WF-180 Wireless Access Point
Thank you for buying this product. The following information aims to give you general information about product introduction, product overview and installation procedure and so on. 1. Introduction WF-180 is a dual-band 2x2streams and chains indoor Wi-Fi AP, which is complied with the IEEE802.11n standard and designed for high-density deployments in offices, schools, hospitals and hotels that require premium performance.
Console port Also names as RJ-11, used to manage WF-180 software. Reset button Pressing the button longer than 5s to restore the device to factory defaults and reset the device. DC power connector used for connecting the power adapter USB port supports a USB 2.0 connector(Support up to 0.5A) Kensington Lock Slot For additional security 4.
Installation tool: • Screws and screw-driver Installation site: Please ensure the visibility of product and no tall buildings and woods block between them. Installation procedure Wall mounting 1. Drive two screws fist in the wall. The distantbetween two screws mounted on the wall is 40mm. 2. Align bracket with the screw, and then pull down the bracket with up to down direction until it has been fixed tightly.
3. Align the securing hookof AP with bracket, and push AP from up to down until it has been locked fully. Ceiling mounting: 1. Fasten ceiling rails by pushing bracket as the indicated direction 2. Secure the screw to fasten bracket assembly.
2.3.
3.4. Go through locking holes by cable-tie to safely content AP with bracket 5.
2. 3. Input the default IP address 192.168.188.251 in the address bar of the web browser and press Enter. Enter username and password (username: admin, password: password), after password authentication is successful, the web page is displayed. 7. Product Specification Physical specification Dimensions 160 mm x 160 mm x 40mm(Width x Length x Height) Weight Less than 1kg LEDs RUN,LAN,5GHz,2.
Working humidity 5% ~ 95% non-condensing Elevations 86kPa~106kPa Dustproof and waterproof IP30 Lightning protection 4KV common mode surge 8. Product Proper Disposal Waste of Electrical and Electronic Equipment Directive 2002/96EC on Waste of Electrical and Electronic Equipment are designed to tackle the fast increasing waste stream of electrical and electronic equipment and complements European Union measures on landfill and incineration of waste.
es) 金属部件 (Metal Parts) O O O O O O 塑料和聚合物部件 (Plastic and Polymeric Parts) O O O O O O O: 表示该有毒有害物质在该部件所有均质材料中的含量在 SJ/T11363 - 2006标准规定的限量要求下。 Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.
FAQ Solution Check that the power adapter is plugged into a live AC outlet. Check the power cable for shorts or breaks. The RUN indicator is off. Check whether the connection between the LAN/POE port of the combiner and the LAN/POE port is correct. The LAN port indicator is Check whether the connection between the LAN/POE port off. of the combiner and the LAN/POE port is correct. 12.11. Technical Support CIG offers technical support 24 hours a day, 7 days a week.
America Parkway, Suite 320 Santa Clara CA 95054. Tel: +1 408.730.6888 14.13. Legal declaration CIG name, CIG logo, and all CIG product names are trademarks of Cambridge Industries Group Co. Ltd (CIG). All other brand and product names are claimed as property of others respective holders. Specifications, products, and products names are subject to change without notice. Copyright This document may not be reproduced in whole or in part without the express written permission of CIG.
Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IC Radiation Exposure Statement for Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
forth for an uncontrolled environment”. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.