User's Manual

ManualsBrandsCIDMATE International Technology ManualsElectronics900 MHz Analog Cordless Phone

Security System

Your cordless telephone uses a digital coding security system to prevent unauthorized use of

your telephone line by another nearby cordless telephone. The system has its own identifying

signal created by microcomputers in both the BASE UNIT and the HANDSET.

Security Code

This telephone has an internal security code with 65,536 possible combinations.

Resetting Security Code and Channel Information

Communication between the HANDSET and the BASE UNIT may not be possible in any of the

following situations:

1. After a power failure.

2. After relocating the BASE UNIT by disconnecting the AC ADAPTER.

3. After replacing the HANDSET BATTERY PACK.

To reset, place the HANDSET on the BASE UNIT for 2 to 5 seconds.

Multi-Channel Access

Your cordless telephone lets you select a channel from the 40 frequencies available to transmit

signals between the BASE UNIT and HANDSET. When you notice interference from other

cordless telephones, change to another channel by pressing the button on the

HANDSET.

DELETE

SCAN

Security

Summary of content (11 pages)

PAGE 1
Security Security System Your cordless telephone uses a digital coding security system to prevent unauthorized use of your telephone line by another nearby cordless telephone. The system has its own identifying signal created by microcomputers in both the BASE UNIT and the HANDSET. Security Code This telephone has an internal security code with 65,536 possible combinations.
PAGE 2
Recharging the BATTERY PACK Battery Type Use the following type and size of BATTER Y PACK: Cordless Telephone BATTERY PACK 3.6V, 600mAh U.S. Electronics Inc. Ni-Cd Battery Pack: Model B650 Ni-Cd This BATTERY PACK is available through: U.S. Electronics Service Center 105 Madison Avenue New York, NY 10016 1-800-825-5208 NOTES: 1. During a power interruption, the BASE UNIT does not operate, and a phone conversation cannot be made on the HANDSET. 2.
PAGE 3
Changing the BATTERY PACK Changing the Battery Pack The BATTERY PACK provides power for the HANDSET of your cordless telephone. To Replace BATTERY PACK: 1. Remove the HANDSET BATTERY COMPARTMENTCOVER by sliding it down. 2. Pull out the BATTERY PACK PLUG and remove the BATTERY PACK. 3. Plug the new BATTERY PACK into the BATTERY CONNECTOR. 4. Slide the HANDSET BATTERY COMPARTMENT COVER firmly into place in its closed position. 5. Before use, charge the new BATTERY PACK for 12 hours.
PAGE 4
Problem Solving Problem Solving Section For your assistance, we have listed below a few common problems. Phone does not work, check the following: 1. 2. 3. 4. BASE UNIT is plugged into a power source. HANDSET is charged. TONE/PULSE Select switch is in the right position. TELEPHONE LINE CORD is plugged into the TELEPHONE JACK. Range of phone limited, check the following: 1. ANTENNAon BASE UNIT is raised. 2. BASE UNIT is centrally located in your residence. 3. BASE UNIT is not located near appliances.
PAGE 5
Technical Information Technical Information This cordless telephone uses radio frequencies to allow mobility. There are certain difficulties in using radio frequencies with a cordless telephone. While these are normal, the following could affect the operation of your system. Noise Electrical pulse noise is present in most homes at one time or another. This noise is most intense during electrical storms.
PAGE 6
FCC Requirements Federal Communications Commission Requirements This equipment complies with Part 68 of the FCC rules. A label on the BASE UNIT of the equipment contains, among other information, the ACTA Product Number and the Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company.
PAGE 7
FCC Requirements Federal Communications Commission Requirements (continued) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 8
Warranty Warranty Information BellSouth Products One-Year Limited Warranty This limited warranty sets forth all BellSouth Products responsibilities regarding your telephone. There are no other expressed or implied warranties from BellSouth Products. Warranty Service Provided If you purchased the telephone new from a retail vendor, BellSouth Products warrants the telephone against defects in material and workmanship for a period of one (1) year from the original date of purchase.
PAGE 9
Warranty What To Do for Warranty Service During the first thirty (30) days, a defective product is eligible for over-the-counter exchange at the retailer from whom it was purchased. After thirty (30) days, the defective product should be returned to the authorized service center. Please allow 2-3 weeks for the return of your telephone product. The shipping address of the authorized service center is: U.S.
PAGE 10
Wall Mounting Template This page serves as a template for attachment of screws to the wall when mounting this telephone on the wall. 1. Cut out this page. 2. Use this template to determine the distance between screws when mounting this phone on the wall. The two cross hairs identify where to attach the screws.
PAGE 11
IMPORTANT In order to get maximum life from the HANDSET BATTERY PACK, be sure to charge the HANDSET for 12 hours before initial use. IMPORTANT Placing your BASE UNIT near appliances such as televisions, refrigerators, radios, or microwave ovens may cause interference. IMPORTANT When you hear interference, press the DELETE button to change the operating SCAN channel. IMPORTANT The AC ADAPTER must always be plugged into an electrical outlet.