Changes Cineversum provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Cineversum may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice. This publication could contain technical inaccuracies or typographical errors.
TABLE OF CONTENTS 1.0 SAFETY INSTRUCTIONS ............................................................................................. 5 1.1 1.2 1.3 2.0 INSTALLATION GUIDELINES .................................................................................... 8 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 3.0 How to select an Input or a Channel................................................................................................ 45 Channel Setup Menu..................................
9.1 9.2 9.3 9.4 10.0 MAINTENANCE............................................................................................................ 82 10.1 10.2 10.3 10.4 11.0 4 GPIO Port ........................................................................................................................................ 96 Configuring the GPIO...................................................................................................................... 96 Appendix: Projection Distances ............
1.0 SAFETY INSTRUCTIONS 1.0 SAFETY INSTRUCTIONS 1.1 Important information Lead-free regulation This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: http:// www.eiae.org.
1.0 SAFETY INSTRUCTIONS opening or removing covers may expose you to dangerous voltages and other hazards. Refer all service to qualified service personnel. temperature, as this causes condensation, which may result in fire, electric shock, or other hazards. • Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product.
1.0 SAFETY INSTRUCTIONS it. Fragments from a broken light-source lamp may cause injuries. • The light-source lamp used in this projector is a high pressure mercury lamp. Be careful when disposing of the light source lamp. If anything is unclear, please consult your dealer. • Do not ceiling-mount the projector to a place which tends to vibrate; otherwise, the attaching fixture of the projector could be broken by the vibration, possibly causing it to fall or overturn, which could lead to personal injury.
2.0 INSTALLATION GUIDELINES 2.0 INSTALLATION GUIDELINES 2.1 Packaging Ensure the following components were received with the projector: • FORCE 3D, Full-HD Projector with Built-In Keypad and LCD display • IR remote keypad (includes two 1.5V AA batteries and XLR to mini-stereo cable conversion to wired • Power line cord • Lens Mount Security Screw (M6x10mm, Qty. 2) 2.
2.0 INSTALLATION GUIDELINES 2.3 Lens Installation Installing a projection lens The projection lens, shipped separately from the projector, must be installed prior to setting up the projector. Remove the lens plug from the lens opening in the projector before installing the lens. Retain the lens plug for projector transportation to protect the projector’s optical components from dust and debris. The lens seals the projector, preventing contaminants from entering the interior of the projector.
2.0 INSTALLATION GUIDELINES NOTE: Voltage and current requirements are listed on the license label, located at the back of the projector. IMPORTANT Connect the projector's line cord to the AC receptacle at the AC inlet of the projector, then push the wire clip over the plug to retain it. This prevents the line cord from inadvertent disconnection. Plug the 3-pronged plug end into a suitably rated grounded AC receptacle. Switch the projector ON. The switch is located just above the AC receptacle.
2.0 INSTALLATION GUIDELINES 4) S-Video using two BNC cables, with Luma (Y) connected to 4 (Sy) and Chroma (C) connected to 6 (Sc). 2.7 Projector Distance, Offset Setting and Mounting Throw Distance Throw distance is the distance measured from your projector’s front feet to the screen. This calculation determines if there is enough room to install your projector with a desired screen size To estimate the throw distance take the horizontal width of the screen and multiply it by the lens throw ratio.
2.0 INSTALLATION GUIDELINES 21% x Base Screen Height 60% x Height Base Screen (B) Maximum vertical and horizontal offsets Note: These values depend of the projection lens used. Refer to chart below or ask your dealer for more information. The horizontal position of the image can also be offset. The image is moved to the left or right of optical center. The amount of horizontal offset available depends on the lens installed and if the image has already been vertically offset.
2.0 INSTALLATION GUIDELINES Precautions for Ceiling-mount • To ceiling-mount this unit, special expertise and techniques are necessary. Be sure to ask your dealer or specialist to perform mounting. • Do not mount at places that may be subjected to vibration and shock. • Depth of the screw holes (A) is 15 mm. Do not use longer screws as you may damage inside the projector. • Install at a safe place in case this unit or a part of it may drop.
2.0 INSTALLATION GUIDELINES adjustment color and focus adjustment color in the center of its range. Focus Setting focus using Remote Keypad. Zoom ZOOM Setting Zoom using Remote Keypad. 3) If necessary, center the image on the screen: If the projector is mounted off center to the screen axis, then offset the lens as much as required. Aim the projector over slightly towards the center of the screen, but use caution when doing so, as too much tilt will cause excessive keystone distortion.
2.0 INSTALLATION GUIDELINES 2.11 Advanced Optical Alignment Boresight Alignment Procedure 1) Display the Boresight Test Pattern by pressing the TEST key on the remote keypad or use the built-in keypad and press the soft key that displays Test on the LCD display, then UP ARROW KEY to cycle to Boresight, then Enter, to obtain the Boresight pattern below. Pattern I Pattern II Pattern III Boresight pattern. 2) Focus the image on cross-hair pattern I. Evaluate the focus on cross-hair image II and III.
2.0 INSTALLATION GUIDELINES or if the lens will not focus over the correct range of throw distances, then the boresight requires coarse adjustment, go to step 8. 8) The original factory boresight can be recovered approximately by positioning the 3 setscrews. Position the setscrews flush with the front face of the lens mount plate and in contact with the inner lens mount plate. This may require adjusting both setscrews and capscrews. 9) If further action is required. Repeat step 2.
3.0 GETTING STARTED 3.0 GETTING STARTED 3.1 General View Projection lens LEDs Rear IR sencor Lamp doors Built-in Keypad with LCD screen Input panel Slots AC receptacle Cooling air vents Adjustable foot Rear Side view • Built-in Keypad The built-in keypad is located on the side of the projector. Use it similarly to the IR remote to control the projector. An LCD display is located above the keypad for displaying projector status.
3.0 GETTING STARTED • Adjustable feet Located on the underside of the projector are three adjustable feet. Raise or lower these feet when positioning the projector to ensure it is level on all sides so the displayed image will appear rectangular without any keystone.Refer to “Adjusting Projector Height/Tilt”, page 13 instructions on how to adjust the projector’s feet.
3.0 GETTING STARTED Serial Port Connections RS-232 and RS-422, serial ports available on the projector: You can connect a device with a serial interface, such as a computer to either of these connectors (not both) and control the projector remotely by entering specific serial communication commands. Connecting RS-232 Two nine-pin D-sub connectors, labeled RS-232 IN and RS-232 OUT on the input panel, are dedicated to serial communication, see figure below.
3.0 GETTING STARTED Connecting Ethernet Ethernet Hub Connecting this unit via the Ethernet connector. The default IP address is 192.168.1.89 System Integration - GPIO Connector The GPIO connector on the input panel interface, provides a method of interfacing a wide range of external I/O devices. Refer to “Appendix: GPIO”, page 96 Connector for complete details on pin configuration and how to program the GPIO. 1 2 3 4 5 6 7 8 9 GPIO: General Purpose Input and Output connector.
3.0 GETTING STARTED the chain, so that only the last projector has one unused port RS-232 OUT, see Figure 2-22 Mixed Network. RS-422 RS-232 RS-232 Proj1 Computer Proj2 Proj3 Mixed Network Communication parameters, such as baud rate, must be set to match the particular controlling device, before connecting as a network—refer to the documentation that came with your controlling device to determine the proper baud rate. See Section 3 Operation for help changing the projector baud rate.
3.0 GETTING STARTED To isolate just Ethernet communications, select “RS-232 and RS-422 Joined”—only projector #1 will respond via Ethernet. 3.4 Projector Communications Status LEDs Looking from the back of the projector, the LEDs represent, from left to right Lamp 1, Lamp 2, Power and Shutter.
3.
4.0 CONNECTING SOURCES 4.0 CONNECTING SOURCES 4.1 Connecting a device to the projector Connect your source to an Input board inserted into one of the available input slots located at the rear of the projector. Sources are connected to the Input Panel located at the back of the projector. The Input Panel allows one image processor board and up to 4 input cards to be inserted. The input cards are hot swappable, they may be plugged in and out while the projector is running.
4.0 CONNECTING SOURCES • using two VGA input boards. • using two SDI input boards. Using HDMI 1.4a Input Board The FORCE 3D is compatible and Plug and Play with most common used 3D sources such as Blu-Ray players, HD game console (Playstation 3) when connected to the HDMI 1.4a input board. The source format is automatically detected and displayed to the screen: The compatible signals are: • Blu-Ray movies <165 MHz up to 1080p24 - frame packing. • Games <165 MHz up to 720p60 frame packing.
4.0 CONNECTING SOURCES has been applied and the card is initialized, signal indicates a valid signal has been detected. Analog Input PWR Signal Red/Pr Green/Y Blue/Pb H/C V Analog BNC input board* 4.5 Dual-link DVI Input Board This card accepts a single DVI signal with or without High-Bandwidth Digital Content Protection (HDCP) video signal over a DVI-I connector and analog video signals over the DVI-I or 15-pin VGA connector.
4.0 CONNECTING SOURCES This card accepts and decodes standard definition (SD) video. This includes CVBS (composite video), SVideo, and component sources. This card supports as many as 6 video signals, four of them on BNC connectors and two on 4pin mini-DIN connectors. Each mini-DIN connector accepts 1 S-Video signal.
5.0 REMOTE CONTROL 5.0 REMOTE CONTROL This section describes the controls and switches used for basic projector operation once it is properly installed, aligned and configured. 5.1 Using the Remote Keypad or Built-In Keypad The projector is typically controlled using one of the following keypads: • Remote Keypad for wired or wireless control up to 25 feet (8m) away (includes cable for use as a wired remote).
5.
5.0 REMOTE CONTROL • Auto Initiates an automated process in which the projector optimizes critical display parameters such as size, position, pixel tracking, etc., for the current source. These parameters are listed in table below. An auto setup can save time in perfecting a display and you can modify the adjustments as desired.
5.0 REMOTE CONTROL good detail in dark areas when using the Gamma control. The nominal setting for Gamma Correction of 0 is correct for most signals and conditions. If excess ambient light washes out the image and it becomes difficult or impossible to see details in dark areas, increase the gamma correction setting to compensate. • Number Keys Press 1 to 9 to enter a value in a text box or to select a menu item. • 10+ Press 0 before pressing another number to enter a number greater than 9, e.g.
5.0 REMOTE CONTROL The number in the “Enter Number” window indicates which projector is currently listening to commands, and will match the projector number that has been defined in the Menu Preferences menu. The PROJ check box (read-only) shows whether or not the projector physically connected to a keypad is listening to commands from that keypad. A checkmark means that connected projector is listening; if there is no checkmark, you are communicating with a different projector.
5.0 REMOTE CONTROL Built-in Keypad LCD screen Soft Keys Navigation Keys Power Key Menu Exit Lens Exit Key Menu Key Enter Auto Key Help Key Lens Key Help Auto Input Key Input Shutter Shutter Key Built-in Keypad with LCD The built-in keypad has a LCD status display window which displays all states of the keypad controls. The LCD displays status information when the projector is powering up “Warm up: Lamp is warming up and when the projector is cooling down “Cool down: Lamp is cooling down.
6.0 MENU AND PICTURE SETTINGS Always remains in the enabled state when the power is ON. If the power is off the Menu key is disabled. • Soft Key Used to select an action indicated by text above the key on the LCD. If no text is shown, the associated key is disabled. 6.0 MENU AND PICTURE SETTINGS 6.1 Menu Structure MAIN MENU SUBMENU 1. Size and Position 1. Resize Presets AVAILABLE OPTIONS 2. Size 3. Vertical Stretch 4. Pixel Track 5. Pixel Phase 6. H-Position 7. V-Position 8.
6.0 MENU AND PICTURE SETTINGS 2. Image Settings 6. Input Levels 11. Color Enable 7. Advanced Image Settings 1. Gamma Settings 1. Gamma Correction 2. Gamma 3. Gamma Function 4. Gamma Slope 2. Detail Settings 1. Detail 2. Texture Enhancement 3. Detail Threshold 4. Detail Overshoot 5. Split Screen 3. Noise Reduction Settings 1. Noise Reduction 2. Block Artifact Reduction 3. Mosquito Noise Reduction 4. Split Screen 4. Color Settings 1. Select color Adjustment 2. Color Temperature 5. Dynamic Iris 1.
6.0 MENU AND PICTURE SETTINGS 3. Channel Setup List of all the channel names Press to select a channel 1. Edit Channel Card type H-Freq V-Freq Interlaced Sync source 1. Name 2. Channel 3. Slot 4. Input 5. In Menu 6. Auto Select 7. Locked 8. Previous Channel 9. Next Channel 2. Copy Channel 3. Delete Channel 4. Delete Unlocked only 5. Delete all Channels 4. Configuration 1. Language 2. Output Options 1. Screen Image orientation 2. Reserved 3. Reserved 4. Frame Locking 5. Frame Delay 6.
6.0 MENU AND PICTURE SETTINGS 4. Configuration 6. Menu Preferences 1. Large Menu Font 2. Menu Location 3. Horizontal Shift 4. Vertical Shift 5. Display Channel List 6. Display Slidebars 7. Display Error Message 8. Splash Screen Setup 9. OSD Transparency 10. Menu Type 11. Splash Screen 12. Cascading Menus 7. Communications 1. Serial (RS-232 IN) Options 1. Baud Rate (IN) 2. Serial Flow Control (IN) 3. Serial Mode (IN) 4. Serial Protocol (IN) 2. Serial (RS-232 OUT) Options 1. Baud Rate (OUT) 2.
6.0 MENU AND PICTURE SETTINGS 4. Configuration 8. Geometry & Color 3. Brightness Uniformity 1. Enable Brightness Uniformity 2. Test Pattern 3. Coarse Adjustment 4. Lamp Menu 5. Top Left Corner 6. Left Side 7. Bottom Left Corner 8. Top Right Corner 9. Right Side 10. Bottom Right Corner 11. Left Center 12. Right Center 13. Overall Gain 14. Restore Default 4. Edge Blending 1. Enable Edge Blending 2. Test Pattern 3. Left Blend Width 4. Right Blend Width 5. Top Blend Width 6. Bottom Blend Width 7. Lamp Menu 8.
6.0 MENU AND PICTURE SETTINGS 4. Configuration 8. Geometry & Color 7. Black Level Blending 1. Black Blend Enable? 2. Test Pattern 3. Left Blend Width 4. Right Blend Width 5. Top Blend Width 6. Bottom Blend Width 7. Center Brightness 8. Left Brightness 9. Right Brightness 10 Top Brightness 11. Bottom Brightness 12. Top Left Brightness 13. Top Right Brightness 14. Bottom Left Brightness 15. Bottom Right Brightness 8. Default Color Adjustment 9. Default Color Adjustment with YNF 9.
6.0 MENU AND PICTURE SETTINGS 4. Configuration 11. Option Card Settings (This menu will be filled with types that match cards plugged in) 5. Analog BNC Input Card 1. Connector Grounding 2. Red Odd Pixel Offset 3. Green Odd Pixel Offset 4. Blue Odd Pixel Offset 5. Red Odd Pixel Gain 6. Green Odd Pixel Gain 7. Blue Odd Pixel Gain 8. Odd Pixel Phase Offset 9. Pixel Phase 10. Input Level Detector 11. Level Detector Threshold 12. Auto color Enable 13. Color Enable 12. Dynamic Iris 1. Enabled 2.
6.0 MENU AND PICTURE SETTINGS 7. Input Switching & PIP 5. PIP Size & Position 5. Pixel Phase 6. PIP H-Position 7. PIP V-Position 8. PIP Blanking 1. Top Blank 2. Bottom Blank 3. Left Blank 4. Right Blank 6. PIP Image Settings 1. Contrast 2. Brightness 3. Color Space 4. PIP Video options 1. Enable Decoder AGC 2. Video Standard 3. Input Video Black 4. Color 5. Tint 6. Filter 7. Sampling Mode 8. Film Mode Detect 9. Chroma/Luma Delay 10. Adaptive Contrast 11. RGB Quantization Range 5. PIP Input Levels 1.
6.0 MENU AND PICTURE SETTINGS Main Menu 1. Size and Position 2. Image Settings 3. Channel Setup 4. Configuration 5. Lamp 6. Status 7. Input Switching & PIP 8. Language English 9. Test Pattern Off Main Menu With a function menu displayed, enter a menu option number for any numbered option, or use the UP/DOWN ARROW KEY to highlight the desired option and then press ENTER. Long menus have a scroll bar on the right— use the arrow keys to access the remainder of the menu.
6.0 MENU AND PICTURE SETTINGS of key presses. Slide bars in menus The current value for a given parameter, such as size or vertical stretch, appears to the left of its slide bar icon (adjustment window). This number often expresses a percentage, or it may have units associated with it (such as pixels), depending on the specific option. Press LEFT/RIGHT ARROW KEY to gradually adjust the setting up or down—both the number and the length of the bar change accordingly. Hold for continuous adjustment.
6.0 MENU AND PICTURE SETTINGS Press RIGHT ARROW KEY to move the cursor forward or LEFT ARROW KEY to move the cursor backwards as desired. to move the cursor (highlight) my video to select and go to next char. to scroll alphabet, numbers, etc Entering Text Edit a character • To edit a highlighted character, use UP ARROW KEY and DOWN ARROW KEY to scroll through the alphabet, numbers, spaces and punctuation available.
7.0 USING INPUTS AND CHANNELS 7.0 USING INPUTS AND CHANNELS The projector stores and recalls up to 99 different channels (source setups) for a variety of inputs. This memory feature allows you to define and use a variety of customized setups. Depending on what you have defined, each physical source connection (i.e., input at the projector) can have several different channels associated with it. 7.1 How to select an Input or a Channel Input An input is a source physically connected to the projector.
7.0 USING INPUTS AND CHANNELS first channel with matching characteristics. Creating a New Channel To use a new source with the projector, a new channel must be created so that the projector will respond to an input signal from that source. A new channel can be created automatically, or it can be copied from an existing channel and then edited as necessary.
7.0 USING INPUTS AND CHANNELS Composite Sync on the H/C input or the V input (4-wire). These abbreviations are preceded by either an ‘i’ (interlaced signals) or ‘p’ (progressive signal).
7.0 USING INPUTS AND CHANNELS Operation submenu. Select Delete and press ENTER. A window will appear to confirm the deletion of this channel. Channel Setup 01. 02. 1,2 4,1 iSVid pDig ENTER 15.73kHz- i59.94-Hz33.72kHz+ p29.
7.0 USING INPUTS AND CHANNELS define up to 99 channels. Slot 1-4, corresponding to which slot in the projector’s input panel the source is connected: Input 1-6, corresponding to which input on the selected slot the source is connected to. In Menu If checked (default, except for automatically defined channels with unchanged parameters), this defined channel will then appear in the list available when CHANNEL key is pressed.
8.0 ADJUSTING THE IMAGE 8.0 ADJUSTING THE IMAGE The most commonly used options for image adjustments are accessed through two menus: Size and Position (MENU 1) and Image Settings (MENU 2), both of which appear in the Main menu. From either of these two menus. You can change settings affecting the image from the current channel by working with the appropriate slide bars, check boxes and pull-down lists.
8.0 ADJUSTING THE IMAGE Size and Position 1. Resize Preset 2. Size No Resizing 0.729 3. Vertical Stretch 1.000 4. Pixel Track 858 5. Pixel Phase 0 6. H-Position 360 7. V-Position 262 8. Keep Aspect on Auto Setup 9.
8.0 ADJUSTING THE IMAGE Size Controls both the image width and height in tandem, maintaining the current aspect ratio of the displayed signal data. Vertical Stretch Adjusts the height of the image while keeping the width constant. Use “Vertical Stretch” to change the aspect ratio of the display. Pixel Track Steady flickering or several soft vertical stripes or bands across the entire image indicates poor pixel tracking.
8.0 ADJUSTING THE IMAGE factors. Blanking of a primary image. NOTE: Blanking a PIP image resembles zoom. For example, left Blanking zooms the right side of the PIP image; Right Blanking zooms the left side. There are no black bars. Blanking of a PIP image is similar to a zoom function. 8.2 Image Settings Menu Use the Image Settings menu to alter your main image without affecting its size or position. Changes made are applied immediately and are saved when you exit the menu (press EXIT or MENU).
8.0 ADJUSTING THE IMAGE • Select YPbPr (Video) with a standard definition televised signal (SDTV). • Select YPbPr (HDTV) with a high definition televised signal (HDTV). NOTE: When certain RGB signals are first connected, the projector may not recognize them as RGB and will incorrectly decode their color information as YPbPr (video). These signals can include: • RGB signals in NTSC, PAL, SECAM frequency ranges. • Scan-doubled sync-on-green. • Scan-quadrupled sync-on-green.
8.0 ADJUSTING THE IMAGE • Filter The proper filter setting is automatically set for virtually all signals, and rarely needs to be changed. Override only if standard pixel tracking and phase adjustments do not adequately clear up a “noisy” video signal, or if a graphics signal appears overly “soft”. Both instances indicate that “Filter” may be set to the wrong option. • Sampling Mode Sets the color sampling mode for a digital signal to either YCbCr 4:4:4, RGB or YCbCr 4:2:2.
8.0 ADJUSTING THE IMAGE Good RGB or input levels—that is, the drives and black levels for each of the three colors, red, green and blue— ensure that images from analog sources other than decoded video have maximum contrast without crushing black or white. By default (and in an “Auto Setup”), the projector automatically determines the best input levels by monitoring image content and adjusting the controls appropriately—further adjustment is typically not required to obtain proper blacks or whites.
8.0 ADJUSTING THE IMAGE and white edges are just visible and distinguished from neighboring pixels. Images from this source will then display correct blacks and whites without crushing. See figure Adjusting Input Levels Using the Peak Detector below. 1) Display a 16 level grayscale test pattern from the desired external source, and enter a checkmark in the Input Peak Detector check box.
8.0 ADJUSTING THE IMAGE or select an arbitrary gamma table that has been downloaded to the projector. NOTE: A separate PC utility is needed to do this. The 2.22 curve is a power curve typically used to encode graphics and video sources. The standard' curve (auto setup default) is a modified 2.22 curve with a small linear section in the black that enhances the detail in darker areas of the projected content. Typically standard or 2.22 is used for all sources.
8.0 ADJUSTING THE IMAGE appear bluish.
8.0 ADJUSTING THE IMAGE detail in affected areas (as the sensitivity control does) but merely reduces it. The amount of detail reduction depends on the average level of brightness in the scene, and the setting of this control. The brighter the scene the less impact this control will have. It is often best to adjust the sensitivity and white compression together to find the optimal settings. • Copy From This control allows you to copy the Dynamic Iris Settings from an existing profile to the current profile.
8.0 ADJUSTING THE IMAGE The 3D sync signal is generated by the 3D source to insure left/right eye content is synchronized to the projector and you. The projector has the ability to physically connect to two different sources. Ensure that the correct 3D sync input is selected (either Input A or Input B) with each 3D signal source.
8.0 ADJUSTING THE IMAGE Actual Frame Delay Displays the actual frame delay reading. It is read only. Full Screen Eye-Motion Filter Check this control to apply the Eye-Motion Filter to the entire screen, rather than applying just to the edge blending regions. Helps with posterization effects, sometimes seen in color ramps when viewing stereoscopic images. Eye-Motion Filter Adjust this filter to reduce saccadic eye-motion artifacts, sometimes noticeable in edge blending regions.
8.0 ADJUSTING THE IMAGE never the PIP image. Free Run sets the output to close to 60Hz for all sources. NOTE: When switching to a new input with framelocking enabled, the image will appear black for a short duration while the system locks onto the new input. • Frame Delay This control delays the output signal timing relative to the input signal timing by a fraction of a frame, and up to several frames. The minimum latency can vary based on the amount of scaling applied to the image.
8.0 ADJUSTING THE IMAGE • LCD Backlight Timer Set how long the LCD backlight stays on (in seconds) when in timer mode. • LCD Backlight Level Sets the LCD backlight brightness level. Maximum 25/Minimum 0. • Auto Power up If there is an AC power interruption, while Auto Power Up is enabled, the projector will resume operation in the same state as it left off.
8.0 ADJUSTING THE IMAGE • Display User Message Boxes Enable or disable the pop-up of message boxes that are directly triggered by user actions. Examples are gamma or lens control message boxes. • Display Error Messages Choose how you want to be notified of errors detected in either the incoming signal or projector. Select Screen or All (default) to see brief on-screen messages. This is recommended during setup or testing of the projector.
8.0 ADJUSTING THE IMAGE linking. 1. Seperate 2. RS-232 and RS-422 Joined 3. RS-232 and Ethernet Joined 4. All Joined - Networks do not communicate with one another - Serial Networks are joined but Ethernet is isolated - RS-232 and Ethernet are joined, but RS-422 is isolated - Network communication travel all networks Network Rooting List Ethernet Settings NOTE: Recommended for network administrators only.
8.0 ADJUSTING THE IMAGE Horizontal keystone is used to correct a keystoned image shape in which the left and right borders of the image are unequal in length, and the top and bottom are slanted to one of the sides, see Figure below. Horizontal Keystone All settings to adjust keystone are in the Geometry Correction submenu. Brightness Uniformity, Edge Blending and Black Level Blending should be disabled before performing Keystone adjustments.
8.
8.0 ADJUSTING THE IMAGE 2. Set Level Detector Threshold to near black (such as 200). 3. Adjust Offsets to minimize area of black stripe. 4. Set Level Detector Threshold to near white (such as 800). 5. Adjust Gains to minimize area of white stripe. • LEVEL DETECTOR THRESHOLD Input Level Value defines the value to be used by the Input Level Detector in recognizing blacks and whites. See Input Level Detector, above. • ASPECT RATIO OVERLAY Check this box to display an overlay pattern over the image.
8.0 ADJUSTING THE IMAGE Advanced Image Settings menu (“Select Color Adjustment”), and are not adjustable. DEFINING “USER” COLOR GAMUTS You may find the pre-defined “Select Color Adjustment” options do not suit your needs. For example, you may require a unique color gamut (range) for a single projector or application, or you may need to precisely match colors across multiple adjacent displays.
8.0 ADJUSTING THE IMAGE If necessary, you may want to use the “User” color adjustment to enable Color Adjustments by X,Y changes. Then enter the desired x/y values into each menu. • To match reds, decrease “Red X” until full field red screens match. • To match greens, decrease “Green Y” until full field green screens match. • To match blues, increase both “Blue X” and “Blue Y” until full field blue screens match. NOTE: For speed, enable the “Auto Color Enable” check box.
8.0 ADJUSTING THE IMAGE • Position Presets Set the location of the PIP (secondary) image in the display. PIP Image Settings - Submenu The controls adjust the PIP (secondary) image in the same fashion as their counter parts in the main Image Settings menu. NOTE: Refer to “Image Settings Menu”, page 53 for details of Contrast to Advanced Image Settings. PIP Border Width Enables the optional border around the PIP image. When enabled, a one pixel-wide border will surround the PIP image.
8.0 ADJUSTING THE IMAGE • Dual Lamp Use mode will use both lamps together. After 3 failed attempts to stay in Dual Lamp Use mode, the projector will switch to Single Lamp operation; however, the user-selected mode remains as Dual Lamp Mode. • Auto-Select a Single Lamp mode will choose the best lamp for single lamp operation.
8.0 ADJUSTING THE IMAGE 8.9 Status Menu The read-only Status menu lists a variety of details about the standard and optional components currently detected in the projector. Refer to the Status menu for versions of hardware and software installed, the type (size) of lamp, the hours logged in total and for a specific period (such as a rental period), and for your projector model name and serial number.
9.0 WEB USER INTERFACE 9.0 WEB USER INTERFACE 9.1 Logging On IMPORTANT Before logging on to the system, ensure that you select the appropriate language required. Your language selection only affects the web user interface. The language used by the projector’s on-screen display (OSD) is not affected. 1) Open your web browser and type the IP address (in the address bar) assigned to your projector. 2) Select the appropriate language from the Language drop-down list, located in the upper left-hand corner.
9.0 WEB USER INTERFACE 9.2 C These sections provide drop down list selection (refer to next chapter for more details) I Power Section. To power ON or OFF this unit. Only one button is enable. D Primary Tabs located along the top of the Main Window. J Shutter Section. To engage or not the shutter. Only one button is enable. E Current Status bar provides information messages according to the current status of this unit. K OSD (On Screen Display). To display or not the OSD.
9.0 WEB USER INTERFACE detailed information, refer to “Lens Installation”, page 9 Tools Tabbed Page - Virtual OSD Under the Tools tabbed page, select the Virtual OSD secondary tab to access to the virtual OSD page. See Figure below. C B A D E Tools Window A Virtual OSD tabbed page presents the Main Menu. D OSD Section contains an ON/OFF button. Only is available. Control of the OSD is always available through the remote. B The Maximize/Minimize toggle button.
9.0 WEB USER INTERFACE Clock Setting 1) Click within the field (i.e. Lamp Regeneration Start Time option) to allow access. 2) Change the Hour, Minute, and Seconds fields (double-digit field entry) as required. Admin Tabbed Page - System Under the Admin tabbed page, select the System secondary tab to upgrade, upload, backup and restore specific files, change the Logo position, background color, gamma properties, and select the interrogation level.
9.0 WEB USER INTERFACE a. Enter the Logo position for the X and Y fields. b. Click the Color square to open the Choose Background Color window, choose the desired background color from the color palette, and click OK. The color square changes to the selected color. c. Click the Upload button to display the Logo Upload window. Click Yes or No to confirm or cancel the upload. An Upload in Progress window appears. 4. Click the Upload button to display the Logo Upload window. a.
9.0 WEB USER INTERFACE NOTE: The scheduled tab is always selected by default on add. Scheduled Event Window 3) Select the frequency option for the event by selecting either Once, Daily, Weekly, or Monthly. NOTE: End Date is enabled when Daily, Weekly or Monthly repeat options are selected. 4) Click within the Start Time field to open a calendar pop-up window. 5) Navigate to and choose a desired date. The selected date will populate the Start Time field.
9.0 WEB USER INTERFACE Active column accordingly. RTE Listing Window • To add a System Event 1) Click Add to open the RTE Wizard. 2) Select the System Event tab. 3) Select a type of event from the System Event drop-down list. NOTE: Depending on the selection made, additional selections are made available in the second drop-down list located underneath (i.e. Input Change > Input 1, Slot 1). Add System Event • To Add a GPIO Event 1) Click Add to open the RTE Wizard. 2) Select the GPIO Event tab.
10.0 MAINTENANCE 10.0MAINTENANCE Installers, service trained operators and all other users must maintain a safe operating environment at all times. Read through this section in its entirety and understand all warnings and precautions before attempting to operate this projector. DANGER Always power down the projector and disconnect all power sources before servicing or cleaning. Read carefully the Safety Warnings and Guidelines below. 10.
10.0 MAINTENANCE The high-intensity lamps and electronics rely on a properly functioning cooling system. Regular maintenance of the cooling system is critical to prevent overheating and sudden projector failure and helps ensure reliable operation. Ventilation Vents and louvers in the projector covers provide ventilation, both for intake and exhaust. Never block or cover these openings. Do not install the projector near a radiator or heat register, or within an enclosure.
10.0 MAINTENANCE periodically in a clean, dust-free environment using a flashlight. Never touch an optical surface with your bare hands. Always wear latex lab gloves. Supplies or Cleaning Optical Surfaces • Soft camel-hair brush • Dust-free blower - filtered dry nitrogen blown through an anti-static nozzle. • Dust-free lens tissue, such as Melles Griot Kodak tissues (18LAB020), Optowipes (18LAB022), Kim Wipes or equivalent • For lens only.
10.0 MAINTENANCE To use lamp OFF command • In the lamp menu, select CHANGE LAMP. This will prompt for the old lamp serial number (if it was not previously entered). • Enter the new lamp serial number. NOTE: This action is not mandatory, it is recommended for accurate lamp statistics to be archived. Install the new lamp: • Take precaution to align the new lamp properly in the correct orientation inside the projector. • Press firmly to seat the lamps, ensuring the lamp is secure.
11.0 TROUBLESHOOTING 11.0TROUBLESHOOTING If the projector is not operating properly, note the symptoms and use this section as a guide to resolve the problem. If the problem cannot be resolved, contact your dealer for assistance. 11.1 Power Projector Does Not Power ON 1. Ensure projector is plugged in? Check power switch above power cord is in the ON position. 2. Check that the Status LEDs are ON. While the projector is busy initializing, the LEDs should be cycling.
11.0 TROUBLESHOOTING and go to the Main Menu>Configuration>Communication submenu and check the check boxes for Front IR Enabled and Rear IR Enabled are checked. Enable them if they were disabled and try again. 4. Projector is busy. If the projector is busy in a warm-up mode or in a cool-down mode, the commands from the remote keypad may be ignored. Wait until the projector reaches a stable state (Power ON or Stand By) and try again. 5. Press the PROJ key on the remote keypad.
11.0 TROUBLESHOOTING The Upper Portion of the Display is Waving, Tearing or Jittering This can occur with video or VCR sources. Check your source. Portions of the Display are Cut Off or Warped to the Opposite edge Resizing may need adjustment. Adjust until entire image is visible and centered. Display Appears Compressed (Vertically Stretched) 1. The frequency of the pixel sampling clock is incorrect for the current source. 2.
12.0 APPENDIX: SPECIFICATIONS 12.0APPENDIX: SPECIFICATIONS 12.
12.0 APPENDIX: SPECIFICATIONS Single lamp Full white ANSI 13-pt. (w/o electronic correction.) +25%, -35% Full white ANSI 13-pt. (w/ electronic correction.) +5%. -5% Full black ANSI 13-pt. Negative uniformity shall be between -35% and 0% and positive uniformity shall be between 0% and +35%. Color Uniformity Full white ANSI 13-pt. ±0.005 cluster on u’,v’ chart (CIE 1976) Full black ANSI 13-pt. ±0.
12.0 APPENDIX: SPECIFICATIONS • • Manual control 1/3 pixel fine movement control per button press on any applicable User Interface (e.g., remote).
12.0 APPENDIX: SPECIFICATIONS • Green – Projector is powered up and operating normally • Flashing green/yellow – Projector communication in progress • Flashing red – Error has occurred.
12.0 APPENDIX: SPECIFICATIONS electromagnetic compatibility (EMC). • FCC Part 15, Subpart B Class A; CISPR22/EN55022; CISPR24/EN55024 • UL 60950-1 First Edition; CAN/CSA-C22.2 No.
13.0 APPENDIX: INPUTS AND SIGNAL COMPATIBILITY 13.0 APPENDIX: INPUTS AND SIGNAL COMPATIBILITY 13.1 Analog (Only) Input Connectors: 5 female BNC, 75 Ohm • R/Pr • G/Y • B/Pb • H/C • V Color spaces/signal types: • RGB • YPbPr 13.2 Twin HDMI Input Connectors: • 2 independent HDMI inputs type A • 2 loop-out connectors type A Color spaces/signal types: • RGB • YCbCr (4:2:2) • YCbCr (4:4:4) HDCP support: • HDMI 1.
13.0 APPENDIX: INPUTS AND SIGNAL COMPATIBILITY • Dual HD input • SDI, HD-SDI 13.6 RS-232 Number of ports: 2 • Connector 1 female 9-pin Dsub (IN) • 1 male 9-pin Dsub (OUT) Max bit rate 115.2 kbps Flow control Xon/Xoff 13.7 RS-422 Number of ports: 1: Connector 1 female 9-pin Dsub Max bit rate 115.2 kbps Power output 12 V ±5% @ 400mA maximum 13.8 Ethernet Number of ports 1 Standard 10/100 Base-T Connector Female RJ-45 13.9 USB 2.
14.0 APPENDIX: GPIO 14.0APPENDIX: GPIO This section explains how to use a GPIO link from the projector to external equipment, such as devices for 3D synchronizing. 14.1 GPIO Port The GPIO connector located on the input panel provides a flexible method of interfacing a wide range of external I/O devices to the projector. There are 7 pins available on the 9pin D-Sub GPIO connector, which are configurable via RS-232 commands or Web interface. See Figure B-1 GPIO Connector.
14.0 APPENDIX: GPIO closing event. PIN Open (0 or Low) PIN Closed (1 or High) • Examples: Turn room lighting on when the projector is turned off. (Assumes a control/automation unit is configured to turn the lights on when pin 2 of its input goes high.
15.0 APPENDIX: PROJECTION DISTANCES 15.0APPENDIX: PROJECTION DISTANCES The projection distance are calculated from the middle of the front feet of the projector to the projection screen. 15.1 ABSOLUTE HD LENS 0.67:1 Projection Screen Size Diagonal size (Aspect Ratio 16:9) Projection Screen Size Base size (Aspect Ratio 16:9) Projection Screen Height (Aspect Ratio 16:9) ABSOLUTE HD LENS FIXED 0.67:1 Projecting Distance 70" (1778 mm) 61.0" (1550 mm) 34.3" (872 mm) 1,21 m 83" (2108 mm) 72.
15.0 APPENDIX: PROJECTION DISTANCES 15.3 ABSOLUTE HD LENS 1.16 to 1.49:1 Projection Screen Size Diagonal size (Aspect Ratio 16:9) Projection Screen Size Base size (Aspect Ratio 16:9) Projection Screen Height (Aspect Ratio 16:9) ABSOLUTE HD LENS ZOOM 1.16:1.49:1 Projecting Distance minimum - maximum 92" (2337 mm) 80.2" (2037 mm) 45.1" (1146 mm) 2,57 m - 3,24 m 100" (2540 mm) 87.2" (2214 mm) 49.0" (1245 mm) 2,77 m - 3,50 m 110" (2794 mm) 95.9" (2435 mm) 53.
15.0 APPENDIX: PROJECTION DISTANCES 15.5 ABSOLUTE HD LENS 1.8 to 2.6:1 Projection Screen Size Diagonal size (Aspect Ratio 16:9) Projection Screen Size Base size (Aspect Ratio 16:9) Projection Screen Height (Aspect Ratio 16:9) ABSOLUTE HD LENS ZOOM 1.8-2.6:1 Projecting Distance minimum - maximum 34,6 m 68" (1727 mm) 59.3" (1505 mm) 33.3" (847 mm) 2,83 m - 4,00 m 80" (2032 mm) 69.7" (2032 mm) 39.2" (996 mm) 3,30 m - 4,69 m 97" (2464 mm) 84.5" (2147 mm) 47.
15.0 APPENDIX: PROJECTION DISTANCES 15.7 ABSOLUTE HD LENS 4.1 to 6.9:1 Projection Screen Size Diagonal size (Aspect Ratio 16:9) Projection Screen Size Base size (Aspect Ratio 16:9) Projection Screen Height (Aspect Ratio 16:9) ABSOLUTE HD LENS ZOOM 4.1-6.9:1 Projecting Distance minimum - maximum 134 m 76" (1930 mm) 66.2" (1682 mm) 37.3" (946 mm) 11,83 m - 12,04 m 100" (2540 mm) 87.2" (2214 mm) 49.0" (1245 mm) 11,83 m - 15,71 m 127" (3226 mm) 110.7" (2812 mm) 62.
16.0 APPENDIX: DIMENSIONS 11.0’’ 565 mm 590 mm 22.3’’ 23.2’’ Ext. 20.6’’ 522 mm 280 mm 16.0 APPENDIX: DIMENSIONS 565 mm 22.
16.0 APPENDIX: DIMENSIONS Contact Information: TEC - Cineversum 7, rue La CAILLE, 75017 Paris - FRANCE Web: www.cineversum.