CAMBRIDGE CIG Industries (Group) Co Ltd.
TABLE OF CONTENTS 1 Safety........................................................................................................................... 3 2 Overview ...................................................................................................................... 3 3 Installation of device .................................................................................................... 6 3.1 3.2 Installation tools and environment....................................................
1 Safety Do not install the device near the power line, electric lamp, power grid, or in any forceful power grid place, which is to avoid the AP abnormal work. Ensure the power adapter is grounded well if install the device indoor. Install other lightning protection equipment near the device if necessary, because the limitation of lightning protection module inside the device is 6KV. Use the steady power grid to provide the power to the device, which is to avoid the abnormal work.
Figure 1 Network Application for indoor coverage Figure 1 Network Application for cellular coverage Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
Figure 2 Network Application for wireless bridge Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
3 Installation of device 3.1 Installation tools and environment Installation tools: A laptop, super category5 outdoor network cables, a screwdriver, two wrenches, screws and a pole (optional). Installation environment: Need to ensure that it is visible between the AP and terminals and no tall obstacles between them. 3.2 Installation Steps 1. Mount the AP on the pole, and should confirm AP is fixed well. Use one RJ45 cable or SFP to connect the AP POE port.
Figure5 Pole mounting 2. Connect the WAN POE port of the WF-0613A and the POE port of the adaptor by a network cable, and connect the LAN port of the adaptor and another network device (Laptop, switch etc.) by another network cable (or optical fiber). And then power on the adapter. Check the status of indicators of the WF-0613A. The detail Indicators refer to Figure 7.
Figure6 Ports of the adaptor Note: The longest length of the network cable plugged in to the POE port is up to 100m, and the network cables should comply with the YD/926.2 protocol.
5 Thin AP mode basic configuration Note: When do the thin AP settings, make sure the AP mode first, and then select the appropriate method to do the basic setting. 5.1 Login to the Web interface and setting from FAT AP mode 1. Power on WF-0613A, and connect the LAN port (refer to Figure 6) to laptop; 2. Set the laptop wired NIC IP address to 192.168.188.X (X is an any number except 251 and 255), and the subnet mask is set to 255.255.255.0.
Figure9 Web interface 4. In the Web interface, Select “Management” tab, then select “FIT/FAT” in the lefthand navigation tree, to do the setting. Select “FIT” in the “Mode” option. Figure10 FIT AP setting 5. Here are two options in “Find AC”, “Auto” and “Static”. i. If you select “Auto” mode, AP will use DHCP to get IP address from AC. Before you active the function, you should setting the AC host name and domain name.
Figure11 Find AC in auto mode ii. if you select “Static” mode. AP will use static IP register AC. Fill in AP static IP, Mask, Gateway and AC IP address is a MUST. Then click the change” button. Figure12 Find AC in static mode 5.2 Login to the Web interface and setting from Thin AP mode 1. Power on WF-0613A; 2. Set the user computer wireless NIC IP address to 192.168.188.X (X is an any number except 251 and 255), and the subnet mask is set to 255.255.255.0. The method is the same as 5.1 step 1. 3.
connect. The SSID is named as “CIG2.4G_xxxxxxxxxxxx” in 2.4 GHz or “CIG5.8G_xxxxxxxxxxxx” in 5.8 GHz (the “xxxxxxxxxxxx” is the MAC address of AP) and it is encrypted as WPA/PSK. Use Windows wireless tool to connect the SSIDs with password “CIGW8888”. Figure13 Thin AP SSID broadcast 4. After connect with AP SSID, input the default IP address “192.168.188.251”in the address bar of browser. Then enter the default username and password (username: admin, password: password) to enter the Web interface. 5.
3. Before connect with the SSID, PC wireless NIC should be set as static IP ( the procedure is the same as 5.1 step 1), then it can connect with AP and use telnet or Web to catch all the information we need. Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation.
Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
