WIRELESS WEATHER STATION C-8154 USER’S INSTRUCTIONS P17815400030
p.
The multifunctional weather station is equipped with many functions providing thorough weather information to you. The receiver unit has a clear, easy-to-read display that shows weather forecast, indoor temperature, pressure, moon phase, time and date, as well as the temperature measured and transmitted by the sensor. It is able to receive and display readings from up to 3 remote sensors.
FCC Remarks: MAIN FEATURES: WEATHTER STATION: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
0.1 ºC / 1ºF (above 0 ºC) 1 ºC / ºF (below 0 ºC) Temperature resolution: RF transmission frequency: No of remote unit: RF transmission range: Temperature sensing cycle: Pressure measuring range: Pressure sampling cycle: Moon phase scanner range: Radio controlled signal: Power: Main unit: 433MHz up to 3 units Maximum 30 meters around 60 ~ 64 seconds 800mb to 1050mb 15 minutes From 2000 to 2050 DCF77, MSF, WWVB 4.5 V, use 3 x AA 1.5V alkaline battery 3 V, use 2 x AAA 1.
- In case of mal-function, the unit may be required to reset. 8. ºC / ºF: - Switch between ºC / ºF. 9. mb/hPa . inHg: - Switch between mb/hPa or inHg. Fix the separate wall-mounting stand on the wall by screws. Push the stand of the clock upward, hang it on the wall-mounting stand by its recessed holes. For the transmitter, fix the wall-mount holder on the wall or simply place it on the table. 10. TABLE STAND - use to stand on desktop 11. WALL-MOUNTING HOLE: - Use to support the main unit on wall. 12.
LOW BATTERY INDICATOR When the battery does not have enough power to operate the unit, the low battery indicator will appear to remind you to replace with new batteries. Transmitter’s low battery indicator ( shows on transmitter ) Transmitter’s low battery indicator ( shows on the main unit) 16. INDOOR TEMPERATURE AND HUMIDITY WINDOW: - Shows the indoor temperature-trend, current temperature, or the maximum or minimum recorded temperature. 17.
1. LED indicator: - Flashes when the remote unit transmits a reading. 2. 3. LCD: - Displays the current temperature monitored by the remote unit . Channel slide switch: - Assign the transmitter to Channel 1, Channel 2 or Channel 3. 4. ºC / ºF: - Switches between ºC / ºF. 5. RESET: - Return all values to default value. 6. Battery compartment: - Accommodates 2 AAA size batteries. 7. Battery door 8. Wall mount holder: - Supports the transmitter in wall mounting. 9. Folding table stand p.
2. The weather forecast is meant for next 12 to 24 hours. It may not necessarily reflect the current situation. 3. The “Sunny” icon, when applies to nighttime, implies clear weather. Slightly cloudy Cloudy TENDENCY TENDENCY Rainy Storm TENDENCY Sunny TENDENCY BEFORE YOU BEGIN TRANSMITTER: 1. Remove the removable stand, unscrew the screws of the back cover and lift the cover off. 2. Insert 2 x AAA batteries into the battery compartment.
WEATHER STATION: WEATHER TREND 1. Remove the battery door and insert 3 x AA batteries into the battery compartment. Make sure you insert the batteries the right way round (see polarity information +/in the battery compartment). 2. Close the battery compartment. 3. Press reset button to re-start the clock and it will synchronise the channels of the transmitter automatically. The temperature-trend, and pressure-trend indicators show the trends of changes for the last few minutes.
1. Press MAX/MIN key to check Maximum temperature records. Press it twice to check the Minimum records. Press it thrice to exit. 2. Press and hold MAX/MIN key for 3 seconds to delete the records. MAX. Temperature record indicator, please set the weather forecast icon according to the current weather condition. 1. In normal time mode, press and hold DOWN key for 3 seconds, weather indicator flashing. 2.
NOTE: 1. Do not set the weather indicator when it is raining. Raining will give unstable data. 2. Do not set the weather indicator in night time. RECEPTION OF RADIO CONTROLLED TIME SIGNAL The time and date are radio-controlled. The current time and date are automatically synchronized with the time signal transmitted from Frankfurt, Germany (DCF77), UK/ (MSF) / US (WWVB) provided the device is within about of 1500 km range of the transmitter.
SETTING THE TEMPERATURE ALARM NOTE: Use this function to be woken up at a determined period of time earlier (1-30 minutes), if one of the transmitter’s temperatures is below -1ºC. 1. In normal time mode, press ALARM key twice to enter pre-alarm mode, press UP or DOWN key to turn pre-alarm on. 2. Press and hold the ALARM key for 2 seconds, pre-alarm time flashing, press UP or DOWN key to change its value. 1. Everyday the unit will automatically search for the time signal at 2:00, 8:00, 14:00 and 20:00. 2.
manually. As soon as the transmitter is received again, the clock will automatically synchronise with the received time. 1. In normal time mode, press and hold TIME key for 2 seconds, hour flashing, press UP or DOWN key to change its value. 2. Press TIME key again, minute flashing, press UP or DOWN key to change its value. 3. Repeat the above operation to set the time in this order: Hour - Minute - Second - 12/24 hour - Year - Month - Date - Day language. 4.