Changes CineVERSUM provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. CineVERSUM may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice. This publication could contain technical inaccuracies or typographical errors.
TABLE OF CONTENTS 1.0 INTRODUCTION ............................................................................................................ 5 1.1 1.2 1.3 2.0 FEATURE HIGHLIGHTS .............................................................................................. 7 2.1 2.2 2.3 2.4 3.0 Motorized Focus and Zoom ............................................................................................................... 7 Using the internal green X-hatch pattern ..........................
R599760 - BlackWing Three User Manual
1.0 INTRODUCTION 1.0 INTRODUCTION 1.1 Upgrades and Changes The BlackWing Three features the latest innovations on the projector market: • The two HDMI inputs version 1.3. • The BlackWing Three complies with “HD-Ready 1080p” standard. • The new Optical Lens features a motorized zoom and focus for easier install. • The Light Engine has been re-designed to achieve an improved contrast. • The Color-Select filters have been improved to obtain a wider color spectrum reproduction.
1.0 INTRODUCTION 1.3 Quick Start Plug your video source into the BlackWing Three Connect your video source to the BlackWing Three using one of the available inputs: • HDMI 1 (version 1.3 with HDCP, supports digital SD, HD and PC formats) • HDMI 2 (version 1.
2.0 FEATURE HIGHLIGHTS pressing the button again. To prevent the lamp lifetime to get shortened, the projector cannot be switched OFF right after the lamp warm-up. This is normal, wait 60 seconds until you can switch OFF the projector. Never unplug the projector when it is switched ON, it may damage the lamp. 2.0 FEATURE HIGHLIGHTS 2.
2.0 FEATURE HIGHLIGHTS Custom (Gamma Setup) Custom Gamma Setup allows a fine adjustment of the projector gamma setup. The Custom sub-menu gives access to: • Correction Value from 1.8 up to 2.6 • Gamma Adjust Sub-Menu: advanced gamma curve setting. • Save: save the adjusted gamma curve parameters into memory. • Load: load a curve from memory. • All Reset: reset the gamma curve parameters to default settings and apply the Correction Value [1.8 - 2.6].
2.0 FEATURE HIGHLIGHTS 2.3 Setup Menu Image Profile The Image Profiles stores the following parameters: • Contrast • Brightness • Color • Sharpness • DNR • Color Temperature • Gamma setting • Offset Use the predefined Profiles: Cinema, Natural or Dynamic or configure your own Image Profile and save it to one of the 3 available User Profiles. Profile Memory Manage your Image Profiles.
2.0 FEATURE HIGHLIGHTS Aspect (available with SD signals) Aspect Ratio: changes the aspect ratio of the picture to the screen. Select the Aspect Ratio to your convenience, depending on the format of the signal.
2.0 FEATURE HIGHLIGHTS Resize (available with PC-compatible signals) The PC-compatible supported formats are: PC format Resolution fH fV pixel clock VGA@60Hz (1) VGA@60Hz (2) SVGA@60Hz XGA@60Hz SXGA@60Hz 640x480 640x480 800x600 1024x768 1280x1024 31.500 kHz 31.469 kHz 37.879 kHz 48.363 kHz 63.981 kHz 60.000 Hz 59.940 Hz 60.317 Hz 60.004 Hz 60.020 Hz 25.200 MHz 25.175 MHz 40.000 MHz 65.000 Mhz 108.
3.0 INSTALLATION GUIDELINES 3.0 INSTALLATION GUIDELINES 3.1 Projection Distance • 3.
3.0 INSTALLATION GUIDELINES 3.4 Operating LEDs WARNING (red LED) LAMP (orange LED) STANDBY/ON (red / green LED) LED Status WARNING Description RED An error occurs and prevents the projector to be switched ON. ORANGE Lamp time exceeds 1900 hours, replace the lamp before 2000 hours. ORANGE Blinking An error occurs during projection or the lamp cover is not firmly closed RED The projector is in STANDBY Mode. RED Blinking The projector is in Cooling down Mode, wait until the fans stop.
3.0 INSTALLATION GUIDELINES 3.6 RS-232C Protocol Pin Assignment 1 5 6 Pin No. Signal Name Pin No. Signal Name 1 N/C 6 N/C 2 RD 7 N/C 3 TD 8 N/C 4 N/C 9 N/C 5 GND 9 External Control Control of this unit is possible via a computer by connecting this unit to an automation device or computer with a RS-232C cross cable (D-sub 9 pins). The commands to control this unit and the response data format against the received commands are explained here.
3.0 INSTALLATION GUIDELINES Command Format When sending a command to this unit, use the following data format: Header Proj. ID Command 1 byte 2 bytes 2 bytes Header [ Com. Parameters Variable length: 0, 1 or 4 bytes ] LF 1 byte : Designates the Command type. 2 possible headers: ! (21h): Assigns command to the projector (Command) ? (3Fh): Query data from the projector (Asking command) Proj. ID : Designates the Projector Identification. Fixed to 89h 01h. Command : Designates command. Com.
3.0 INSTALLATION GUIDELINES Test Pattern 54h 53h 30h 36h 37h 38h 39h ASCII IR codes (xxh xxh xxh xxh) Emulate RCU 52h 43h Focus + 52h 43h 37h 33h 33h 31h Focus Zoom T 52h 43h 52h 43h 37h 33h 33h 32h 37h 33h 33h 35h Zoom W 52h 43h 37h 33h 33h 37h Do not display Display Grey Staircase Display Red Staircase Display Green Staircase Display Blue Staircase The command sent is executed as a Remote Control Unit command.
3.0 INSTALLATION GUIDELINES Brightness (-) Color (+) Color (-) Sharp (+) Sharp (-) 37h 33h 37h 42h 37h 33h 37h 43h 37h 33h 37h 44h 37h 33h 37h 45h 37h 33h 37h 46h Example: To emulate Brightness (+), send the command: 21h 89h 01h 52h 43h 37h 33h 37h 41h 0Ah c) Examples You want to... Check the connection between the projector and the computer Switch the projector ON Switch the projector OFF Switch the projector OFF with OSD confirmation (Emulate RCU) Change Active Input to Comp.
4.0 MENU STRUCTURE 4.0 MENU STRUCTURE MAIN MENU SUBMENU AVAILABLE OPTIONS Image Image Adjust Contrast -50 +50 Brightness -30 +30 Color -50 +50 Tint (for NTSC sources) -30 +30 Sharpness -30 +30 DNR (Digital Noise Reduction Color Temp.
4.0 MENU STRUCTURE Setup Source Image Profile Parameters: Contrast / Brightness Color / Sharpness DNR / ColorTemp Gamma / Offset Cinema Natural Dynamic User1 User2 User3 Profile Memory Save Save Save Clear Clear Clear Reset Reset Reset Picture Position Adjust the horizontal and vertical position of the picture on the screen HDMI Input Level (Available for HDMI1 and 2 inputs) Standard Enhanced Mask (for High Definition picture) OFF, 2.5%, 5% Overscan (for Standard Definition picture) OFF ON (2.
4.0 MENU STRUCTURE Install Func. Info. Menu Position Upper Left Upper Center Upper Right Left Center Center Right Center Lower Left Lower Center Lower Right Menu Display 15 sec. On Line Display (Display the active input when switching input) 5 sec. Off Flip H. (for rear projection) On Off Flip V.
5.0 MISCELLANEOUS 5.0 MISCELLANEOUS 5.1 Specifications Overview The BlackWing Three uses the latest technology developed for professional projectors.
5.0 MISCELLANEOUS 5.2 Dimensions 6.9’’ 585 mm 505 mm 23.0’’ 19.9’’ 19.9’’ 505 mm 175 mm 585 mm 23.
Contact Information: TEC - CineVERSUM 7, rue La CAILLE, 75017 Paris - FRANCE e-mail : info@cineversum.com, Web: www.cineversum.