User's Manual

LIGHT AND AIR CONTROL PLUS
OPERATION AND INSTALLATION INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
1. Read and keep this instruction sheet carefully.
2. Please note that all fixed wiring appliances should be installed by a qualified electrician.
3. The supply to the receiver should be connected on its own circuit.
4. Switch off the power at main power box before working on receiver or ceiling fan.
5. Install receiver into the canopy of ceiling fan per Fig’s 1 and 2.
6. This unit is to be used for the control of ceiling fan and its electrical source must be AC 110/120V, 60Hz.
7. Do not install in damp location or immerse into water. (For indoor use only)
8. Do not drop or bump the unit.
9. Do not use with solid state ceiling fans.
10. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable (rheostat) wall control.
INSTALLATION INSTRUCTIONS
1. After switching power off, remove ceiling fan canopy from the mounting bracket. Disconnect existing wiring between ceiling fan
and supply at electrical junction box.、
2. Slide the receiver into the mounting bracket as shown (see Fig.1) being careful not to pinch the antenna wire. The receiver will
be inserted between the down rod and the mounting bracket.
3. Make wiring connections per Fig,2 & 3. CAUTION: Incorrect wire connection can damage this receiver and could cause injury
or fire.
4. Push all connected wires back into the junction box and reinstall the canopy onto the mounting bracket.
5. Manually set fan speed control to HIGH and set light to ON using the pull chains.
LEARNING PROCESS (SMART SYNC)
1. After installation is complete and power is turned on, remove the battery cover on transmitter. Insert batteries (1x 12V, included).
NOTE: Do not mix old and new batteries, alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
2. Use a small screwdriver or ballpoint pen to press and hold the “LEARN” key, located in the battery compartment, for 3 seconds.
Fan will turn on at high speed and light (if installed) blinks 3 times. This confirms that the LEARNING setting is active. Tap FAN
OFF button to turn off the fan. CAUTION: User must press “LEARN” key within 30 seconds after main power on. It is not
necessary to redo the LEARNING setting if just replacing batteries.
3. If user cannot finish the setting within the 30 seconds timeframe, please turn off the main power and re-start the power again.
This will reset the unit. Repeat step 2 until the LEARNING feature is activated as indicated.
DIMMER / ON OFF SETTING (D/O)
Slide the D/O switch, located in the battery compartment, to match the bulb type in your fan. “D” for incandescent bulbs and “O”
indicates compact fluorescent bulbs (CFL). Use a small screwdriver or ballpoint pen to slide firmly up or down. CAUTION: Incorrect
setting can damage the receiver.
TRANSMITTER FUNCTIONS
High / Medium / Low Speed – Tap lightly to turn the fan on at high, medium or low speed respectively.
Fan Off – Tap lightly to turn the fan off.
Light – Tap lightly to turn light on or off. Hold down for 2 seconds to cycle through dimmer setting. The light button has an auto
resume feature so the light will re-activate at the same brightness as the last time it was turned off. NOTE: The dimmer function
does not work with CFL bulbs.
Walk Away Light Delay – Tap once - the light and fan turn off after 1 minute. Light on the fan blinks once to confirm function is
active. Press any button to cancel function.
D/O – Set the light for use with incandescent bulbs or compact fluorescent bulbs (CFL). NOTE: Factory setting is CFL.
LEARN – Synchronizes transmitter and receiver signals.
Antenna
Receiver Installation
(Do Not Pinch Antenna Wire)
Wall Mount Holder
NOTE: For the remote to work properly fan must be on HIGH speed and lights must be ON prior to use.
Fig. 1
High Speed
Medium Speed
Walk Away Light Delay
Light
Learn
Low Speed
D/O
Fan Off
MODEL:TR123A