CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1130AG Series Access Point Hardware Installation Guide September 2004 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
CISCO CONFIDENTIAL - Draft 1 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CISCO CONFIDENTIAL - Draft 1 CONTENTS Preface ix Audience Purpose ix ix Organization ix Conventions x Related Publications xii Obtaining Documentation xii Cisco.com xii Documentation CD-ROM xiii Ordering Documentation xiii Documentation Feedback xiii Obtaining Technical Assistance xiv Cisco.
Contents CISCO CONFIDENTIAL Installing the Access Point 2-1 Safety Information 2-2 FCC Safety Compliance Statement General Safety Guidelines 2-2 Warnings Draft 1 2-2 2-2 Unpacking the Access Point 2-3 Package Contents 2-3 Basic Installation Guidelines 2-3 Before Beginning the Installation 2-4 Access Point Layout and Connectors 2-4 Mounting Plate 2-5 Suspended Ceiling Adjustable T-Rail Clips Installation Summary 2-6 2-7 Opening the Access Point Cover 2-8 Mounting the Access Point 2-9 Mounting o
Contents CISCO CONFIDENTIAL Assigning Basic Settings 3-4 Default Settings on the Express Setup Page Protecting Your Wireless LAN Draft 1 3-8 3-8 Using the IP Setup Utility 3-9 Obtaining and Installing IPSU 3-9 Using IPSU to Find the Access Point’s IP Address 3-10 Using IPSU to Set the Access Point’s IP Address and SSID Assigning an IP Address Using the CLI 3-12 Using a Telnet Session to Access the CLI Using the Web-Browser Interface 3-12 4-1 Using the Web-Browser Interface for the First Time 4-2
Contents CISCO CONFIDENTIAL Troubleshooting Draft 1 6-1 Checking the Access Point LEDs 6-2 Checking Basic Settings 6-4 SSID 6-4 WEP Keys 6-4 Security Settings 6-4 Resetting to the Default Configuration Using the MODE Button 6-5 Using the Web Browser Interface 6-5 6-6 Reloading the Access Point Image 6-7 Using the MODE button 6-7 Web Browser Interface 6-8 Browser HTTP Interface 6-8 Browser TFTP Interface 6-8 Obtaining the Access Point Image File Obtaining the TFTP Server Software Translated Safety W
Contents CISCO CONFIDENTIAL Access Point Specifications - TBD Channels and Power Levels Draft 1 C-1 D-1 Channels and Maximum Power Levels D-2 IEEE 802.11b/g (2.4-GHz Band) D-2 IEEE 802.
Contents CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1130AG Series Access Point Hardware Installation Guide viii OL-6226-01
CISCO CONFIDENTIAL - Draft 1 Preface Audience This guide is for the networking professional who installs and manages the Cisco Aironet 1130AG Series Access Point, hereafter referred to as the access point. To use this guide, you should have experience working with the Cisco IOS software and be familiar with the concepts and terminology of wireless local area networks. Purpose This guide provides the information you need to install and configure basic settings for your access point.
Preface Conventions CISCO CONFIDENTIAL - Draft 1 Chapter 4, “Using the Web-Browser Interface,” describes how to use the web-browser interface to configure the access point. Chapter 5, “Using the Command-Line Interface,” describes how to use the command-line interface (CLI) to configure the access point. Chapter 6, “Troubleshooting,” provides troubleshooting procedures for basic problems with the access point.
Preface Conventions CISCO CONFIDENTIAL - Caution Warning Waarschuwing Draft 1 Means reader be careful. In this situation, you might do something that could result equipment damage or loss of data. This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.
Preface Related Publications CISCO CONFIDENTIAL Aviso Draft 1 Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos fisicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes.
Preface Obtaining Documentation CISCO CONFIDENTIAL - Draft 1 Documentation CD-ROM Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which may have shipped with your product. The Documentation CD-ROM is updated regularly and may be more current than printed documentation. The CD-ROM package is available as a single unit or through an annual or quarterly subscription. Registered Cisco.
Preface Obtaining Technical Assistance CISCO CONFIDENTIAL - Draft 1 Obtaining Technical Assistance Cisco provides Cisco.com, which includes the Cisco Technical Assistance Center (TAC) website, as a starting point for all technical assistance. Customers and partners can obtain online documentation, troubleshooting tips, and sample configurations from the Cisco TAC website. Cisco.
Preface Obtaining Technical Assistance CISCO CONFIDENTIAL - Draft 1 Locating the Product Serial Number The access point serial number is located on the bottom of the cabinet (refer to Figure 1).
Preface Obtaining Additional Publications and Information CISCO CONFIDENTIAL - Draft 1 Cisco TAC Escalation Center The Cisco TAC Escalation Center addresses priority level 1 or priority level 2 issues. These classifications are assigned when severe network degradation significantly impacts business operations. When you contact the TAC Escalation Center with a P1 or P2 problem, a Cisco TAC engineer automatically opens a case.
CISCO CONFIDENTIAL - Draft 1 C H A P T E R 1 Overview Cisco Aironet 1130AG Series Access Points provide a secure, affordable, and easy-to-use wireless LAN solution that combines mobility and flexibility with the enterprise-class features required by networking professionals. With a management system based on Cisco IOS software, the 1130 series access point is a Wi-Fi certified, wireless LAN transceiver. The access point contains two integrated radios: a 2.4-GHz radio (IEEE 802.
Chapter 1 Overview Hardware Features CISCO CONFIDENTIAL - Draft 1 Hardware Features This section describes access point features. Refer to Appendix C, “Access Point Specifications,” for a list of access point specifications.
Chapter 1 Overview Hardware Features CISCO CONFIDENTIAL - Draft 1 Ethernet Port The auto-sensing Ethernet port accepts an RJ-45 connector, linking the access point to your 10BASE-T or 100BASE-T Ethernet LAN. The access point can receive power through the Ethernet cable from a power injector, switch, or power patch panel. The Ethernet MAC address is printed on the label on the back of the access point. The port is located in a cable bay area that is hidden by the top cover (see Figure 1-1).
Chapter 1 Overview Hardware Features CISCO CONFIDENTIAL - Draft 1 The access point supports the following power sources: • Power module (supplied) • Inline power: – Cisco Aironet 1300 Series Power Injector (supplied) – An inline power capable switch, such as Cisco Catalyst 3500XL, 3550, 4500, or 6500 switches – An inline power patch panel, such as the Cisco Catalyst Inline Power Patch Panel – Other inline power switches supporting the IEEE 802.
Chapter 1 Overview Hardware Features CISCO CONFIDENTIAL - Draft 1 \ 1 Access point cover in open position 2 Security hasp adapter 3 Security padlock Cisco Aironet 1130AG Series Access Point Hardware Installation Guide OL-6226-01 1-5
Chapter 1 Overview Hardware Features CISCO CONFIDENTIAL • Note Security screw—The access point contains a security screw hole (see Figure 1-3) that can be used to attach the access point to the mounting plate to restrict access point removal. When a security-type screw (user supplied) is used, access to the mounting screws that attach the mounting plate is greatly restricted. The use of a security-type screw does not restrict access to the access point cables or the mode button.
Chapter 1 Overview Network Configuration Examples CISCO CONFIDENTIAL - Draft 1 Network Configuration Examples This section describes the access point’s role in three common wireless network configurations. The access point’s default configuration is as a root unit connected to a wired LAN or as the central unit in an all-wireless network. The repeater role requires a specific configuration.
Chapter 1 Overview Network Configuration Examples CISCO CONFIDENTIAL - Draft 1 Repeater Unit that Extends Wireless Range An access point can be configured as a stand-alone repeater to extend the range of your infrastructure or to overcome an obstacle that blocks radio communication. The repeater forwards traffic between wireless users and the wired LAN by sending packets to either another repeater or to an access point connected to the wired LAN.
Chapter 1 Overview Network Configuration Examples CISCO CONFIDENTIAL - Draft 1 Central Unit in an All-Wireless Network In an all-wireless network, an access point acts as a stand-alone root unit. The access point is not attached to a wired LAN; it functions as a hub linking all stations together. The access point serves as the focal point for communications, increasing the communication range of wireless users. Figure 1-6 shows an access point in an all-wireless network.
Chapter 1 Overview Network Configuration Examples CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1130AG Series Access Point Hardware Installation Guide 1-10 OL-6226-01
CISCO CONFIDENTIAL - Draft 1 C H A P T E R 2 Installing the Access Point This chapter describes the installation of the access point and includes these sections: • Safety Information, page 2-2 • Warnings, page 2-2 • Unpacking the Access Point, page 2-3 • Basic Installation Guidelines, page 2-3 • Before Beginning the Installation, page 2-4 • Installation Summary, page 2-7 • Opening the Access Point Cover, page 2-8 • Mounting the Access Point, page 2-9 • Attaching the Access Point to the
Chapter 2 Installing the Access Point Safety Information CISCO CONFIDENTIAL - Draft 1 Safety Information Follow the guidelines in this section to ensure proper operation and safe use of the access point. FCC Safety Compliance Statement The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment.
Chapter 2 Installing the Access Point Unpacking the Access Point CISCO CONFIDENTIAL - Draft 1 Unpacking the Access Point Follow these steps to unpack the access point: Step 1 Open the shipping container and carefully remove the contents. Step 2 Return all packing materials to the shipping container and save it. Step 3 Ensure that all items listed in the “Package Contents” section are included in the shipment. Check each item for damage.
Chapter 2 Installing the Access Point Before Beginning the Installation CISCO CONFIDENTIAL - Draft 1 Before Beginning the Installation Before you begin the installation process, please refer to these sections to become familiar with the access point and the mounting hardware: • “Access Point Layout and Connectors” section on page 2-4 • “Mounting Plate” section on page 2-5 • “Suspended Ceiling Adjustable T-Rail Clips” section on page 2-6 Access Point Layout and Connectors Figure 2-1 identifies the
Chapter 2 Installing the Access Point Before Beginning the Installation CISCO CONFIDENTIAL - Draft 1 Mounting Plate The access point mounting plate is designed to accomodate multiple mounting methods. The mounting holes on the plate are marked so you can easily identify the correct holes for a specific mounting method. You can use the mounting plate as a template to mark the locations for the cable hole and the mounting holes for your wall or ceiling installation.
Chapter 2 Installing the Access Point Before Beginning the Installation CISCO CONFIDENTIAL • Draft 1 Padlock hole—used to attach a padlock to secure the access point to the mounting plate. Compatible padlocks are Master Lock models 120T and 121T or equivalent. The security hasp adapter can also be used with the padlock for increase security protection.
Chapter 2 Installing the Access Point Installation Summary CISCO CONFIDENTIAL - Draft 1 The adjustable T-rail clip attaches to the mounting plate using four 6x32x1/4 inch flat head screws.
Chapter 2 Installing the Access Point Opening the Access Point Cover CISCO CONFIDENTIAL - Draft 1 Opening the Access Point Cover The top cover provides access to the access point cable bay area containing the power connector, Ethernet port, console serial port, the mode button, and the Ethernet and Radio LEDs. Caution Do not attempt to pry open or lift the top cover of the access point, because you could damage the cover.
Chapter 2 Installing the Access Point Mounting the Access Point CISCO CONFIDENTIAL Step 3 Draft 1 Continue to slowly slide the cover back across the access point until you reach the cover stop (see Figure 2-6).
Chapter 2 Installing the Access Point Mounting the Access Point CISCO CONFIDENTIAL - Draft 1 Mounting on a Horizontal or Vertical Surface Follow these steps to mount the access point on a horizontal or vertical surface: Step 1 Use the mounting plate as a template to mark the locations of the two mounting holes (labled with an X) and the location of the cable access hole (see Figure 2-7).
Chapter 2 Installing the Access Point Mounting the Access Point CISCO CONFIDENTIAL - Draft 1 Step 5 Position the mounting plate over the wall anchors or the drilled holes. Step 6 Insert two 8x32x1inch pan head screws in the X mounting holes and tightening. To attach the access point to the mounting plate, see “Attaching the Access Point to the Mounting Plate” section on page 2-15.
Chapter 2 Installing the Access Point Mounting the Access Point CISCO CONFIDENTIAL - Draft 1 Step 2 Select the appropriate adjustable T-rail clip for your suspended ceiling and open the clip to the maximum (see Figure 2-4). Step 3 Unscrew the two T-rail locking set screws to enable placing the clip over a T-rail. Step 4 Place the T-rail clip over the T-rail and close the T-rail clip (see Figure 2-4). Step 5 Tighten the two T-rail locking set screws to prevent the T-rail clip from moving.
Chapter 2 Installing the Access Point Mounting Above a Suspended Ceiling CISCO CONFIDENTIAL - Draft 1 Mounting Above a Suspended Ceiling The access point mounting bracket is designed to be integrated into the T-bar grid above the tiles of a suspended ceiling. The access point uses a T-bar box hanger (not supplied) such as the Erico Caddy 512 or B-Line BA12 and should be oriented just above the top surface of a standard 5/8-in. (1.59 cm) ceiling tile.
Chapter 2 Installing the Access Point Mounting Above a Suspended Ceiling CISCO CONFIDENTIAL - Draft 1 Step 4 Configure the ends of the T-bar box hanger to allow for maximum clearance above the ceiling tile. See the illustration above. Step 5 Attach the T-rail clips on the each end of the T-bar box hanger to the ceiling grid T-rails. Make sure the clips are securely attached to the T-rails.
Chapter 2 Installing the Access Point Attaching the Access Point to the Mounting Plate CISCO CONFIDENTIAL - Draft 1 Rotating the Cisco Logo The Cisco logo on the top of the unit can be rotated to correctly position the logo for any mounting arrangement, such as when the unit is mounted on a vertical wall, the logo should oriented with the Cisco Systems positioned on top. The logo should always be oriented to ease reading.
Chapter 2 Installing the Access Point Attaching the Access Point to the Mounting Plate CISCO CONFIDENTIAL Step 3 Draft 1 In the cable bay area, line up the visible access point keyhole with the mounting plate keyhole clip located near the security padlock hole (see Figure 2-12).
Chapter 2 Installing the Access Point Connecting the Ethernet and Power Cables CISCO CONFIDENTIAL - Draft 1 Connecting the Ethernet and Power Cables The access point receives power through the Ethernet cable or an external power module. Figure 2-13 shows the power options for the access point.
Chapter 2 Installing the Access Point Connecting the Ethernet and Power Cables CISCO CONFIDENTIAL - Draft 1 Connecting to an Ethernet Network with an Inline Power Source Caution The Cisco Aironet Power Injectors are not tested to UL 2043 and should not be placed in a building's environmental air space, such as above suspended ceilings.
Chapter 2 Installing the Access Point Securing the Access Point CISCO CONFIDENTIAL - Draft 1 Connecting to an Ethernet Network with Local Power Follow these steps to connect the access point to an Ethernet LAN when you are using a local power source: Step 1 If necessary, open the access point cover (see the “Opening the Access Point Cover” section on page 2-8). Step 2 Pull the Category 5 Ethernet cable and the power module cable out of the access point cable bay area approximately 1 foot.
Chapter 2 Installing the Access Point Securing the Access Point CISCO CONFIDENTIAL - Draft 1 Securing the Access Point to the Mounting Plate The mounting plate contains a security padlock hole and a security screw hole to enable you to secure your access point to the mounting plate to restrict it’s removal. You can use a security-type screw (that you provide) to attach the access point to the mounting plate using the security screw hole (see Figure 2-12).
Chapter 2 Installing the Access Point Powering Up the Access Point CISCO CONFIDENTIAL - Draft 1 Step 5 Position the padlock into the padlock area. Step 6 Close the access point cover by sliding it over the security hasp adapter until you hear a click. Powering Up the Access Point When power is applied to the access point, it begins a routine power-up sequence that you can monitor by observing the Status LED on top of the access point.
Chapter 2 Installing the Access Point Powering Up the Access Point CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1130AG Series Access Point Hardware Installation Guide 2-22 OL-6226-01
CISCO CONFIDENTIAL - Draft 1 C H A P T E R 3 Configuring the Access Point for the First Time This chapter describes how to configure basic settings on your access point for the first time. The contents of this chapter are similar to the instructions in the quick start guide that shipped with your access point.
Chapter 3 Configuring the Access Point for the First Time Before You Start CISCO CONFIDENTIAL - Draft 1 Before You Start Before you install the access point, make sure you are using a computer connected to the same network as the access point, and obtain the following information from your network administrator: • A system name for the access point • The case-sensitive wireless service set identifiers (SSIDs) for your 802.11g and 02.
Chapter 3 Configuring the Access Point for the First Time Obtaining and Assigning an IP Address CISCO CONFIDENTIAL - Draft 1 Step 6 Click System Configuration and the System Configuration screen appears. Step 7 Click the Reset to Defaults button. Note If the access point is configured with a static IP address, the IP address does not change.
Chapter 3 Configuring the Access Point for the First Time Assigning Basic Settings CISCO CONFIDENTIAL - Draft 1 Figure 3-1 shows the console port location. Figure 3-1 1 Note Step 3 Console Port Location Console port The Cisco part number for the DB-9 to RJ-45 serial cable is AIR-CONCAB1200. Browse to http://www.cisco.com/go/marketplace to order a serial cable. Set up a terminal emulator on your PC to communicate with the access point.
Chapter 3 Configuring the Access Point for the First Time Assigning Basic Settings CISCO CONFIDENTIAL - Draft 1 Figure 3-2 shows the Summary Status page.
Chapter 3 Configuring the Access Point for the First Time Assigning Basic Settings CISCO CONFIDENTIAL Step 5 Click Express Setup. The Express Setup screen appears. Figure 3-3 shows the Express Setup page. Figure 3-3 Step 6 Draft 1 Express Setup Page Enter the configuration settings you obtained from your system administrator. The configurable settings include: • System Name— The system name, while not an essential setting, helps identify the access point on your network.
Chapter 3 Configuring the Access Point for the First Time Assigning Basic Settings CISCO CONFIDENTIAL • Note Draft 1 IP Address—Use this setting to assign or change the access point’s IP address. If DHCP is enabled for your network, leave this field blank. If the access point’s IP address changes while you are configuring the access point using the web-browser interface or a Telnet session over the wired LAN, you lose your connection to the access point.
Chapter 3 Configuring the Access Point for the First Time Assigning Basic Settings CISCO CONFIDENTIAL Step 7 Draft 1 Click Apply to save your settings. If you changed the IP address, you lose your connection to the access point. Browse to the new IP address to reconnect to the access point. Your access point is now running but probably requires additional configuring to conform to your network’s operational and security requirements.
Chapter 3 Configuring the Access Point for the First Time Protecting Your Wireless LAN CISCO CONFIDENTIAL - Draft 1 Protecting Your Wireless LAN After you assign basic settings to your access point, you must configure security settings to prevent unauthorized access to your network. Because it is a radio device, the access point can communicate beyond the physical boundaries of your building.
Chapter 3 Configuring the Access Point for the First Time Using the IP Setup Utility CISCO CONFIDENTIAL - Draft 1 Step 10 Double-click IPSUvxxxxxx.exe in the temporary directory to expand the file. Step 11 Double-click Setup.exe and follow the steps provided by the installation wizard to install IPSU. The IPSU icon appears on your computer desktop.
Chapter 3 Configuring the Access Point for the First Time Using the IP Setup Utility CISCO CONFIDENTIAL - Draft 1 Using IPSU to Set the Access Point’s IP Address and SSID If you want to change the default IP address (10.0.0.1) of the access point, you can use IPSU. You can also set the access point’s SSID at the same time. Note IPSU can change the access point’s IP address and SSID only from their default settings. After the IP address and SSID have been changed, IPSU cannot change them again.
Chapter 3 Configuring the Access Point for the First Time Assigning an IP Address Using the CLI CISCO CONFIDENTIAL - Draft 1 Step 6 Click Set Parameters to change the access point’s IP address and SSID settings. Step 7 Click Exit to exit IPSU. Assigning an IP Address Using the CLI When you connect the access point to the wired LAN, the access point links to the network using a bridge virtual interface (BVI) that it creates automatically.
CISCO CONFIDENTIAL - Draft 1 C H A P T E R 4 Using the Web-Browser Interface This chapter describes the web-browser interface that you can use to configure the access point.
Chapter 4 Using the Web-Browser Interface Using the Web-Browser Interface for the First Time CISCO CONFIDENTIAL - Draft 1 Using the Web-Browser Interface for the First Time Use the access point’s IP address to browse to the management system. See the “Obtaining and Assigning an IP Address” section on page 3-3 for instructions on assigning an IP address to the access point. Follow these steps to begin using the web-browser interface: Step 1 Start your Internet browser.
Chapter 4 Using the Web-Browser Interface Using the Management Pages in the Web-Browser Interface CISCO CONFIDENTIAL - Draft 1 Figure 4-1 shows the web-browser interface home page.
Chapter 4 Using the Web-Browser Interface Using the Management Pages in the Web-Browser Interface CISCO CONFIDENTIAL - Draft 1 Using Action Buttons Table 4-1 lists the page links and buttons that appear on most management pages.
Chapter 4 Using the Web-Browser Interface Using Online Help CISCO CONFIDENTIAL - Draft 1 Character Restrictions in Entry Fields Because the access point uses Cisco IOS software, there are certain characters that you cannot use in the entry fields on the web-browser interface. Table 4-2 lists the prohibited characters and the fields in which you cannot use them.
Chapter 4 Using the Web-Browser Interface Using Online Help CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1130AG Series Access Point Hardware Installation Guide 4-6 OL-6226-01
CISCO CONFIDENTIAL - Draft 1 C H A P T E R 5 Using the Command-Line Interface This chapter describes the IOS command-line interface (CLI) that you can use to configure your access point.
Chapter 5 Using the Command-Line Interface IOS Command Modes CISCO CONFIDENTIAL - Draft 1 IOS Command Modes The Cisco IOS user interface is divided into many different modes. The commands available to you depend on which mode you are currently in. Enter a question mark (?) at the system prompt to obtain a list of commands available for each command mode. Refer to the Cisco IOS Command Reference for Cisco Aironet Access Points and Bridges for a list of the supported Cisco IOS commands.
Chapter 5 Using the Command-Line Interface Getting Help CISCO CONFIDENTIAL - Draft 1 Getting Help You can enter a question mark (?) at the system prompt to display a list of commands available for each command mode. You can also obtain a list of associated keywords and arguments for any command, as shown in Table 5-2. Table 5-2 Help Summary Command Purpose help Obtains a brief description of the help system in any command mode.
Chapter 5 Using the Command-Line Interface Understanding CLI Messages CISCO CONFIDENTIAL - Draft 1 Configuration commands can also have a default form. The default form of a command returns the command setting to its default. Most commands are disabled by default, so the default form is the same as the no form. However, some commands are enabled by default and have variables set to certain default values.
Chapter 5 Using the Command-Line Interface Using Editing Features CISCO CONFIDENTIAL - Draft 1 The range is from 0 to 256. Beginning in line configuration mode, enter this command to configure the number of command lines the access point records for all sessions on a particular line: ap(config-line)# history [size number-of-lines] The range is from 0 to 256.
Chapter 5 Using the Command-Line Interface Using Editing Features CISCO CONFIDENTIAL - Draft 1 Enabling and Disabling Editing Features Although enhanced editing mode is automatically enabled, you can disable it.
Chapter 5 Using the Command-Line Interface Using Editing Features CISCO CONFIDENTIAL Table 5-5 Draft 1 Editing Commands Through Keystrokes (continued) Capability Keystroke1 Purpose Capitalize or lowercase words or capitalize a set of letters. Esc C Capitalize at the cursor. Esc L Change the word at the cursor to lowercase. Esc U Capitalize letters from the cursor to the end of the word. Designate a particular keystroke as Ctrl-V or Esc Q an executable command, perhaps as a shortcut.
Chapter 5 Using the Command-Line Interface Searching and Filtering Output of show and more Commands CISCO CONFIDENTIAL - Draft 1 After you complete the entry, press Ctrl-A to check the complete syntax before pressing the Return key to execute the command. The dollar sign ($) appears at the end of the line to show that the line has been scrolled to the right: ap(config)# access-list 101 permit tcp 131.108.2.5 255.255.255.0 131.108.
Chapter 5 Using the Command-Line Interface Accessing the CLI CISCO CONFIDENTIAL - Note Draft 1 In Windows 2000, the Telnet window does not contain drop-down menus. To start the Telnet session in Windows 2000, type open followed by the access point’s IP address. Step 3 In the Host Name field, type the access point’s IP address and click Connect. Step 4 At the username and password prompts, enter your administrator username and password.
Chapter 5 Using the Command-Line Interface Accessing the CLI CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1130AG Series Access Point Hardware Installation Guide 5-10 OL-6226-01
CISCO CONFIDENTIAL - Draft 1 C H A P T E R 6 Troubleshooting This chapter provides troubleshooting procedures for basic problems with the access point. For the most up-to-date, detailed troubleshooting information, refer to the Cisco TAC website at the following URL (select Product Support > Wireless > Wireless LAN): http://www.cisco.
Chapter 6 Troubleshooting Checking the Access Point LEDs CISCO CONFIDENTIAL - Draft 1 Checking the Access Point LEDs If your access point is not working properly, check the Status LED on the top panel or the Ethernet and Radio LEDs in the cable bay area. You can use the LED indications to quickly assess the unit’s status. Figure 6-1 shows the access point LEDs.
Chapter 6 Troubleshooting Checking the Access Point LEDs CISCO CONFIDENTIAL - Draft 1 Cable Bay Area Top of Unit Message type Ethernet LED Radio LED Status LED Meaning Association status n/a n/a Light green Normal operating condition, but no wireless client devices are associated with the unit. n/a n/a Sky blue Normal operating condition, at least one wireless client device is associated with the unit. Green n/a n/a Ethernet link is operational.
Chapter 6 Troubleshooting Checking Basic Settings CISCO CONFIDENTIAL - Draft 1 Cable Bay Area Top of Unit Message type Ethernet LED Radio LED Status LED Meaning IOS errors Blinking amber n/a n/a Transmit or receive Ethernet errors. n/a Blinking amber n/a Maximum retries or buffer full occurred on the radio. Red Red Orange Software failure; try disconnecting and reconnecting unit power. n/a n/a Orange General warning, insufficient inline power.
Chapter 6 Troubleshooting Low Power Condition CISCO CONFIDENTIAL - Draft 1 Security Settings Wireless clients attempting to authenticate with your access point must support the same security options configured in the access point, such as EAP or LEAP, MAC address authentication, Message Integrity Check (MIC), WEP key hashing, and 802.1X protocol versions.
Chapter 6 Troubleshooting Running the Carrier Busy Test CISCO CONFIDENTIAL Step 5 Draft 1 Click Start to begin the carrier busy test. When the test completes, the results are displayed on the screen. For each of the channel center frequencies, the test produces a value indicating the percentage of time that the channel is busy.
Chapter 6 Troubleshooting Running the Ping/Link Test CISCO CONFIDENTIAL - Draft 1 Running the Ping/Link Test You can use the ping or link test to evaluate the link to and from an associated wireless device. The ping or link test provides two modes of operation: a. Perform a test using a specified number of packets and then display the test results. b. Perform a test that continuously operates until you stop the test and then displays the test results.
Chapter 6 Troubleshooting Resetting to the Default Configuration CISCO CONFIDENTIAL - Draft 1 Resetting to the Default Configuration If you forget the password that allows you to configure the access point, you may need to completely reset the configuration. You can use the MODE button on the access point or the web-browser interface. Note The following steps reset all configuration settings to factory defaults, including passwords, WEP keys, the IP address, and the SSID.
Chapter 6 Troubleshooting Reloading the Access Point Image CISCO CONFIDENTIAL Step 7 Click the Reset to Defaults button. Note Step 8 Draft 1 If the access point is configured with a static IP address, the IP address does not change. After the access point reboots, you must reconfigure the access point by using the Web browser interface, the Telnet interface, or IOS commands.
Chapter 6 Troubleshooting Reloading the Access Point Image CISCO CONFIDENTIAL - Draft 1 Step 9 Hold the MODE button approximately 20 to 30 seconds, and release the MODE button. Step 10 After the access point reboots, you must reconfigure the access point by using the Web interface, the Telnet interface, or IOS commands. Web Browser Interface You can also use the Web browser interface to reload the access point image file.
Chapter 6 Troubleshooting Obtaining the Access Point Image File CISCO CONFIDENTIAL - Draft 1 Step 4 Enter the access point password in the Password field and press Enter. The Summary Status page appears. Step 5 Click the System Software tab and then click Software Upgrade. The HTTP Upgrade screen appears. Step 6 Click the TFTP Upgrade tab. Step 7 Enter the IP address for the TFTP server in the TFTP Server field. Step 8 Enter the file name for the access point image file (such as c1130-k9w7-tar.
Chapter 6 Troubleshooting Obtaining the TFTP Server Software CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1130AG Series Access Point Hardware Installation Guide 6-12 OL-6226-01
CISCO CONFIDENTIAL - Draft 1 A P P E N D I X A Translated Safety Warnings This appendix provides translations of the safety warnings that appear in this publication. These translated warnings apply to other documents in which they appear in English.
Appendix A Translated Safety Warnings Statement 245B—Explosive Device Proximity Warning CISCO CONFIDENTIAL - Draft 1 Statement 245B—Explosive Device Proximity Warning Warning Waarschuwing Varoitus Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.
Appendix A Translated Safety Warnings Statement 332—Antenna Installation Warning CISCO CONFIDENTIAL - Draft 1 Statement 332—Antenna Installation Warning Warning In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons.
Appendix A Translated Safety Warnings Statement 1001—Work During Lightning Activity Warning CISCO CONFIDENTIAL - Draft 1 Statement 1001—Work During Lightning Activity Warning Warning Waarschuwing Varoitus Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001 Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan te sluiten of te ontkoppelen.
Appendix A Translated Safety Warnings Statement 1004—Installation Instructions Warning CISCO CONFIDENTIAL - Draft 1 Statement 1004—Installation Instructions Warning Warning Waarschuwing Varoitus Read the installation instructions before connecting the system to the power source. Statement 1004 Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit. Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.
Appendix A Translated Safety Warnings Statement 1005—Circuit Breaker (15A) Warning CISCO CONFIDENTIAL - Draft 1 Statement 1005—Circuit Breaker (15A) Warning Warning Waarschuwing Varoitus This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 15A Statement 1005 Dit product is afhankelijk van de installatie van het gebouw voor beveiliging tegen kortsluiting (overstroom).
Appendix A Translated Safety Warnings Statement 1005—Circuit Breaker (15A) Warning CISCO CONFIDENTIAL - Draft 1 15A 15A 15A Cisco Aironet 1130AG Series Access Point Hardware Installation Guide OL-6226-01 A-7
Appendix A Translated Safety Warnings Statement 1005—Circuit Breaker (15A) Warning CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1130AG Series Access Point Hardware Installation Guide A-8 OL-6226-01
CISCO CONFIDENTIAL - Draft 1 A P P E N D I X B Declarations of Conformity and Regulatory Information This appendix provides declarations of conformity and regulatory information for the Cisco Aironet 1130 Series Access Points.
Appendix B Manufacturers Federal Communication Commission Declaration of Conformity Statement CISCO CONFIDENTIAL - Declarations of Conformity and Regulatory Information Draft 1 Manufacturers Federal Communication Commission Declaration of Conformity Statement Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Model: AIR-AP1131AG-A-K9 FCC Certification number: LDK102054 Manufacturer: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA This device complies with Part 15 rules.
Appendix B Declarations of Conformity and Regulatory Information Department of Communications—Canada CISCO CONFIDENTIAL - Draft 1 Department of Communications—Canada Model: AIR-AP1131AG-A-K9 Certification number: 2461B-102054 Canadian Compliance Statement This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.
Appendix B Declarations of Conformity and Regulatory Information European Community, Switzerland, Norway, Iceland, and Liechtenstein CISCO CONFIDENTIAL - Draft 1 Español: Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directive 1999/5/EC. Έλληνας: Αυτός ο εξοπλισµός συµµορφώνεται µε τις ουσιώδεις απαιτήσεις και τις λοιπές διατάξεις της Οδηγίας 1999/5/EΚ.
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity for RF Exposure CISCO CONFIDENTIAL - Draft 1 49325 The following CE mark is affixed to the access point with a 2.4 GHz radio and a 54 Mbps, 5 GHz radio: Declaration of Conformity for RF Exposure The radio has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, and 15.
Appendix B Declarations of Conformity and Regulatory Information Guidelines for Operating Cisco Aironet Access Points in Japan CISCO CONFIDENTIAL - Draft 1 Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English.
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity Statements CISCO CONFIDENTIAL - Draft 1 Declaration of Conformity Statements All the Declaration of Conformity statements related to this product can be found at the following URL: http://www.ciscofax.
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity Statements CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1130AG Series Access Point Hardware Installation Guide B-8 OL-6226-01
CISCO CONFIDENTIAL - Draft 1 A P P E N D I X C Access Point Specifications This appendix provides technical specifications for the Cisco Aironet 1130AG Series Access Point. Table C-1 lists the technical specifications for the access point. Table C-1 Access Point Specifications Category 802.11b Radio Specifications 802.11g Radio Specifications 802.11a Radio Specifications Size 7.53 in. W x 7.53 in. D x 1.31 in. H 19.13 cm W x 19.13 cm D x 3.
Appendix C CISCO CONFIDENTIAL Table C-1 Access Point Specifications Draft 1 Access Point Specifications (continued) Category 802.11b Radio Specifications 802.11g Radio Specifications 802.11a Radio Specifications Power Output 100 mW (20 dBm) 50 mW (17 dBm) 25 mW (14 dBm) 10 mW (11 dBm) 5 mW (8 dBm) 3 mW (5 dBm) 1 mW (2 dBm) 0.5 mW (-1 dBm) 50 mW (17 dBm) 25 mW (14 dBm) 10 mW (11 dBm) 5 mW (8 dBm) 3 mW (5 dBm) 1 mW (2 dBm) 0.
Appendix C Access Point Specifications CISCO CONFIDENTIAL Table C-1 Draft 1 Access Point Specifications (continued) Category 802.11b Radio Specifications Safety Designed to meet: Radio Approvals 802.11g Radio Specifications 802.11a Radio Specifications • CSN/CSA 22.2 No. 60950 • UL 2043 (Plenum rating) • UL 60950 Third Edition • IEC 60950 Second Edition, including Amendments 1-4 with all deviations • EN 60950 Second Edition, including Amendments 1-4 FCC Part 15.
Appendix C CISCO CONFIDENTIAL - Access Point Specifications Draft 1 Cisco Aironet 1130AG Series Access Point Hardware Installation Guide C-4 OL-6226-01
CISCO CONFIDENTIAL - Draft 1 A P P E N D I X D Channels and Power Levels This appendix lists the IEEE 802.11b/g (2.4-GHz) and the IEEE 802.11a (5-GHz) channels and maximum power levels supported by the world’s regulatory domains.
Appendix D Channels and Power Levels Channels and Maximum Power Levels CISCO CONFIDENTIAL - Draft 1 Channels and Maximum Power Levels IEEE 802.11b/g (2.4-GHz Band) An improper combination of power level and antenna gain can result in equivalent isotropic radiated power (EIRP) above the amount allowed per regulatory domain. Table D-1 indicates the channel identifiers, channel center frequencies, and maximum power levels for each channel allowed by the regulatory domains: .
Appendix D Channels and Power Levels Channels and Maximum Power Levels CISCO CONFIDENTIAL - Draft 1 IEEE 802.11a (5-GHz Band) An improper combination of power level and antenna gain can result in equivalent isotropic radiated power (EIRP) above the amount allowed per regulatory domain. All channel sets are restricted to indoor usage except the Americas (–A), which allows for indoor and outdoor use on channels 52 through 64 in the United States.
Appendix D Channels and Power Levels Channels and Maximum Power Levels CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1130AG Series Access Point Hardware Installation Guide D-4 OL-6226-01
CISCO CONFIDENTIAL - Draft 1 A P P E N D I X E Console Cable Pinouts This appendix identifies the pinouts for the serial console cable that connects to the access point’s serial console port.
Appendix E Console Cable Pinouts Overview CISCO CONFIDENTIAL - Draft 1 Overview The access point requires a special serial cable that connects the access point serial console port (RJ-45 connector) to your PC’s COM port (DB-9 connector). This cable can be purchased from Cisco (part number AIR-CONCAB1200) or can be built using the pinouts in this appendix.
CISCO CONFIDENTIAL - Draft 1 GLOSSARY 802.11 The IEEE standard that specifies carrier sense media access control and physical layer specifications for 1- and 2-megabit-per-second (Mbps) wireless LANs operating in the 2.4-GHz band. 802.11a The IEEE standard that specifies carrier sense media access control and physical layer specifications for wireless LANs operating in the 5-GHz frequency band. 802.
Glossary CISCO CONFIDENTIAL - Draft 1 BPSK A modulation technique used by IEEE 802.11b-compliant wireless LANs for transmission at 1 Mbps. broadcast packet A single data message (packet) sent to all addresses on the same subnet. C CCK Complementary code keying. A modulation technique used by IEEE 802.11b-compliant wireless LANs for transmission at 5.5 and 11 Mbps. cell The area of radio range or coverage in which the wireless devices can communicate with the base station.
Glossary CISCO CONFIDENTIAL - Draft 1 E EAP Extensible Authentication Protocol. An optional IEEE 802.1x security feature ideal for organizations with a large user base and access to an EAP-enabled Remote Authentication Dial-In User Service (RADIUS) server. Ethernet The most widely used wired local area network. Ethernet uses carrier sense multiple access (CSMA) to allow computers to share a network and operates at 10, 100, or 1000 Mbps, depending on the physical layer used.
Glossary CISCO CONFIDENTIAL - Draft 1 M MAC Media Access Control address. A unique 48-bit number used in Ethernet data packets to identify an Ethernet device, such as an access point or your client adapter. modulation Any of several techniques for combining user information with a transmitter’s carrier signal. multipath The echoes created as a radio signal bounces off of physical objects. multicast packet A single data message (packet) sent to multiple addresses.
Glossary CISCO CONFIDENTIAL - Draft 1 roaming A feature of some Access Points that allows users to move through a facility while maintaining an unbroken connection to the LAN. RP-TNC A connector type unique to Cisco Aironet radios and antennas. Part 15.203 of the FCC rules covering spread spectrum devices limits the types of antennas that may be used with transmission equipment.
Glossary CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1130AG Series Access Point Hardware Installation Guide GL-6 OL-6226-01
CISCO CONFIDENTIAL - Draft 1 INDEX terminal emulator settings A 3-4 command-line interface abbreviating commands access point image 5-3 See CLI 6-7 command modes antenna 5-2 commands connectors C-2 abbreviating Apply button 4-4 no and default connectors Back button 4-4 basic settings, checking 5-3 C-1, C-2 console port B 5-3 E-2 D 6-4 data rates C-2 declarations of conformity C B-1 default, configuration, resetting Cancel button Cisco TAC default commands 4-4 6-5 5-3
Index CISCO CONFIDENTIAL frequencies D-2, D-3 frequency range Draft 1 N C-2 no commands 5-3 G O global configuration mode 5-2 OK button 4-4 operating temperature C-1 H help, for the command line 5-3 P history changing the buffer size package contents 5-4 2-3 described 5-4 password reset disabling 5-5 pinouts, serial cable recalling commands Home button connecting 4-4 input I 6-2 C-1 installation guidelines C-1 C-2 power level, maximum D-2 privileged EXEC mode 5-2 2-3
Index CISCO CONFIDENTIAL SSH Communications Security, Ltd.
Index CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1130AG Series Access Point Hardware Installation Guide IN-4 OL-6226-01
