Section 1 1.0 Introduction This document provides reference information for the evaluation testing of an internal modem based on Host Signal Processing Data/Fax/Voice Modem Technology. The HSP Modem™ evaluation card eliminates the redundant hardware parts found in most modems today. These include the data pump, a controller, an additional HART and external memory as required in a conventional approach.
22 HSP PCI Modem™ Setup using Windows 95 OEM Service Release 2 The HSP Modem™ driver will automatically handle all variations of CPU types. This eliminates the problem of poor performance that results from installing the incorrect driver. The driver will take advantage of the MMX enhancements if available 1. if another HSP Modem™ driver was previously installed, be sure te remove the software by following the appropriate Installation Procedure provided in the prior manual. When the computer is turned off.
3. Type 4. o complete the installation.
Communications Port Change: The installation program will automatically attach the HSP Modem™ to Com Port 5 or higher. Since certain applications require Com Ports 1-4, the Com Port can be changed by following the procedure outlined below. 1. Click SP Modem” under front Panel” 228100BC Accessibility Add New Add/Remove Date/Time Options Hardware Programs 9m x ad Ur splay Forts [EAGER intent Joystick “2 3 0% Keyboard Modems Mouse Multimedia Network Passwords PC Card Power Printers (PCMCIA 2.
Installation: The HSP Modem ™ can be uninstalled by using the following procedure. 1. Click SP Modem” under control Panel” [eT Ld 328¢00BC Accessibly Add New Option: Hardware Programs 9 Bx Q Display Foils Interment a O 9 Keyboard Mal Moderns 33 FS Network Passwords PC Card Printers {POMPOSITY 2. Click uninstall. The installation program will automatically remove the HSP ‘Modem™ from the system.
HSP PCI Modem™ Setup using Windows 98 The HSP Modem™ will automatically handle ail variations of CPU types. This eliminates the problem of poor performance that results from installing the incorrect driver. The driver will take advantage of the MMX enhancements if available. 1. 2. Windows will search for the driver.
3. Choose apply disk drives” and click ext” Continue to follow the lizard” instructions ro complete the installation process. a) as combustible QU 4. After the installation is complete, the following modem listing should be shown under doer Properties” in the enroll Panel”.
Communications Port Change: The installation program will automatically add the HSP Modem™ to Com Port 5. Since certain applications require Com Ports 1-4, the Com Port can be changed by following the procedure outlined below [. Click SP Modem” under contralto Panel” Co control Panel 4 & a Game (EERIER intent Controllers 3D % = Modems Sousa Multimedia Network 1 2 ® Power Priers Regional 2. Choose the appropriate Com Port and click apply. This will complete the Com Port change.
Installation: The HSP Modem™ can be uninstalled by using the following procedure. i. Click SP Modem” under control Panel”. OX & mE Game RRS Internet Keyboard Controllers D 9 # Mouse Multimedia Printers Regional System Settings BH 2. Click uninstall. The installation program will automatically remove the HSP Modem™ from the system.
HSP PCI Modem™ Setup using Windows NT Workstation 4.0 Windows NT 4.0 cannot automatically detect the CPU type fem different vendors; therefore, we have provided different drivers for the appropriate CPU type. Be sure to use the correct driver for your CPU type. [f you are unsure of the CPU type. contact your system vendor. Note: There are twa ways to install the PCI Modem under Windows NT 4.0. Both options are shown below.
Click on Restart Now”. The system will be restarted after installing the modem. [EC nd 5. The new Communications Port should be shown. Click lose” to continue.
8. Select 9, Make sure the driver disk is installed in the A: Drive and click ave Dial an detect my modem” and click Install New Coder 10. Click DAE Standard 300 bps Modem Standard 1200 bps Modem Standard 2400 bos Madam § Endmost 3500 bus Modem R Stoned 14400 bps Modem 3 Started 19200) vine Medan «7 ro continue the installation program 17 ext”. kK”.
12. Select the Communications Port added for the HSP Modem ™ and click ext”. complete the installation program, the new Communications Port needs to be ana EEE Click SP Port”. confirmed. Under control Panel”. select Phi) Accessibly Add/Remove Data Tie t Dog ions ~~ Programs .
K”. Restart 14. The new Com Port should be listed. Select the new Com Port and click the system. 15. After restarting the system, the following modem should be listed under dome Properties” in the control Panel”.
Option 2: 1. The second option te install the HSP Modem ™ is done in un" under the tart” menu. Type the path as shown below to start the installation and click K”. 2. Click ext” to continue the installation program.
4. Install the driver disk in the A: Drive and click K™ 6.
an] After restarting the sy Properties” in the Madams Properties stem, the following modem should be listed under cilantro Panel”.
Installation: The HSP Modem™ can be uninstalled by using the following procedure. § 1. Under intro} Pane!”, click SP Port”. B 8 Microsoft Mal Modems Past office. PC lad HEP Port CIA) ® & Sounds 2. Click uninstall. The installation program will automatically remove the HSP Modem™ from the system.
2.3 Windows NT 4.0 with Service Pack 3 NT 4.0 PnP Modem Installation Before installing the modem drivers, the PnP ISA Enabler driver for NT must to be installed. The driver library on the Windows NT 4.0 CD-ROM includes the PnP ISA Enabler driver, which handles the detection and installation of Plug and Play devices in Windows NT 4.0. Install the PnP ISA Enabler driver (PISA) according to the following steps.
Lhd Lad Dada Lun CONFIRMATION [0 pHE CARER GEEK CRG SNR This device comp of the FCC Rules Operation is 3 tot allowing two comedians: CL This devices mar not cause harmful intermittence, and (21 This device must Accede anv interference Tackled | including interlace that Way Cause undesired aeration. NOTE: This equipment has bean tagger and found to comply with tha limits for a Class B dropsical device. Pursuant to Part 15 of the FCC Rules.