallet 1-5 slot restrictions 1-16 unpacking 1-4 installing 1-6 LED definitions 2-4 D mounting brackets 1-8 rack-mounting 1-7 damage to
Index documentation G chapter contents xvi map xix gateway protocol A-8 related xvii Gigabit Ethernet Module set xvii cabling 2-20 symbols and conventions xx LED definitions 2-22 LEDs and connectors 2-20 E H electrical specifications A-2 electro-static discharge cautions 1-19 hardware initialization 3-9 hot swapping cautions 1-18 environmental specifications A-4 I F installation precautions 1-15 Fast Ethernet Module installing cabling 2-17 CSS 11050 1-6 LED definitions 2-20 CSS 11150 1-
Index LEDs 2-26 installing 1-15, 1-19 power requirements A-6 Internal Disk Module 2-26 specifications A-6 passive switchover 1-21 slot restrictions 1-16 specifications A-5 L troubleshooting 3-3 unpacking 1-18 LEDs warning (SCM battery) 1-21, 2-13 CSS 11050 front panel 2-2, 2-3 CSS 11050 rear panel 2-2 mounting brackets CSS 11150 front panel 2-6, 2-8 changing CSS 11800 brackets 1-10, 1-11 CSS 11150 rear panel 2-2 installing CSS 11050 1-7 Fast Ethernet Module 2-20 installing CSS 11150 1-7 G
Index pinouts RS-232 serial connector pinouts B-2 timing BITS connector pinouts B-5 RJ-45 fast Ethernet connector B-1 RJ-45 management connector B-5 routing protocol A-8 RJ-45 RS-232 serial connector B-2 RJ-45 timing BITS connector B-5 power cords connecting 2-28 country requirements A-3 power supply S safety warning 1-7, A-10 scripts disk directory 3-2 load balancing 3-3 service, owner, content rule 4-1 troubleshooting 3-2 shipment contents 1-2 protocols, supported A-7 to A-9 site requirements
Index Switch Control Module U cabling 2-12 LED definitions 2-16 LEDs and connectors 2-14 Switch Fabric Module (SFM and SFM2) unpacking CSS 11050 1-4 CSS 11150 1-4 LED definitions 2-26 CSS 11800 1-4 LEDs 2-22 modules 1-18 sys.
