Control Unit (used 4G/3G/GSM Communication) JRN-360T User Manual Document number: LE-20Y501-E Ver.1.01 Date: Mar. 31, 2022 JRC Mobility Inc.
History Date Mar. 18, 2022 Mar. 30, 2022 Number 1.00 1.01 The contents of change 7.2 Precautions for use 5. Change the description 10. Delete item 7.3 Notes on Equipment installation 1. Change the description 2,4 Delete item 7.5 Storage precautions 1. Change the description 7.
Table of contents 1 2 3 4 5 6 7 8 Introduction .................................................................... 4 Composition ..................................................................... 4 Function ........................................................................ 5 Product Specification ........................................................... 6 Outline ........................................................................ 10 Option ..................................................
1 Introduction This specification is an instruction manual for a 4G compatible communication terminal (JRN-360 T). JRN-360T is a small terminal for Construction equipment to have the GNSS measurement functi on and the 4G/3G/GSM communication function, and to use it for management and positional inf ormation track etc. of the Construction equipment. (JRN-360T is a device dedicated to specific cu stomers and will not be sold to the general public.) 1.
(Note#1) Please prepare IF cable by the visitor side. (Note#2) A connection I/F cable requires a 5A fuse because of over-current protection. Please insert the fuse in a battery. (Note#3) Please do not take a power supply from DC cigar socket. It becomes the cause that operation is poor, according to bad connection. 3 Function 3.1 Communication function with mail server. Receives the request by SMS and sends the result to the TFTP server. 3.
3.7 Monitor function The GNSS antenna connection status can be monitored by CAN communication. 3.8 LED indication LED indication is controlled the following conditions • When the key ON and coverage area, it blinks at a slow cycle (blinking cycle: 2 seconds). • When the key ON and no signal, it blinks with a fast cycle (blinking cycle: 0.5 seconds). • When the key OFF, LED light turns off (standby or sleep mode). 4 Product Specification 4.
3 GSM class Bd.4 (2100MHz) Bd.5 (850MHz) Bd.6 (850MHz) Bd.8 (900MHz) Bd.19 (850MHz) LTE: Bd.1 (2100MHz) Bd.2 (1900MHz) Bd.3 (1800MHz) Bd.4 (2100MHz) Bd.5 (850MHz) Bd.7 (2600MHz) Bd.8 (900MHz) Bd.12 (700MHz) Bd.13 (700MHz) Bd.18 (850MHz) Bd.19 (850MHz) Bd.20 (800MHz) Bd.26 (850MHz) Bd.28 (700MHz) Bd.66(2100MHz) Bd.38 (2600MHz) Bd.40 (2300MHz) Bd.
Class 3 (+23dBm ±2dB) for LTE 800, LTE FDD Bd20 Class 3 (+23dBm ±2dB) for LTE 850, LTE FDD Bd5 Class 3 (+23dBm ±2dB) for LTE 900, LTE FDD Bd8 Class 3 (+23dBm ±2dB) for LTE 1800, LTE FDD Bd3 Class 3 (+23dBm ±2dB) for LTE 1900, LTE FDD Bd2 Class 3 (+23dBm ±2dB) for LTE 1900, LTE FDD Bd25 Class 3 (+23dBm ±2dB) for LTE 2100, LTE FDD Bd1 Class 3 (+23dBm ±2dB) for LTE 2100, LTE FDD Bd4 Class 3 (+23dBm ±2dB) for LTE 2100, LTE FDD Bd66 Class 3 (+23dBm ±2dB) for LTE 2600, LTE FDD Bd7 Class 3 (+23dBm ±2dB) for LTE 23
• Uplink coding schemes – CS 1-4, MCS 1-9 • SRB loopback and test mode B • 8-bit, 11-bit RACH • 1 phase/2 phase access procedures • Link adaptation and IR • NACC, extended UL TBF Protocol: NMEA 15 Modes: Standalone GNSS (GPS, GLONASS, Beidou, Galileo) GNSS Features General: Automatic power saving modes. DC feed bridge and control of power supply for active antenna By PLS63-W 4G/3G/GSM communication module specification. 4.
4.5.1 Power control I/F Connector Pin No. Terminal name Remarks 1 BATT Main battery (8〜16V) 2 GND GND 3 KEY-ON signal ACC signal CAN RATE CAN rate setting 4 GND:500kbps Open:250kbps 5 CAN-H CAN Low-Level Voltage I/O 6 CAN-L CAN High-Level Voltage I/O 4.5.2 NO.
6 Option 6.1 GNSS Antenna 6.1.1 Specification NO． Items Specification performance 1 Antenna model DAS1595 2 Power supply voltage 3.0V to 5.0V 3 Consumption current 9mA±3mA (at 3.0V) 4 Cable RG174 5 6 Temperature range of operation Storage temperature range -40℃ to +85℃ -40℃ to +100℃ Received frequency GPS:1575.42MHz±3 MHz range GLONASS:1602MHz ±8 MHz 8 Polarized wave Right-handed circular polarization 9 LNA Gain 26±3dB 10 Output impedance 50 ohms 11 OUTPUT VSWR 2.
6.1.
6.2 6.2.1 Communication antenna (Built-in antenna) Specification No. Items Specification performance 1 Model CAU-7360TA 2 Antenna type Chip antenna + Pattern antenna 3 Environmental Regulation 4 Frequency Compliant with RoHS 699 − 960 MHz 1710 − 2170 MHz 2500 − 2690 MHz 5 Peak gain 699 − 960 MHz : 1.5dBi 1710 − 2170 MHz : 2.3dBi 2500 − 2690 MHz : 2.6dBi It is measured in free space.
7 7.1 Handling precautions About specification value Be sure to observe the specification value of this product. Using beyond the specification value may cause a malfunction. 1 Power supply voltage: Main unit (input voltage) This is the maximum voltage that can be applied between the power supp ly terminal and the ground terminal (GND). If this voltage is exceeded, a f ailure may occur.
6 Do not use the product for medical equipment, medical equipment that re quires a high degree of safety that affects human life, Space / aviation e quipment, Disaster prevention / crime prevention equipment and other equ ivalent equipment. 7 Do not use the product near people wearing medical electrical equipment. There is a risk of medical equipment malfunction due to the influence of radio waves. 8 Depending on the vehicle model, it may affect on-vehicle electronic device s.
7.4 Overcurrent protection 1 This product does not have a built-in fuse for overcurrent protection. To p revent danger, use an overcurrent protection fuse on the power line. 7.5 Storage precautions 1 Avoid locations that generate a lot of corrosive gas such as salt wind, chl orine, hydrogen sulfide, sulfur oxide, hydrogen chloride, and subsulfide gas. 2 Condensation will occur in places with rapid temperature and humidity cha nges.
Ban This symbol indicates a general prohibition notice not specified. Disassembly ban This symbol indicates a prohibition notice when disassembling this produ ct may cause an electric shock or other trouble. No touch This symbol indicates a prohibition notice when injury may occur by touc hing a specific part of this product under specific conditions.
8 Compliance with FCC and IC Rules and Regulations ・FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
