User's Manual

ManualsBrandsChungear Industrial ManualsElectronicsCeiling Fan Remote Controller (Transmitter)

LCD TOUCH SCREEN

OPERATION AND INSTALLATION INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

1. Read and keep this instruction sheet carefully.

2. Please note that all fixed wiring appliances should be installed by a qualified electrician.

3. The supply to the receiver should be connected on its own circuit.

4. Switch off the power at main power box before working on receiver or ceiling fan.

5. Install receiver into the canopy of ceiling fan per Fig’s 1 and 2.

6. This unit is to be used for the control of ceiling fan and its electrical source must be AC 110/120V, 60Hz.

7. Do not install in damp location or immerse into water. (For indoor use only)

8. Do not drop or bump the unit.

9. Do not use with solid state ceiling fans.

10. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable (rheostat) wall control.

INSTALLATION INSTRUCTIONS

1. After switching power off, remove ceiling fan canopy from the mounting bracket. Disconnect existing wiring between ceiling fan and

supply at electrical junction box.

2. Slide the receiver into the mounting bracket as shown (see Fig.1) being careful not to pinch the antenna wire. The receiver will be

inserted between the down rod and the mounting bracket.

3. Make wiring connections per Fig,2 & 3. CAUTION: Incorrect wire connection can damage this receiver and could cause injury or fire.

4. Push all connected wires back into the junction box and reinstall the canopy onto the mounting bracket.

5. Manually set fan speed control to HIGH and set light to ON using the pull chains.

LEARNING PROCESS (SMART SYNC)

1. After installation is complete and power is turned on, remove the battery cover on transmitter. Insert batteries (4 AAA, included). NOTE:

Do not mix old and new batteries, alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.

2. Use a small screwdriver or ballpoint pen to press and hold the “LEARN” key, located in the battery compartment, for 3 seconds. Fan will

turn on at high speed and light (if installed) blinks 3 times. This confirms that the LEARNING setting is active. Tap FAN key to turn off the

fan. CAUTION: User must press “LEARN” key within 30 seconds after main power on. It is not necessary to redo the LEARNING setting

if just replacing batteries.

3. If user cannot finish the setting within the 30 seconds timeframe, please turn off the main power and re-start the power again. This will

reset the unit. Repeat step 2 until the LEARNING feature is activated as indicated.

4. CAUTION: If the settings on the LCD readout do not synchronize with the fan after initiating the learning process, press Fan or Light key

to resume the settings.

DIMMER / ON OFF SETTING (D/O)

Slide the D/O switch, located in the battery compartment, to match the bulb type in your fan. “D” for incandescent bulbs and “O” indicates

compact fluorescent bulbs (CFL). Use a small screwdriver or ballpoint pen to slide firmly left or right. CAUTION: Incorrect setting can

damage the receiver.

TRANSMITTER FUNCTIONS

Fan – Tap lightly to turn fan on or off.

Fan Speed Control – Tap lightly to cycle through the fan speed settings displayed on the LCD readout.

Light –Tap lightly to turn light on or off. Hold down for 2 seconds to cycle through dimmer setting. The light key has an auto resume feature

so the light will re-activate at the same brightness as the last time it was turned off. NOTE: The dimmer function does not work with CFL

bulbs.

Walk Away Light Delay – Tap once - the light and fan turn off after 1 minute. Light on the fan blinks once to confirm function is active. Press

any key to cancel function.

Home Shield – Press and hold for 3 seconds. Light on the fan blinks two times to confirm function is active. Fan will be off and the light will

randomly turn on and off while you are away. To deactivate press any key once.

D/O – Set the light for use with incandescent bulbs or compact fluorescent bulbs (CFL). NOTE: Factory setting is CFL.

LEARN – Set the transmitter and receiver work synchronizes.

Receiver Installation

(Do Not Pinch Antenna Wire)

AAA

D/O

LEARN

Wall Mount Holder

Made in China

NOTE: For the remote to work properly fan must be on HIGH speed and lights must be ON prior to use.

Fig. 1

Antenna

Fan

Fan Speed Control

Walk Away Light Delay

Light

Home Shield

Learn

D/O

MODEL:TR60B-L

Summary of content (2 pages)

PAGE 1
LCD TOUCH SCREEN OPERATION AND INSTALLATION INSTRUCTIONS Antenna NOTE: For the remote to work properly fan must be on HIGH speed and lights must be ON prior to use. IMPORTANT SAFETY INSTRUCTIONS 1. Read and keep this instruction sheet carefully. 2. Please note that all fixed wiring appliances should be installed by a qualified electrician. 3. The supply to the receiver should be connected on its own circuit. 4. Switch off the power at main power box before working on receiver or ceiling fan. 5.
PAGE 2
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.