Installation Guide

ManualsBrandsCinch Systems ManualsElectronicsRF-SHK-319-NN, RF-SHK-319-ELK

RF-SHK-319 – NN Wireless TOTAL Window Sensor

I-RF-SHK-319 Rev.2 Nov 2018

Description

The RF-SHK-319-NN is a wireless window

sensor designed for dual protection; open

and close and to detect vibrations made by

an intruder attempting to break a window.

The shock sensor contains a piezo

detection device that detects vibrations

when mounted on a window frame. The

detection circuit can be adjusted for

sensitivity during installation to ensure

maximum coverage. The device also has a

built-in reed switch to monitor the open and

close of the door or window.

When activated, the sensor transmits a

signal to the control panel. These are the

signals the unit provides: supervisory,

tamper and low battery (as needed). The

sensor is powered by (2) replaceable 3-

VDC, lithium coin-cell batteries.

Installation Guidelines

• Mounting the sensor on metal can affect

the transmitting range performance.

Therefore, test the sensor from the desired

location using the installer sensor test,

before permanently mounting it.

• Mount the sensor within 100 ft. of the

panel.

• Mount the sensor on the frame of the door

or window.

• The sensors can be mounted to either

wood or metallic surfaces.

• After mounting the sensor, test the sensor

using the procedure in the section “Testing

the Sensor”.

Mounting the Sensor

Mount the sensor using the supplied

mounting screws for permanent mounting

installations or using the supplied double-

sided tape is optional.

Note: The gap between the sensor and

magnet should not exceed a maximum of

3/8”.

Mounting Screws

1. Remove the sensor base from the

sensor.

2. Place the sensor base in desired location

and mount the base with the supplied

screws. Attach the sensor to the base.

3. Mount the magnet into the desired

location using the supplied screw and lock

washer, making sure the alignment mark

lines up with the sensor mark.

Double-Sided Tape

1. Before applying double-sided tape,

ensure that the desired location is a smooth,

clean and dry surface.

Note: When applying the double-sided tape,

evenly apply pressure to ensure a good

surface contact.

Summary of content (4 pages)

PAGE 1
RF-SHK-319 – NN Wireless TOTAL Window Sensor Description The RF-SHK-319-NN is a wireless window sensor designed for dual protection; open and close and to detect vibrations made by an intruder attempting to break a window. The shock sensor contains a piezo detection device that detects vibrations when mounted on a window frame. The detection circuit can be adjusted for sensitivity during installation to ensure maximum coverage.
PAGE 2
RF-SHK-319 – NN Wireless TOTAL Window Sensor 2. Apply double-sided tape to the bottom of the sensor and the magnet. Mount the sensor and magnet at the desired locations, ensuring the alignment marks line up with each other. magnet to trip the reed, and learn-in the shock zone by tapping on device to activate it. Programming The following steps describe the general guidelines for programming the sensor into panel memory. Refer to the specific panel’s documentation for complete programming details. 1.
PAGE 3
RF-SHK-319 – NN Wireless TOTAL Window Sensor (CW). These setting are marked on the PCB. In maximum sensitivity mode, the least amount of shock is required to activate a shock alarm If the potentiometer is set all the way Low (CCW) the shock portion of the device is turned off and only the internal reed switch is active Note: If a low battery alarm occurs, replace the battery within 7 days.
PAGE 4
RF-SHK-319 – NN Wireless TOTAL Window Sensor This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s).