User's Manual

ManualsBrandsCinch Systems ManualsElectronicsDoor/window and garage sensors used by security systems

Mini DW Sensor—Installaon Instrucons

Micro Wireless Sensor and Accessories

1 - RF-MDWS Sensor 1- Mounng Tape 1 - RF-MDWS Magnet 2 - Baeries ( 2- 3VDC CR 2032) Instrucons

Tamper

switch

Doc # I-RF-MDWS Rev. A Sep 2014

Installaon

1. Remove the transmier’s cover by pressing in on the

small rectangular latch on the end of the cover and

li up

2. Mount the sensor base directly to the surface using

the mounng tape provided. Make sure to align the

mounng tape with the tamper pull put area on the

boom of the sensor to insure proper tamper opera-

on.

3. Mount the magnet next to the sensor and align the

magnet with the mark on the side of the sensor,

using the mounng tape provided

4. Remove the baery isolator tabs from both baeries

on the sensor

5. Replace the cover on the transmier

6. Enroll the senor into the control panel according the

instrucons

Note: Mounng the transmier onto metal surfaces may

impact the eecve range of the transmier

Cover

Latch

Cover

Latch

Tamper

Base

Note: Baery Safety

Observe polarity when inserng

replacement baeries to avoid

damaging the sensor.

Risk of re, burns and explosion.

Do not recharge, disassemble, burn

or expose baeries to tempera-

tures above 100C (212F)

Dispose of used baeries properly

and in accordance with all local

laws

Keep baeries away from children

Baeries

Mini DW Sensor—Installaon Instrucons

Micro Wireless Sensor and Accessories

1 - RF-MDWS Sensor 1- Mounng Tape 1 - RF-MDWS Magnet 2 - Baeries ( 2- 3VDC CR 2032) Instrucons

Tamper

switch

Doc # I-RF-MDWS Rev. A Sep 2014

Installaon

1. Remove the transmier’s cover by pressing in on the

small rectangular latch on the end of the cover and

li up

2. Mount the sensor base directly to the surface using

the mounng tape provided. Make sure to align the

mounng tape with the tamper pull put area on the

boom of the sensor to insure proper tamper opera-

on.

3. Mount the magnet next to the sensor and align the

magnet with the mark on the side of the sensor,

using the mounng tape provided

4. Remove the baery isolator tabs from both baeries

on the sensor

5. Replace the cover on the transmier

6. Enroll the senor into the control panel according the

instrucons

Note: Mounng the transmier onto metal surfaces may

impact the eecve range of the transmier

Cover

Latch

Cover

Latch

Tamper

Base

Note: Baery Safety

Observe polarity when inserng

replacement baeries to avoid

damaging the sensor.

Risk of re, burns and explosion.

Do not recharge, disassemble, burn

or expose baeries to tempera-

tures above 100C (212F)

Dispose of used baeries properly

and in accordance with all local

laws

Keep baeries away from children

Baeries

Summary of content (2 pages)

PAGE 1
Mini DW Sensor—Installation Instructions Micro Wireless Sensor and Accessories 1 - RF-MDWS Sensor 1- Mounting Tape 1 - RF-MDWS Magnet Installation 1. Remove the transmitter’s cover by pressing in on the small rectangular latch on the end of the cover and lift up 2. Mount the sensor base directly to the surface using the mounting tape provided. Make sure to align the mounting tape with the tamper pull put area on the bottom of the sensor to insure proper tamper operation. 3.
PAGE 2
FCC label statement: Mounting “This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” Specifications: Dimensions: 2.25 X 1 X .5 2.25” Using pre-cut tape, mount the sensor on the non-moving frame and the magnet on the door or window .