USER G U I D E English Français Deutsch Español CIRCA 74 AMPLIFIER ®
C O N G R AT U L AT I O N S on your new Circa 74 ® Amplifier. With your Circa 74 Amplifier, getting a great-sounding amplified acoustic tone is as easy as plugging in your guitar. If you have any questions about your amplifier, please contact Taylor Guitars Customer Service at 1-800-943-6782 in North America or +31 (0) 20 667 6033 in Europe.
Avertissement de sécurité Ce symbole est destiné à rappeler à l'utilisateur qu'il existe une non – isolation "Tension dangereuse" dans l'enceinte du produit. Ce symbole vise à attirer l'attention de l'utilisateur sur les instructions importantes d'exploitation et d'entretien (réparation) contenues dans la documentation accompagnant l'appareil. Ne pas exposer l'équipement à des gouttes ou à des éclaboussures d'eau.
Avertissement de sécurité 1. Veuillez lire toutes les instructions de sécurité et d'utilisation avant d'utiliser ce produit. 2. Conserver toutes les instructions de sécurité et d'exploitation pour référence future. 3. Lisez et comprenez tous les avertissements énumérés dans les instructions d'utilisation. 4. Utilisez ce produit conformément à toutes les instructions d'utilisation. 5. Attention: pour réduire le risque de choc électrique, ne pas exposer l'équipement à la pluie ou à l'humidité.
SAFETY ADVISO RI ES This symbol is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. Do not expose the device to dripping or splashing. Objects filled with liquids, such as vases or beverage containers, should not be placed on the device.
SAFETY ADVISO RI ES 1. READ all safety and operating instructions before using this product. 2. KEEP all safety and operating instructions for future reference. 3. READ and understand all warnings listed in the operating instructions. 4. FOLLOW all operating instructions to use this product. 5. WARNING: To reduce the risk of electric shock, do not expose this apparatus to rain or moisture. This product should not be used near water, i.e., bathtub, sink, swimming pool, wet basement, etc. 6.
CO NTRO L PAN EL TO U R 11 9 10 12 13 1 1 11 9 10 12 13 2 6 7 5 4 3 8 INPUT A Combination of balanced/unbalanced. For mic or guitar. XLR male or 1/4" phone plug. 2 I NP UT B Specifically for guitar.1/4" phone plug. 3 P OWER INDICATOR Amber light when power is on. Power switch on back panel (Page 6). 4 B L UETOOTH BUTTO N Hold to enable Bluetooth connections. 5 B L UETOOTH INDICATO R Flashes blue when looking for connections. Solid blue when device connected.
BACK PAN EL TO U R 1 5 2 3 4 1 FUSE HOLDER To replace fuse refer to page 9 of this manual. 2 POW E R CABLE INL E T The amplifier uses a standard IEC 320-C13 cable (provided) to interface to the wall socket. In the event that the fuse in your amplifier becomes damaged, only replace it with the proper type indicated for your region’s voltage in the table below the inlet. 3 DIRECT OUT Balanced XLR Connector to appropriate PA connection.
BLUETOOTH INSTRUCTIONS -The only control on the amplifier that affects the Bluetooth Audio is the Master Volume, which also affects the volume level of the two physical XLR & 1/4-inch inputs. -You control the individual level of the Bluetooth Audio, with respect to the two physical amplifier input channels, using the volume controls on the Input Device.
TECHNICAL SPECIFICATIONS AC POWER 100 - 240 V AC ~ 50 / 60 Hz 11 5 V AC 6 0 H z All power measurements taken at 115 V AC 60 Hz Max Current Draw Nominal Current Draw Fuse Recommended Type Power Consumption (Idle) Power Consumption (Full Power) 1.97 A max (at full output power) 230 mA 250 V AC 2 A TL - Slow Blow Time Lag (5 mm X 20 mm) 12 W (No input signal, controls full C.C.W. position) 152 W (100 Hz Sine wave 30 mV, controls full C.W.
FUSE REPL ACEM ENT 1 Turn off power. 2 Unplug the power cable. 3 Unscrew fuse holder with flathead screwdriver. 4 Replace blown fuse with new T2L250V fuse. 5 Reinstall fuse holder. Keep a spare fuse ready for future use. If fuse continues to blow, contact an amplifier repair professional FCC STATEMENT Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
IC WARNING This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
