5000/5100 Reference Manual Version 1.02 Jun.
STATEMENTS Copyright © CipherLab Co., Ltd. 2004 All rights reserved. This document, as well as any software included, may not be reproduced, stored in retrieval system or transmitted, in any form or by any means, without prior written consent of the copyright owners. Trademark The logo is a registered trademark of CipherLab Co., Ltd. Disclaimer of Liability Efforts have been made to ensure the accuracy of the information presented in this document.
Statements: FCC Regulations & Technical Standards FCC Regulations: zThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. zThis device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
CONTENTS REVISION HISTORY .................................................... 錯誤! 尚未定義書籤。 PREFACE ................................................................................................... 1 CARE & MAINTENANCE .............................................................................. 2 GETTING READY ........................................................................................ 3 1. INTRODUCING 5000/5100 ....................................................................... 4 1.
Contents: Section 2 ~4.3 2. INSTALLING 5000/5100 ........................................................................ 24 2.1 Setting up the terminal ..................................................................................... 24 2.2 Wiring................................................................................................................ 29 2.2.1 Pin Assignments........................................................................................ 30 2.2.2 RS-232 .................
Contents: Section 4.4 ~ 4.4 Program Manager ............................................................................................ 60 4.4.1 Download .................................................................................................. 61 4.4.2 Activate...................................................................................................... 64 4.4.3 Version ...................................................................................................... 65 4.
Contents: Tables Table 1: Power consumption................................................................................ 9 Table 2: Memory explained ................................................................................ 11 Table 3: Keypad explained................................................................................. 13 Table 4: Display formats..................................................................................... 14 Table 5: Types of readers ..........................
Contents: Figures Figure 1: References for setting up system.......................................................... 3 Figure 2: Nomenclature of terminal ...................................................................... 5 Figure 3: Components inside terminal.................................................................. 6 Figure 4: Physical dimensions.............................................................................. 7 Figure 5: Installing battery pack .................................
Contents: Sample Screens Screen 1: Status lights as menu indicators ........................................................ 40 Screen 2: System Menu> 1. Information ............................................................ 44 Screen 3: System Menu> 2. Settings ................................................................. 45 Screen 4: System Menu> 2. Settings> 1. Clock ................................................. 45 Screen 5: System Menu> 2. Settings> 2. Backlight Period .......................
PREFACE The 5000/5100 stationary batch terminals are intended for versatile data collection applications with its large and expandable database capacity, and allow programmable solutions to meet varying needs of customers. Various operational parameters can be configured, such as backlight control, buzzer control, graphic screen and output format. Integrated with a proximity reader and backlit keypad, the 5000 terminal simply satisfies general needs regarding large data collection.
CARE & MAINTENANCE This is specifically prepared for those who are in charge of taking care of the terminals, such as a terminal operator or maintenance engineer. Here are some tips on how to take care and maintain the terminals. Taking care of the terminal z z z z z Always keep electric equipments like the terminals away from any flammable sources. Always make sure there is stable power supply for the terminal to operate properly. This terminal is intended for indoor use.
GETTING READY If you are using the terminal for the first time, the illustration below gives outline of the system and section references. Access to the configuration menus needs to disconnect the external and internal power connection of the terminal first. Therefore, we suggest that you do all the configuration and downloading jobs before setting up the system on site.
1. INTRODUCING 5000/5100 This section mainly explains the hardware construction and features of the 5000/5100 terminals. The 5100 terminal looks similar to the 5000 terminal except for the screen. 1.
Introducing 5000/5100: Nomenclature 1.
Introducing 5000/5100: Nomenclature 1.2.
Introducing 5000/5100: Nomenclature 1.2.2 Dimensions These drawings provide 3-sided views with dimensions, which are helpful in choosing a suitable location for installation.
Introducing 5000/5100: Features 1.3 Features 1.3.1 Power Line Power & Main Battery A 12 V/ 1000 mA wall adaptor is used to power the 5000/5100 terminals. Furthermore, an optional 7.4 V/ 2000 mAh Li-ion battery pack provides more than six extra hours of uninterrupted operations when the line power is down. Such power switching mechanism is actuated by a power switch, which seamlessly switches between the line power and the battery pack without any user’s intervention.
Introducing 5000/5100: Features Power Consumption Status The System Menu provides information on power consumption. z Monitor voltage level: Line / Main / Backup >> Also see Section 4.3.5 Power For the 5100 terminal, the smart battery icon will replace the plug icon on the screen when it is battery-operated. Here is another way to tell a low or discharged main battery from the screen.
Introducing 5000/5100: Features Installing Battery Pack If there is any need to replace the battery pack, follow the instructions described below. 1. Seat the battery pack into the battery compartment at the lower enclosure. 2. Connect the battery wires to the receptacle on the charger. To access the configuration menus, disconnect the battery wires and external line power.
Introducing 5000/5100: Features 1.3.2 CPU A 16-bit low power CMOS CPU is utilized. With little current consumed, yet, this CPU can run under 22.1184MHz and provide more than 6 MIPS of computation powers. 1.3.3 Memory & Calendar In the event of a power failure with no battery pack installed, the 7 mAh button cell on the main board is to keep contents of the SRAM and run the calendar for at least 1 week.
Introducing 5000/5100: Features Installing Memory Card 1. Align pinholes at the back of the card to the pins on the main PCB. 2. Press down the card flatly. Be careful not to bend or distort any pins. 3. Then apply the screw to screw down to the pole.
Introducing 5000/5100: Features 1.3.4 Keyboard A 21-key keypad is for system setup, user entry and so on. Figure 7: Keypad layout Silicon rubber has been chosen for their durability and prompt feedback. The key click can be configured through the System Menu. >> Also see Section 4.3.2 Settings These keys can be categorized into two groups: Function keys (F1~F6): - User-definable, each comes with a GREEN LED underneath. Can be used to show the current system status such as working shifts, etc.
Introducing 5000/5100: Features Optional External Keyboard The 5000/5100 terminals provide one keyboard port. You may connect an external keyboard to this port. 1. Connect wires from the keyboard module to the receptacle on the main PCB. 2. Connect the external keyboard to the PS/2 port. 1.3.5 LCD The 5100 terminal comes with a 128 by 64 pixels FSTN graphic LCD, which is able to display message in formats as follows: English fonts: Chinese fonts: Other language fonts, company logo, etc.
Introducing 5000/5100: Features 1.3.6 Status LEDs There are four indicators on the front panel for status feedback. They are programmable for diagnostics and application dependant. z z z z Red LED Green LED Yellow LED Orange LED – Power – Good Read – 485 Comm. – Host Comm. 1.3.7 Buzzer The buzzer is a low power transducer type, and its pitch and duration are software programmable. 1.3.8 Readers Two types of readers are supported: 125 KHz EM: From contact to 6 cm 13.
Introducing 5000/5100: Features 1.3.9 Digital Inputs There are totally 4 groups of digital inputs. Each is electrically isolated from the outside world by a photo-coupler. Current must flow through the internal LED to turn on the output transistor. A typical 1 mA turn-on current is recommended. A sample circuit is depicted below. Vext external power R 4 1 3 2 DIN+ DINexternal ground Figure 8: D/I sample circuit How to decide the R value? Premise: the LED forward voltage is about 1.15 V.
Introducing 5000/5100: Features 1.3.10 Digital Outputs There are totally 4 groups of digital outputs. Each is a relay that is able to sustain 1 A under 30 VDC or 0.3 A under 125 VAC. Both normal open (NO) and normal close (NC) contacts are provided to accommodate application needs. These relays are sufficient to provide direct control over normal house door electric lock, alarm and so on. External high power relays might be needed for turnstile, automatic doors and so on to satisfy “heavy loads”.
Introducing 5000/5100: Features 1.3.11 RS-232 A standard RS-232 port is available on the JP3. Unlike the “external reader port”, these signals are true RS-232C compliant. With proper cabling, shielding, wiring and so on, it is able to communicate to another device up to 50 feet (approx. 15 meters) away. This port is mainly used to communicate to the host computer, i.e. being a stand-alone unit or master terminal under multi-station systems. The final use, of course, is not limited.
Introducing 5000/5100: Features 1.3.12 RS-485 A standard RS-485 port is also available on the JP3 to constitute multi-station systems. Though it is simple and low cost, care must be taken to ensure proper operations. z z z z The data rate is 125 kbps. Compatible to CipherLAB 510, 520 and so on. Maximum network run length is 1000 meters No fork, nor star connections. As depicted below, connections b, d & f are acceptable but not others.
Introducing 5000/5100: Features The illustration below shows a typical topology of networking multiple terminals through RS-232 and RS-485 interfaces.
Introducing 5000/5100: Features 1.3.13 Ethernet An optional 10/100 Base-T Ethernet card can be attached to merge the terminals onto any existing legacy Ethernet networks. It comes with a standard RJ-45 connector and is fully standard compliant. Just like the RS-485, the IP address must be set accordingly.
Introducing 5000/5100: Features Installing Ethernet Card You may have to install the Ethernet card to the terminal by yourself. If you have installed a memory card, attach the Ethernet card on top of it then. 1. Align the pinholes at the back of the card to the pins on the main PCB. 2. Press down the card flatly. Be careful not to bend or distort any pins. 3. Then apply the screw to screw down to the pole. Figure 13: Installing Ethernet card 1.3.
Introducing 5000/5100: Unpacking & Options 1.4 Unpacking the package The following items are included in the package. Save the box and packaging material for future use when you need to store or ship the terminal. z The 5000 or 5100 Terminal z Power Adaptor z Software CD & Reference Manual (for authorized distributors only) 1.5 Options There are several optional accessories to enhance the total performance of the terminals.
2. INSTALLING 5000/5100 2.1 Setting up the terminal The whole installation can be simply classified into the following stages: Site Survey: Choose a location that is close to the target door and provides clearance for the cables and access to an AC outlet. Mounting: - Drill holes on the wall. Mount the lower enclosure on the wall. Attaching: Attach optional accessories to the PCB. Wiring & Connecting: - Connect wires to terminal blocks. Connect connectors to receptacles. Connect to Ethernet networks.
Installing 5000/5100: Setting up the terminal Figure 14: Drilling holes & assembling cables Drilling Holes & Assembling Cables 1. Make use of the mounting template provided in the appendix, and drill four holes in an appropriate location for installing the terminal: z Each hole shall be 6 mm in diameter and 21 mm in depth. z The four holes enclose a square of 120 mm x 120 mm. 2. Insert the four wall plugs (screw anchors for concrete surface) into the four holes.
Installing 5000/5100: Setting up the terminal Figure 15: Mounting to wall Mounting to the Wall 4. Make sure the cables are routing and arranged in the cable channel at the back. Such design is to keep cables invisible and inaccessible from the outside. 5. Apply four 4x16 screws to mount the lower enclosure on the wall. Attaching Optional Items 6. Attach the battery pack, memory card and Ethernet card, if there is any. >> Also see Sections 1.3 Features & 1.
Installing 5000/5100: Setting up the terminal Figure 16: Wiring & connecting Wiring & Connecting 7. Attach connectors of the keyboard module, reader module, charger or battery pack to receptacles on the PCB. 8. Follow the wiring instructions to insert every wire to a corresponding slot of the terminal blocks . Tighten screws to secure wires. Then plug the terminal block in to the PC board socket. z z z z Connect line power. Connect digital inputs and outputs.
Installing 5000/5100: Setting up the terminal Figure 17: Assembling enclosures Assembling Enclosures from Bottom to Top 10. Make sure there is no more need to do hardware configuration and/or downloading application program. At last, position the two tabs at the bottom of the upper enclosure into the notches at the bottom of the lower enclosure. The two pieces of enclosures snap to fit. 11. Apply two M2x6 screws to secure the upper enclosure to the lower enclosure on top. Connecting to Power 12.
Installing 5000/5100: Wiring 2.2 Wiring This section gives instructions on how to wire the terminal to external devices, a host, or another terminal. RS-232 (JP3) Connect to a host computer RS-485 (JP3) Connect to another terminal Digital inputs (JP3) Connect to external devices like an actuator (button) to open door Digital outputs (JP2) Connect to external devices like door lock, siren, etc.
Installing 5000/5100: Wiring 2.2.1 Pin Assignments The pin assignments are listed and described below. JP2: Pin No.
Installing 5000/5100: Wiring JP3: Pin No.
Installing 5000/5100: Wiring 2.2.2 RS-232 Without using additional devices like optical isolators or signal boosters, the cable length is limited to 50 feet (approx. 15 meters) to ensure communication quality according to IEEE standard. Instructions Make use of a 9-pin female connector (DB-9) at PC end, and wire pins as follows: Figure 19: RS-232 wiring Wiring materials: Use 22 ~ 24 AWG braided shielded cable.
Installing 5000/5100: Wiring 2.2.3 RS-485 Connections between every two terminals are set up through RS-485 interface. When more than two of the terminals are connected (as a multi-station system), a host only needs to connect to the first one terminal (master) and it can then communicate with the rest terminals (slave). On the last slave device, a termination resistor is usually essential. There is one terminator on the PCB of each terminal, and a DIP switch (s1) is beside JP3.
Installing 5000/5100: Wiring Instructions When settings are completed, you may proceed with physical connection between every two terminals. To set up RS-485 connection, the communications cable must be wired as shown below: Figure 21: RS-485 wiring Wiring materials: Please use 22 AWG braided shielded cable or Cat 5 UTP (Unshielded Twisted Pair) cable. The maximum cable length can be up to 1000 meters.
Installing 5000/5100: Wiring 2.2.4 Digital Inputs/Outputs DI/DO are four sets of separate signal on the terminals. DI via JP3 D/I type: A photo-coupler that can be used to monitor external devices. For example, a button can be used to activate and open a door. DI wiring allows four groups of signals and is done through JP3. DI Group No. Pin No. (+) Pin No. (–) Pin No. (+5V) Pin No.
3. SYSTEM ARCHITECTURE The whole system can be simplified as hardware and software at PC end and terminal end. The software inside the terminal mainly consists of three modules: Kernel, System, and Program. For system configurations and managing multiple programs, each terminal comes with System Menu, Kernel Menu, and Program Manager. Figure 22: System Architecture Program Manager Menu, which is generated by 51pm.shx, is unavailable by default. Please download 51pm.shx in the System Manu first.
System Architecture: Operation According to different purposes for which the modules serve, the software inside the terminal also can be viewed in the following way: Menus Purposes Setup Menu OR User-defined menu Setup Menu is generated by the proprietary 5100*.SHX program. The menu functions and access keys depend on the application program you download to the terminal. System Menu A portal to system configurations. Kernel Menu Generally, this is for manufacturing use only.
System Architecture: Download 3.2 Download The terminal must be configured correctly for downloading either of the following: z Program update z New application program z Font file (only RS-232 interface is allowed) Proprietary Application Programs (5100*.SHX): The following programs have been developed to meet varying application needs. One of them is preloaded inside the terminal. - Access Control: 5100AC-MS-V1.0.SHX Time & Attendance: 5100T&A-V1.0.SHX Shop Floor (Work-in-Process, WIP): 5100SF-V1.
System Architecture: Management 3.3 Management Install a management utility at PC end that corresponds to the current application. Then, proceed to define the environments for the terminal to work. Please see programming guide for details. The terminal must be loaded with an appropriate application first. Proprietary Management Software for 5100*.SHX: The software is in correspondence to proprietary application programs. - Several PC end utilities are available for remote management. For example, Menjin.
4. CONFIGURING 5000/5100 This section mainly describes the alternatives to configure the 5000/5100 terminals, including hardware configuration and downloading application programs. Although the 5000 terminal is not equipped with a screen, you may proceed with configurations by following the LED indicators and relevant sample screens of menus in this manual. Without a screen, some menus are not operational on the 5000 terminal. 4.
Configuring 5000/5100: Selecting from menus 4.2 Selecting from menus The function keys can also be used in selecting item from menus on the screen. z To select item 1 to 5 on any menu, simply press [F1] to [F5]. z To select item 6 on any menu, press [F6] then [F1]. z To select item 7 on any menu, press [F6] then [F2].
Configuring 5000/5100: Selecting from menus Figure 23: Function keys as menu indicators 42
Configuring 5000/5100: System Menu 4.3 System Menu The System Menu is generated by a powerful utility, which offers an interface for engineers (programmers or system integrator) to view system information, change the configuration parameters, manage files and run diagnostics. This menu is designed for engineering tests and maintenance ONLY. For this reason, the System Menu provides password protection to prevent unauthorized users from accidentally changing system settings.
Configuring 5000/5100: System Menu 4.3.1 Information Screen 2: System Menu> 1. Information The information provided here helps diagnose the system. z H/W: Hardware version (PCB) z S/N: Serial number of the terminal z M/D: Manufacturing date z KNL: Kernel version z LIB: C library version z USR: Application program version z DEV: Code for optional hardware configurations, i.e. 1700. See Kernel> Information for device code.
Configuring 5000/5100: System Menu 4.3.2 Settings Screen 3: System Menu> 2. Settings Here provides options to change the default settings. System settings Default values Clock N/A Backlight Period 20 seconds CPU Speed Full speed Key Click Tone 2 System Password Open access Font System font Table 18: Default system settings Settings > Clock Set date and time for Real Time Clock. Enter two digits for the year, i.e. 04 for 2004. Screen 4: System Menu> 2. Settings> 1.
Configuring 5000/5100: System Menu Settings > Backlight Period Set the backlight duration for the keypad and LCD. Enter a value between 0 and 99999. Screen 5: System Menu> 2. Settings> 2. Backlight Period Settings > CPU Speed Set the CPU speed to save power if necessary. The current value is highlighted. Options include: Full, Half, Quarter, Eighth and Sixteenth. Screen 6: System Menu> 2. Settings> 3.
Configuring 5000/5100: System Menu Settings > Key Click There is audible feedback for pressing a key on the keypad. The current value is highlighted. Select a tone for the buzzer or mute it. Screen 7: System Menu> 2. Settings> 4. Key Click Settings > System Password Set a password to control user access to the System Menu. The password consists of eight characters at most. To disable a previous password, enter blank on the following screens. Screen 8: System Menu> 2. Settings> 5.
Configuring 5000/5100: System Menu Settings > Font Current font information can be viewed here. z z Default: System font Custom font file, if there is one The font settings here can be changed if a multi-languages font file has been downloaded. (Press [2] / [8] to move down / up the menu of options.) Screen 9: System Menu> 2. Settings> 6. Font Without a screen, this is not available on the 5000 terminals.
Configuring 5000/5100: System Menu 4.3.3 Tests Screen 10: System Menu> 3. Tests Here provides functional tests for key parts: Tests > Memory Test the data memory (SRAM), and the results will be shown on the screen. Press any key to exit. Without a screen, this is not available on the 5000 terminals. Warning! The contents of the data memory (SRAM) will be wiped out after test. Tests > Buzzer Test the buzzer with different frequency/duration combinations. Press [Enter] to start.
Configuring 5000/5100: System Menu Tests > LCD & LED Test the LCD display and LED indicator. Press [Enter] to start. Press any key to stop and exit the test. You may only be able to test the LED indicators on the 5000 terminals. Tests > Keyboard Test the rubber keys. Press any key and its corresponding character will be shown on the screen. Press [ESC] to stop and exit the test. Without a screen, this is not available on the 5000 terminals.
Configuring 5000/5100: System Menu 4.3.4 Memory Screen 11: System Menu> 4. Memory Memory > Size information Here provides information regarding the data and program memory: z z z Base RAM Memory Card Flash (SRAM for data memory) (SRAM for data memory) (for program memory) Without a screen, this is not available on the 5000 terminals. Memory > Initialize Perform task initializing the data memory (Base RAM or Memory Card).
Configuring 5000/5100: System Menu 4.3.5 Power Screen 12: System Menu> 5. Power Here shows current voltage consumption for Line / Main / Backup. z Line: Line power (DC) status. z Main: Main battery status. The battery pack is a standby power source when line power is down. z Backup: Backup battery status. The button cell is used to retain data in SRAM and maintain RTC. Without a screen, this is not available on the 5000 terminals.
Configuring 5000/5100: System Menu 4.3.6 Load Program Screen 13: System Menu> 6. Load Program The terminal must be configured correctly for downloading either of the following: z Program update z New application program z Font file (only RS-232 interface is allowed) Interfaces: RS-232 Ethernet Default parameters are 115200, none, 8, 1. The communication parameters at PC end should be set accordingly.
Configuring 5000/5100: System Menu 4.3.7 NET Menu Screen 14: System Menu> 7. Net Menu This submenu is for IEEE 802.3 10/100Base-T Ethernet networking, and is available only when an Ethernet card is installed. Parameters must be configured correctly. The menu can only be shown when the 5kTCPIP.LIB is linked. Net Menu > Information Information of network configuration can be viewed here. z z z z z z LIB: MAC: DHCP: IP: Mask: Gate: Version of 5KTCPIP.
Configuring 5000/5100: System Menu Net Menu > IP Setting Set network parameters: z z z z z z z DHCP: SubNet Mask: Local IP Address: Default Gateway: DNS Server: Local Name: Domain Name: Options – Enable or Disable Enter a new Mask IP, if necessary. Enter a new address for the terminal, if necessary. Enter a new address for the default Gateway, if necessary. Enter a new address for the DNS server, if necessary. Enter a name for identifying the terminal. The domain name of the host is shown here.
Configuring 5000/5100: System Menu Screen 16: System Menu> 7. Net Menu> 2.
Configuring 5000/5100: System Menu Net Menu > Echo Tests Echo tests are used for verify connectivity. Press [ESC] to stop and exit the test. You also need a test utility on PC to test the networking. Screen 17: System Menu> 7. Net Menu> 3.
Configuring 5000/5100: System Menu z Client Mode: z Server Mode: Set the terminal as a server. Followed by an attempt to make connection with the access point. Set the terminal as a client. Enter the IP address of a server that connection is desired. Followed by an attempt to make connection with the access point. Screen 18: System Menu> 7. Net Menu> 3.
Configuring 5000/5100: System Menu Net Menu > Download via TCP/IP If an Ethernet card is installed, the terminal can download new application program or program update via TCP/IP. You also need a downloading utility on PC to download program through network. Results z Success: the new program will be activated right after downloading. z Failure: the terminal will resume to the current application program Screen 19: System Menu> 7. Net Menu> 4.
Configuring 5000/5100: Program Manager 4.4 Program Manager The 5000/5100 terminals support multiple applications and languages. In the menu of Program Manager, it can download up to seven programs and one of them is made active. Warning! The Program Manager menu is NOT for the use of any end users. How to access the Program Manager? 1. 2. 3. 4. 5. Lift the upper enclosure by unscrewing the two screws on top of the terminal. Disconnect BOTH the line power and main battery.
Configuring 5000/5100: Program Manager 4.4.1 Download Screen 20: Program Manager> 1. Download Multiple programs as well as custom font file can be downloaded through RS-232 interface. There is a full list of programs and font file that are currently stored in the terminal as follows.
Configuring 5000/5100: Program Manager Spare application programs Empty slot: 1. 2. 3. 4. Select an empty slot by pressing the corresponding number and then [Enter]. Select baud rate for downloading. Set matching parameters at PC end. Connect cable and wait connecting… To abort the action, press [ESC]. Then press [ESC] again to return to the menu. Occupied slot: If no available slots, you’ll have to replace one program with the new one. 1.
Configuring 5000/5100: Program Manager Active application program or font file The active slot: 1. Select the active program (may be an empty slot) by pressing the corresponding number (that is 7) and then [Enter]. 2. Set matching parameters at PC end: 115200, none, 8, 1 3. Connect cable and wait connecting… 4. If the downloaded program is an application, it will replace the active program and come into effect immediately. 5. If it is a font file, then the current active program is still in use.
Configuring 5000/5100: Program Manager 4.4.2 Activate Screen 21: Program Manager> 2. Activate The list shows the entire spare programs stored in the terminal. From the list, you can select from 01 to 06 and activate one of them. z When an application program is activated, it will be copied to the active memory and replace the old one. The screen instructs that “Press [ESC] to clear file”. It means the file system in the SRAM will be cleared out when pressing [ESC].
Configuring 5000/5100: Program Manager 4.4.3 Version Here provides information about the version of Program Manager. Without a screen, this is not available on the 5000 terminals.
Configuring 5000/5100: Kernel Menu 4.5 Kernel Menu The Kernel Menu resides in the innermost core of the system. It has the highest security and is always protected by the system. When the application program is corrupted and the System Menu fails, the Kernel Menu provides an access to fix the system. Warning! The Kernel Menu is NOT for the use of any end users. How to access the Kernel Menu? 1. Lift the upper enclosure by unscrewing the two screws on top of the terminal. 2.
Configuring 5000/5100: Kernel Menu 4.5.1 Information The information provided here helps diagnose the system. z z z z z H/W: S/N: M/D: KNL: DEV: Hardware version A unique serial number for the device Manufacturing date Kernel version Code for optional hardware configurations, i.e. 1700 1 7 Type of Reader Module Type of LAN Module 0= none 1= EM 2= Mifare 0= none 7= Ethernet 0 Reserved 0 Reserved Table 23: Device code explained Without a screen, this is not available on the 5000 terminals.
Configuring 5000/5100: Kernel Menu 4.5.2 Load Program The terminal must be configured correctly for downloading either of the following: z Program update z New application program z Font file 1. Connect RS-232 cable. 2. Set communication parameters at PC end: 115200, none, 8, 1. 3. Enter Kernel Menu> Load Program. The system is ready to download the program to the active slot. Only RS-232 interface is allowed. Results z Success: the new program or font file will be activated right after downloading.
Configuring 5000/5100: Kernel Menu 4.5.3 Kernel Update The Kernel might be changed for improving performance or other reasons, and an update is necessary. 1. Connect cable. 2. Set communication parameters at PC end: 115200, none, 8, 1. 3. Enter Kernel Menu> Kernel Update. The system is ready to update the Kernel firmware. Only RS-232 interface is allowed. 4.5.4 Test & Calibrate These tools are provided for manufacturing use. No user definition is allowed.
5. MANAGING 5000/5100 Depending on the application program downloaded to the terminals, managing the 5000/5100 terminals at PC end can be very flexible and simple. For details, please see relevant documents such as Programming Guide.
Managing 5000/5100 5.1 For proprietary applications For any preloaded application program (5100*.SHX), we provide several ways for managing the terminal from PC end. Management Utilities This is application dependant. For example, Menjin.exe is developed for Access Control application. Commands Sending commands serves as an alternative to manage the terminals. OCX Support Customized utilities can be developed in an efficient way. 5.
SPECIFICATIONS Power Line power: 12 V ± 5% DC at 1000 mA Main battery: Rechargeable 7.4 V, 2000 mAh Li-ion battery pack (optional) Backup battery: Rechargeable 3.
Specifications Enclosure Material & Color: ABS plastic Black Dimensions: 150 mm (L) x 150 mm (W) x 50 mm (H) Weight: Approx. 1.
TROUBLESHOOTING The terminal cannot accept valid cards… Regarding power – Check if the power adaptor is plugged into a wall outlet. Check if the outlet is working. If the problem persists, check if the wiring inside the terminal is correct and secured. Regarding memory – Check if memory buffer is full. Then clean buffer by downloading data to a computer. Regarding the reader – Check if the selected reader type in your application matches the default setting. >> Also see Section 4.3.
Troubleshooting The keyboard input seems not working properly… Test keyboard. >> Also see Section 4.3.3 Tests: Keyboard If the problem persists, re-connect the power and perform test. The external devices controlled by DI/DO signals are not working properly… Check if the device is properly wired to the terminal blocks. If the problem persists, re-connect the power and perform test. About abnormal response… The LEDs or LCD seem not working properly – Test components. >> Also see Section 4.3.
APPENDIX I – MOUNTING TEMPLATE This mounting template is provided in actual size (1:1 scale). 1. Place this paper on the place you desire to mount the terminal. 2. Use paper tape to attach it on the surface. 3. Then use a power drill to drill holes on the four corners. The size of these holes is 6mm in diameter and 21mm in depth. Make sure that your printout doesn’t zoom in/out during printing.
Installing WLAN card You may have to install the WLAN card to the terminal by yourself. If you have installed a memory card, attach the WLAN card on top of it then. Align the pinholes at the back of the card to the pins on the main PCB. Press down the card flatly. Be careful not to bend or distort any pins. Then apply the screw to screw down to the pole.
IEEE 802.11b When the 802.11b module is installed, the terminal can easily connect to legacy networks through access points (APs). Roaming among different networks is possible. IEEE 802.11b is an industrial standard for Wireless Local Area Networking (WLAN), which enables wireless communications over a long distance. The speed of connection between two wireless devices will vary with range and signal quality. To maintain a reliable connection, the 802.
Net Menu Re-connect the main battery and simultaneously press [5] + [7] + [9] from the keyboard. Press [7] into Net Manu This submenu is for IEEE 802.11b wireless networking. Parameters must be configured correctly. Note: This menu is available only when the 802.11b module is installed. 802.11b Menu: Settings: Default Values IP Setting DHCP Enable SubNet Mask 255.255.128.0 Local IP Address 0.0.0.0 Default Gateway 0.0.0.0 DNS Server 0.0.0.
¾ Net Menu > Information Information of network configuration can be viewed here. MAC: DHCP: DHCP being enabled or disabled IP: IP address of the terminal Mask: Subnet Mask Gate: Default Gateway MAC ID of the 802.11b module ¾ Net Menu > IP Setting Set general network parameters. DHCP: Options - Enable or Disable SubNet Mask: Enter a new Mask IP, if necessary. Local IP Address: Enter a new address for the terminal, if necessary.
The value you set must match that set for the access point. Power Saving: This refers to the low power consumption mode. Options - Enable or Disable The value you set must match that set for the access point. Preamble: Options - [1] Long [2] Short [3] Both The value you set must match that set for the access point. ¾ Net Menu > Security Set up or modify security parameters: Authentication [1] Open System: Default authentication type [0] Share Key: This requires implementing WEP key.
¾ Net Menu > Echo Tests Echo tests are used for verifying connectivity to make sure the terminal is within coverage. Client Mode: Set the terminal as a client. Enter the IP address of a server that connection is desired. It is followed by an attempt to make connection with APs. Server Mode: Set the terminal as a server. It is followed by an attempt to make connection with APs.
