Version 2 CAMBRIDGE CIG Industries (Group) Co Ltd.
TABLE OF CONTENTS 1 Quick Start ................................................................................................................... 3 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 2 Introduction ................................................................................................................................ 3 Product Overview ...................................................................................................................... 3 Installation...............................
1 Quick Start Thank you for buying this product. The following information aims to give you general information about product introduction, product overview and installation procedure and so on. 1.1 Introduction WF-630R1 is a dual-band 802.11ac 2x2 outdoor Wi-Fi AP module, which is complied with the IEEE802.11n/11ac standard and designed for high-density deployments in offices, schools, hospitals and hotels that require premium performance.
1.3 Installation To reduce the risk of bodily injury, electrical shock, fire, and equipment damage, read all warnings and precautions in this guide before installing or maintaining product. Caution To avoid risk of injury from electrical shock or energy hazard, installation and service of this product must be performed by qualified service personnel.
On - Green Device ready 1.5 Software Installation Logging in to the Web Page 1. To configure PC IP address, fill 192.168.188.x in “IP address” and 255.255.255.0 in “Subnet mask”(set Window7 as an example to show the properties). 2. Input the default IP address 192.168.188.251 in the address bar of the web browser and press Enter. 3. Enter username and password (username: admin, password: password), after password authentication is successful, the web page is displayed. 1.
Ethernet interface RJ-45 connector Electrical specification Power input Standard 802.3at PoE Power consumption ≤24W Environmental specification Working temperature -40℃~ +70℃ Working humidity 5% ~ 95% non-condensing Elevations 86kPa～106kP0061 Lightning protection 6KV common mode surge 1.
（Cr6+） O 电路模块 × （circuit modules ） O 电缆及电 x 缆组件 （Mecha nicalass emblies ） O 金属部件 O （Metal Parts） O 塑料和聚 O 合物部件 （Plastic and Polymeric Parts） （PBB） （PBDE） O O O O O O O O O O O O O O O O O：表示该有毒有害物质在该部件所有均质材料中的含量在SJ/T11363 －2006 标准规定的限量要求下。Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.
作。The Environment-Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here, unless otherwise marked. Certain parts may have a different EFUPand so are marked to reflect such. The Environment-Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual. 1.
2.1 Connect PoE Adapter to AP Notes: Please connect the Ethernet Port labeled “PWR LAN-OUT” on PoE Adapter to “ETH1” port of AP and the Ethernet Port labeled “LAN-IN” on PoE Adapter to your PC or Switch. Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation.
2.2 Configure PC IP address Notes: Connect your PC to the “LAN-IN” port on PoE Adapter of AP, manually configure your wired NIC with a static IP address on the 192.168.188.x subnet (e.g. 192.168.188.202). Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation.
2.3 Visit AP Web page Notes: Input the default IP address “192.168.188.251”in the address bar of browser. Then enter the default username and password (username: admin, password: password) to enter the Web interface of AP. 2.4 Configure IP address for AP Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation.
2.5 Connect AP to Switch Notes: Connect AP to Switch and confirm it can visit Internet, then configure your PC to the same subnet and connect to the same Switch in order to continue to configuring the AP. 2.6 Configure location, Language and Country code for AP Notes:The country code is US and can’t be modified.
2.7 Configure detailed WiFi parameters for AP 2.8 Configure Radius parameters for AP Notes: If want to use the 802.1x authentication, it need to configure the Radius profile firstly. Then in the security profile, the radius profile will be presented in the drop-down list.
2.9 Configure Portal parameters for AP Notes:The AP can support Web authentication based onChillispot. If want to use the Web authentication, it need to configure the Portal profile and Radius profile firstly. Then in the security profile, the Portal profile and Radius profile will be presented in the drop-down list.Above all, you need to setup a Web authentication server and radius server.
2.10 Configure security parameters for AP Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
PSK 802.1x Authentication Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
Web Authentication 2.11 Configure Rate limit rule (Optional) Notes: Rate Limit profile will be cited in the AP configuration. Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
2.12 Configure Group ID (Optional) Notes: Group profile is used for 802.1x/Web authentication. Group is classifiedby Filter-ID attribute in radius access accept message. The Group is bound with the role of the user. Different group has different VLAN and rate limit configuration. When a station sends the username and password to the Radius server for authentication, the server can respond with a Filter-ID (optional) to the AP.
2.13 Configure MAC ACL rule (Optional) Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
2.14 Configure SSID Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
Notes: You may apply the relevant Security, Rate Limit, Mapping or MAC ACL profiles which you configured here. After the above setting, wireless stations can connect to the relevant SSID of AP and get IP address from DHCP server of firewall to visit Internet. Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation.
3 AP WDS Network Topology 3.1 Enable WDS function Note: Enable WDS function when you configure SSID. Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
3.2 Configure CPE WDS Note: Enable WDS function too when you configure CPE to connect to AP. Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
4 NAWDSNetwork Topology 4.1 Configure WDS bridge mode Note: Please select a specified Channel(for example 161) here. Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
4.2 Input remote AP MAC 4.3 The configuration in remote AP Note: Please select the same Channel as the Channel ofAP which you want to connect via WDS. Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
Note: Please input the MAC address of AP which you want to connect via WDS. Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
4.4 NAWDS Auto Find WF-630R1also supports “NAWDS Auto Find” function, after you configure master AP, you mayenable “NAWDS Auto Find” function in slave AP. Notes: Please select the same Channel as the Channel of AP which you want to connect via WDS. Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation.
Notes: After you enable “NAWDS Auto Find” function, the AP will connect to the master AP via WDS automatically. 5 Station Network Topology Notes:WF-630R1 supports station mode. WF-630R1 access to the AP by Wi-Fi, and provide the Ethernet access to the client by the LAN port. 5.
5.2 Station Access to AP Notes:Need to configure the SSID manually. If want to use the security method, need to configure the “security profile” firstly and then cite it here. Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
5.3 Station Status Notes: After WF-630R1 access to a AP successfully, can check the station status on the Web GUI, for example, the SSID and BSSID. 6 Troubleshooting 6.1 Ping Diagnose Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
6.2 TraceRT Diagnose 6.3 How to backup/restore setting Notes: Press “Save” button to save current setting. Press “Upload” button to load saved setting. Notice CIG has the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, CIG has the final interpretation. This version is effective in the two months since the release date.
6.4 How to upgrade AP Notes: Press “Choose File” button to select firmware file, then press “Upgrade” button to upgrade AP. 6.5 How to reset AP to default setting Notes: If you can’t visit AP web page, please press the “Reset” button of AP and hold for more than 5 seconds, the AP will reset to defaultsetting automatically. Or you can do it by the Web GUI.
Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
