BARCOPROJECTION CINE VERSUM SYSTEM R9001870 R9005010 R9841020 OWNER’S 17012003 MANUAL R5976490/01
Barco nv Home Cinema Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.84.30 Fax: +32 56.36.88.62 E-mail: salesassistantht.bci@barco.com Visit us at the web: www.homecinema.barco.
Copyright © All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of BARCO. Changes Barco provides this manual “as is” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose.
Table of contents TABLE OF CONTENTS 1. SAFETY INSTRUCTIONS. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3 1.1 General Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Module Related Safety Instructions . . . . . . . . . . . . .
Table of contents 2 R5976490 CINE VERSUM SYSTEM 17012003
1. SAFETY INSTRUCTIONS 1. SAFETY INSTRUCTIONS Overview • General Safety Instructions • Module Related Safety Instructions This manual is intended for the user/operator of the installed digital video distribution system.
1. SAFETY INSTRUCTIONS Protection from Ultraviolet Radiation WARNING: DO NOT LOOK DIRECTLY IN THE HIGH INTENSITY LIGHT BEAM. The lamp contained in this product is an intense source of light and heat. One component of the light emitted from the lamp is ultraviolet light. 1.2.2 Cine VERSUM 50 Lightning conditions In extremely bright surroundings, adjusting the screen intensity may not result in perceptibly brightener images. Keep in mind that extreme intensity settings can reduce system service life.
2. SYSTEM CONFIGURATION 2. SYSTEM CONFIGURATION Overview • The Video Distribution Solution • Overview of the System 2.1 The Video Distribution Solution The Cine VERSUM Revolution Thank you for purchasing the Cine VERSUM system from Barco. You are now at the gates of projection heaven. The Cine VERSUM from BARCO Home Theatre is the result of a completely new look at home theater.
2.
3. OVERVIEW USER’s CONTROLS 3. OVERVIEW USER’S CONTROLS Overview • Cine VERSUM Master • Cine VERSUM 80 • Cine VERSUM 50 • Remote Control • Remote Control operation 3.1 Cine VERSUM Master Front View The front side of theCine VERSUM Master is provided with the following controls: Image 3-1 Front side Cine VERSUM Master Controls function description Ref. Function Description 1 Infra Red Reception LED indicator Lights up when a valid Infra Red signal from the Remote Control has been captured.
3. OVERVIEW USER’s CONTROLS Image 3-2 Cine VERSUM 80 controls Controls function description Ref. Function Description 1 Infra Red Receiver Reception diode for the IR signals from the Remote Control. Allows switching On/Off (Standby) of the projector separately and controlling the Cine VERSUM Master. 2 Infra Red Reception LED indicator Lights up when a valid IR signal from the Remote Control has been captured. 3 Standby LED Lights up continuously: projector in the operation mode.
3. OVERVIEW USER’s CONTROLS Image 3-3 Cine VERSUM 50 controls Controls function description Ref. Function Description 1 Main Power Switch Switches the Cine VERSUM 50 in the Standby mode. Operation mode is controlled by the Cine VERSUM Master. 2 Infra Red Receiver Reception diode for the IR signals from the Remote Control to control the Cine VERSUM Master. 3 Standby LED Indicates the status of the Cine VERSUM 50, lights up in standby and operation mode. Table 3-3 3.
3. OVERVIEW USER’s CONTROLS Image 3-4 Remote Control Controls function description Ref. Function Description 1 Address button To match the Remote Control with the unit that you are addressing (number between 0 and 9). 2 Standby button To power up/down the Cine VERSUM Master and the displays in the link. 3 Digit buttons Allows to directly select sources.
3. OVERVIEW USER’s CONTROLS Digit Button Stored source 4 5 6 7 8 3.5 Remote Control operation Overview • 3.5.1 General • Battery Insertion in the Remote Control • Visualization of commands General How to use The Remote Control allows you to control your Cine VERSUM Master, even when it is built into a cabinet. Indeed, the SL/XL cable allows for 2–way communication. This means you can point the Remote Control to a display unit and still change the settings of the Cine VERSUM Master.
3. OVERVIEW USER’s CONTROLS Factory address setting of the modules The factory address setting of the modules is as follows: Module Individual Address Common Address Cine VERSUM 80 address <9> no common address Cine VERSUM 50 address <9> no common address Cine VERSUM Master address <1> common address <0> Common address: is a fixed address, stored in the module. The module will execute the commands sent by a Remote Control, programmed with the common address <0>. 3.5.
3. OVERVIEW USER’s CONTROLS How to reinstall the address By removing the batteries, the address in the Remote Control will be set to 0. In case the different modules are controlled separately (own address), the respective address of the module you desire to control has to be set. To reinstall an address, follow procedure below: 1. Point the Remote Control to the module of which you want to know the address and press the address button (use a pencil).
3.
4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM 4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM Overview • Brief introduction • Upon first startup • Switching the system between OPERATION and STANDBY • Switching the system between STANDBY and ECONOMIC Standby • Switching the system OFF completely and BACK to Operation mode • Turning ON the system from total OFF mode 4.
4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM Image 4-3 Cine VERSUM Master jog dial Image 4-2 Cine VERSUM 80 Image 4-4 Power up selection 4.3 Switching the system between OPERATION and STANDBY Overview 4.3.1 • From OPERATION mode to STANDBY mode • From STANDBY mode to OPERATION mode From OPERATION mode to STANDBY mode Using the Jog dial on the Cine VERSUM Master 1. Press the jog dial once to enter the main menu. (image 4-5) 2. Rotate the jog dial until “Shut down” in the menu is pointed to.
4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM Using the Remote Control 1. Point the Remote Control to the front of the Cine VERSUM Master or to the Cine VERSUM 80. 2. Press the standby button . (image 4-9) The Cine VERSUM Master and the Cine VERSUM 80 go from OPERATION to STANDBY. Image 4-9 4.3.2 From STANDBY mode to OPERATION mode Using the Jog dial on the Cine VERSUM Master 1. Rotate the jog dial until “Power up” in the menu on the Cine VERSUM Master is pointed. 2.
4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM Image 4-12 Economic standby Using the Remote Control 1. Point the Remote Control to the front of the Cine VERSUM Master or to the Cine VERSUM 80 2. Toggle with the ↑ or ↓ arrow keys until “Economic” in the menu on the Cine VERSUM Master is pointed to (image 4-11). 3. Press ENTER to activate selection. The Cine VERSUM Master and the Cine VERSUM 80 go from STANDBY to Economic STANDBY.
4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM 4.6 Turning ON the system from total OFF mode How to turn ON the system back to Operation mode 1. Press the power switch on the Cine VERSUM Master (image 4-1). The Cine VERSUM Master goes from OFF to standby. (image 4-15) 2. Press the power switch on the Cine VERSUM 80 (image 4-2). The Cine VERSUM 80 goes from OFF to standby. 3. Turning on to operation mode, see From STANDBY mode to OPERATION mode, page 17.
4.
5. Direct source selection 5. DIRECT SOURCE SELECTION 5.1 From standby mode Using the digit buttons on the Remote Control 1. Make sure that the connected sources to the Cine VERSUM Master are turned on. 2. Using the digit button on the Remote Control, key in the corresponding slot number (from 1 to 8). (image 5-1) The Cine VERSUM Master powers up and starts on its turn powering up the connected displays. Image of the selected source appears on the display.
5. Direct source selection 5.2 Return to standby mode How to return to standby remotely 1. Point the Remote Control to the front of the Cine VERSUM Master or the Cine VERSUM 80. 2. Press the standby button on the Remote Control again. (image 5-2) The Cine VERSUM Master switches to the standby mode and switches on its turn the connected display into the standby mode. When switching the Cine VERSUM 80 into the standby mode, a cool down period for the lamp of about 1 minute is activated.
6. IMAGE CONTROL 6. IMAGE CONTROL Image controls The Brightness, Contrast, Sharpness (Detail), Color and Tint functions are directly accessible with the Remote Control. The adjustment functions, when selected, display a slide bar overlayed on the source image. It is useful to adjust the Brightness, whenever the ambient room lightning changes. The same is true for Contrast. Please note that for the best result, it is advised to first change the Brightness, then the Contrast. 6.
6. IMAGE CONTROL Image 6-4 Image 6-3 6.3 Sharpness (Detail) Control How to adjust the Sharpness The Sharpness function is used to adjust the image sharpness of video signals when using a video decoder installed in the Cine VERSUM Master. To adjust the Sharpness, press the (+) or (-) side of the button ’SHARP’ (image 6-5). The following barscale is overlayed on the source image,image 6-6. Press the (+) or (-) button until the sharpest display is attained.
6. IMAGE CONTROL 6.4 Color (Saturation) Control How to adjust the Color (Saturation) The Color function is used to adjust color saturation levels and is only active for Video and S-Video sources. To adjust Color, press the (+) or (-) side of the button ’COLOR’ (image 6-7). The following barscale is overlayed on the source image, image 6-8. Press the (+) or (-) button until the desired color saturation level is displayed. If color is set to a 0% level, the result will be black and white picture.
6.
Index INDEX C Cine VERSUM 5 System configuration 5 Cine VERSUM System 15 Switching On/Off the system Operation 11 Visualization of commands Return 22 To standby 22 13 15 S F First startup 15 I Image control 23–25 Brightness 23 Color (Saturation) 25 Contrast 23 Sharpness 24 Tint 25 Introduction 15 On/Off 15 L Location of User controls 9 Location of User’s controls 7–8 Cine VERSUM 50 8 Cine VERSUM 80 7 Cine VERSUM Master 7 O On/Off 15 Introduction 15 R Remote control 11–13 Battery insertion 12 Gene