WF-610User Manual Version 2 TABLE OF CONTENTS
1 Quick Start ................................................................................................................... 4 1.1 Connect PoE Adapter to WF-610............................................................................................ 12 1.2 Configure PC’s IP Address...................................................................................................... 13 1.3 Visit WF-610 Web Page .........................................................................................
5.2 Software Upgrade.................................................................................................................... 29 5.3 Factory Reset via WEB ........................................................................................................... 29 5.4 Reboot via WEB ...................................................................................................................... 30 5.5 Factory Reset via Sending Special Packet .................................................
1 Quick Start Thank you for buying this product. The following information aims to give you general information about product introduction, product overview and installation procedure and so on. 1. Introduction WF-610 is a dual-band 2x2 outdoor Wi-Fi AP, which is complied with the IEEE802.11n/11ac standard and designed for high-density deployments in offices, schools, hospitals and hotels that require premium performance.
4. Installation To reduce the risk of bodily injury, electrical shock, fire, and equipment damage, read all warnings and precautions in this guide before installing or maintaining product. Caution To avoid risk of injury from electrical shock or energy hazard, installation and service of this product must be performed by qualified service personnel.
2. Put the U shaped screw stem and U shaped slot into the hole. And then drive the M6 crew nut and M6 washer. 3. Install the clamp on the back of WF-610, with M6*12 screw bolt, M6 spring washer and M6 flat washer. Four screw bolts need be installed. 4. Input M6*12 screw bolt and M6 washer into the hole on the back and drive them. 5. Finall y mount WF610 on the pole as shown in the picture. And drive the screw nut tight with wrench.
5. LED Definition LED RUN LAN Function State-Color AP power / ready Steady - Green status Red Off Network Link Status Steady - Green Steady- Yellow 0 1 Flashing Off 5G Hz Radio Status Steady– Green Off 2.
2. Input the default IP address 192.168.188.251 in the address bar of the web browser and press Enter. 3. Enter username and password (username: admin, password: password), after password authentication is successful, the web page is displayed. 7. Product Specification Physical specification Dimensions 216.2mm x 216.2 mm x 71mm(L x W x H) Weight 3.0kg LED RUN/ LAN/ RADIO 0/ RADIO 1 Ethernet interface RJ-45 connector Electrical specification Power input Power consumption Standard 802.3at PoE ≤12.
IP67 Dustproof and waterproof Lightning protection 6KV common mode surge 8. Product Proper Disposal Waste of Electrical and Electronic Equipment Directive 2002/96EC on Waste of Electrical and Electronic Equipment are designed to tackle the fast increasing waste stream of electrical and electronic equipment and complements European Union measures on landfill and incineration of waste.
（Plastic and Polymeric Parts） O： 表示该有毒有害物质在该部件所有均质材料中的含量在 SJ/T11363 － 2006 标准规定的限量要求下。 Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard. X： 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T113632006标准规定的限量要求。 Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
FAQ The LAN port indicator is off. Solution Check whether the connection between the LAN/POE port of the combiner and the LAN/POE port is correct. Check whether the connection between the LAN/POE port of the combiner and the LAN/POE port is correct. 11. Technical Support CIG offers technical support 24 hours a day, 7 days a week. Use one of the following methods to contact CIG technical assistance center: Hotline: +86 21 8023 300 Email: support@cambridgeig.com 12.
13. Legal declaration CIG name, CIG logo, and all CIG product names are trademarks of Cambridge Industries Group Co. Ltd (CIG). All other brand and product names are claimed as property of others respective holders. Specifications, products, and products names are subject to change without notice. Copyright This document may not be reproduced in whole or in part without the express written permission of CIG.
1.2 Configure PC’s IP Address Notes: Connect your PC to the “LAN-IN” port on PoE Adapter of WF-610, manually configure your wired NIC with a static IP address on the 192.168.188.x subnet (e.g. 192.168.188.202). 1.3 Visit WF-610 Web Page Notes: Input the default IP address “192.168.188.251”in the address bar of browser.
default username and password (username: admin, password: password) to enter the Web interface of AP. 1.4 Configure Management Interface for WF-610 Notes: You can configure management IP/subnetmask/gateway/DNS here. By default, packets are sent without tag. Packets can be sent with tag by selecting the option as shown in the figure. 1.
1.6 Configure Location, Language Notes:The country code is US and can’t be modified. 1.7 Configure Security Profile for Different Authentication Types 1.7.
WEP-Shared Key: 1.7.2 WPA2-PSK Notes: With parameter “Encryption”, you can select AES, TKIP or AES/TKIP. 1.7.3 WPA/WPA2-PSK Notes: With parameter “Encryption”, you can select AES, TKIP or AES/TKIP. 1.7.4 802.1X /EAP If want to use the 802.1x authentication, it need to configure the Radius profile firstly. Then in the security profile, the radius profile will be cited by security profile.
Notes:Security type can be WPA2 or WPA/WPA2. 1.7.5 WEB/MAC WF-610 supports Web/MAC authentication. If you want to use the Web/MAC authentication, it needs to configure the Portal profile and Radius profile firstly. Then in the security profile, the Portal profile and Radius profile will be cited.Above all, you need to setup a portal server and radius server. Notes: MAC and WEB authentication have the same configuration. Afterreceiving auth request from station, WF-610 will firstly start MAC auth.
Notes: Wall garden can be configured by inputting custom domain or IP. User can visit these domains or IP listed in wall garden before authentication. For those domains or IP not contained in wall garden, they can be visited only after authentication.
2 AP Mode 2.1 AP Network Topology 2.
2.3 Configure Radio Parameters 2.
Notes: 1. You may apply the Security, Rate Limit or MAC ACL profiles which have been configured. After the above setting, wireless stations can connect to the SSID of AP and get IP address from DHCP server to visit Internet. 2. VLAN mode and PVID used for Ethernet traffic can be configured here. 2.5 Configure Rate Limit Rule (Optional) Notes: Rate Limit profile will be applied in the SSID configuration. 2.6 Configure Group ID (Optional) Notes: Group profile is used for 802.1x/Web/MAC authentication.
Filter-ID can be matched with one profile, the traffic VLAN and rate limit will be applied to the station. The Group profile is applied in the Radius server profile.
2.7 Configure MAC ACL Rule (Optional) 2.8 AP+WDS WF-610 also supports AP+WDS mode. 2.8.1 AP+WDS Network Topology 2.8.
Note: Enable WDS function when you configure SSID. 2.8.3 Configure CPE WDS Note: Enable WDS function too when you configure CPE to connect to AP.
3 WDS Bridge Mode 3.1 WDS Bridge Network Topology 3.2 Enable WDS Bridge Mode Note: Please select a specified Channel (for example 161) here. 3.
Note:Security profile can be cited here, but only WEP auth and OPEN are supported for WDS bridge mode. 3.4 Configuration on Remote AP Note: Please select the same channel. For the WDS bridge mode, two APs should use the same channel and security encryption. Note: Please input the MAC address of AP which you want to connect via WDS. 3.5 NAWDS Auto Find WF-610 also supports “NAWDS Auto Find” function. Input the MAC address of the slave AP on the master AP.
Notes: Please select the same Channel as that of AP which you want to connect via WDS. Notes: After you enable “NAWDS Auto Find” function, the AP will connect to the master AP via WDS automatically. 4 Status 4.1 Overview You can check some summary info here, for example, software version, ip interface and radio configuration.
4.2 Radio In this page, you can see service mode for radio 2.4G is AP mode. There is only one SSID “2g_ssid1” with BSSID 00:00:11:11:11:10 and totally two stations are connected to this radio. Information will be updated by clicking “Refresh” button. For radio 5G, you can open “status”-“Radio 5G” to check detailed information. Something to mentioned, detailed information about station (e.g. auth type/MAC/online time/TX bytes/RX bytes) exists in “station list”.
5 Management 5.1 Backup/Import Configuration Notes: Press “Save” button to save current configuration. If you want to import one new configuration file, please click “choose file” to select the new file and then press “Upload” button to upload. After that, WF-610 will reboot. 5.2 Software Upgrade Notes: Press “Choose File” button to select firmware file that you want to upgrade, then press “Upgrade” button to upgrade. 5.3 Factory Reset via WEB Click “Restore” button to do factory reset.
5.4 Reboot via WEB 5.5 Factory Reset via Sending Special Packet WF-610 has no reset button. If you forget WF-610’s IP, you can use a simple tool— anysendtcpip to execute factory reset via sending special packet. After that, you can telnet WF-610 with default IP 192.168.188.251. 5.5.1 Factory Reset One Single Device Open file folder.
Double click anysend.exe. Click the yellow icon located top left corner，and select .
Select right network card which is used to send packet. Modify the MAC address marked in red to beWF-610’s MAC with which you want to do factory reset.
Click the yellow icon located top right corner, then it will start to send special broadcast packet. After devices receive the packet, they will check if it matches with their own MAC. If it does, device will execute factory reset. If not, device will do nothing. 5.5.2 Factory Reset All Devices Select and open . Here you can see one special default MAC address marked in red color whichis 00:01:02:03:04:05. You don’t need to modify it.
6 Troubleshooting 6.1 Ping Diagnose 6.
6.3 LED Definition LEDs are defined as follows: Label Function LED mode RUN AP power / ready Off status Red On - Green LAN Ethernet Network Off Link Status / On - Yellow Activity On - Green (HW Control) Flashing 5G Radio 5G Hz Radio Status Off On – Green 2.4G Radio 2.4G Hz Radio Off Status On – Green 6.4 Debug via Telnet You can debug WF-610 via Telnet.
Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
