C8318A (WWVB) PD09025M Size: 105 x 130 (mm) RADIO CONTROLLED WIRELESS THERMO CLOCK USER’S INSTRUCTIONS P178318GB010
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate ratio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
MAIN FEATURES: WEATHER STATION gives you specific rights, and you may have other rights that vary from state to state. Printed in China SPC900 1 SHARP, registered in the U.S. Patent and Trademark Office 2 This device complies with Part 15 of the FCC Rules.
TWO YEAR LIMITED WARRANTY M.Z. Berger & Company warrants the original consumer purchaser of this product that it shall be free of defects in materials and workmanship for two years from the purchase date of this product. Defects caused by tampering, improper use, unauthorized modifications or repairs, immersion in water or abuse are not covered by this warranty. If a defect covered by this warranty occurs during the warranty period, wrap your clock carefully and send it to the following address: M.Z.
8. ALM ON/OFF key: - In normal time mode, press it to turn on/off alarm1 & alarm2. - In alarm time mode, press it to turn on/off alarm and temperature pre-alarm. - In alarm time mode, press and hold it for 2 seconds to enter the alarm time setting mode. - In alarm time setting mode, press it to step the setting items. - Press it once to stop the current alarm when it is sounding. 9. SYNC key: - Press and hold it for 3 seconds to turn on/off the signal reception of transmitter (915 MHz) manually. 10.
13. WALL-MOUNTING HOLDER: - Use it to support the main unit in the wall mounting. 14. TABLE STAND: - Use it to stand the clock on the desktop. 15. BATTERY DOOR TRANSMITTER SPECIFICATIONS MAIN UNIT 6 Recommended operating range: 0 °C to 45 °C 32 °F to 113 °F 1 2 3 5 4 Resolution: 0.1°C (above -9.9°C) 1°C (below -10°C) 0.1°F (-9.9°F ~ 99.9°F) 1°F (above 100°F & below -10°F) 7 6 1. LED indicator: - Flashes when the remote unit transmits a reading. 2.
5. BATTERY DOOR 6. WALL-MOUNTING HOLDER: - Use it to support the transmitter on the wall. For the transmitter, fix the separate wall-mounting stand outside in the area protected from direct rain by the screw. Once the stand is mounted, place the transmitter into the stand on the wall. Besides, you can also place it on the desktop by its table stand. 7. TABLE STAND: - Use it to stand the transmitter on the desktop. RECEPTION OF TRANSMITTER SIGNAL OPERATING THE WEATHER STATION 1. 2. 3. 4.
BATTERY REPLACEMENT OPERATING THE TRANSMITTER If the low battery indicator “ ” appears beside the outdoor temperature of main unit, it indicates that you should replace batteries of transmitter at once. While if the low battery indicator displays beside the indoor temperature, it means that the battery power of main unit is not enough and you should replace batteries of clock immediately. 1.
DAYLIGHT SAVINGS TIME (DST) HOW TO READ TEMPERATURE RECORDS The clock has been programmed to automatically switch when the daylight savings time is in effect. Your clock will show “DST” during the summer. Change the temperature unit to °C for Celsius or °F for Fahrenheit by pressing “°C/°F” key. SIGNAL STRENGTH INDICATOR 1. The signal indicator displays signal strength in 4 levels. Wave segment flashing means time signals are being received. The signal quality could be classified into 4 types: 2.
2. 3. 4. The temperature pre-alarm can sound 30 minutes earlier than the alarm only when the outdoor temperature is below 26.0°F (-3.0°C). If no key is pressed during the alarm period, the clock will enter the snooze mode automatically. Besides, you can also press “SNOOZE” key once to stop the current alarm and activate the snooze function. Once the snooze function is activated, the 4-step crescendo alarm will sound 13 times in 5-minute interval. The alarm duration is 60 seconds.
5. 6. Repeat the above operations (point 3, 4) to set the below items in this order: Date > Hour > Minute > Second > Day language > +/-23 hours time difference. Press “TIME” key to save and exit the setting mode, or let it exit automatically 30 seconds later without pressing any key. 3. 4. 5. 6. Press “UP” or “DOWN” key to change its value. Press “ALM ON/OFF” key once until the alarm Minute digit flashes. Press “UP” or “DOWN” key to change its value.
