User's Manual

ManualsBrandsChung's Electronic ManualsElectronicsWireless Weather Station (433.9MHz Tx)

Table Of Contents

Dimension: 40(W) x 131(H) x 23.5(D) mm

MULTI-CHANNEL CABLE FREE REMOTE THERMO-HYGRO SENSOR

MODEL: C-8201

USER’S MANUAL

INTRODUCTION

Thanks for your purchasing of the Remote Sensor. The Remote Sensor is used with the Chung’s

433MHz multi-channel In-Out wireless weather station to monitor the temperature and humidity

changes of remote or outdoor sites. Operation is easy and no wire installation is required.

MAIN FEATURES

1. LED INDICATOR

Flashing when the sensor transmitting a reading.

2.CHANNEL SLIDE SWITCH

Designate the channel of the sensor to Channel 1, Channel 2 or Channel 3.

3.RESET BUTTON

Reset all settings to default values

4.°C/°F

Switches between °C/°F.

5.BATTERY COMPARTMENT

Contains 2 AA size batteries.

6.BATTERY DOOR

Covers the battery compartment

7.WALL-MOUNT HOLDER

Support the sensor on wall

8.FOLDING TABLE STAND

For standing the unit on a flat surface

TRANSMITTER:

1. Remove the removable stand and screws the back cover off the transmitter.

2. Insert 2 x AA batteries into the battery compartment. Be sure to insert them the right way round (see

Summary of content (12 pages)

PAGE 1
MULTI-CHANNEL CABLE FREE REMOTE THERMO-HYGRO SENSOR MODEL: C-8201 USER’S MANUAL INTRODUCTION Thanks for your purchasing of the Remote Sensor. The Remote Sensor is used with the Chung’s 433MHz multi-channel In-Out wireless weather station to monitor the temperature and humidity changes of remote or outdoor sites. Operation is easy and no wire installation is required. MAIN FEATURES 1. LED INDICATOR Flashing when the sensor transmitting a reading. 2.
PAGE 2
polarity information +/- in the battery compartment). 3.The receiver can receive humidity and temperature data from up to 3 transmitters. Assign the channel to each transmitter, Channel 1, 2 or 3 respectively by sliding the switch besides the battery compartment. 4. Press the reset key of the transmitter individually by a pin to confirm the channel setting. 5. Select the temperature unit by sliding the °C/°F switch besides the battery compartment. NOTE: 1.
PAGE 3
2. Do not leave disabled battery in the watch for a long time and be sure to replace it with new ones. If battery fluid leaks out, it may damage movement components. 3. Avoid rough using or dropping the unit. 4. To clean the unit, use a dry soft cloth or a soft cloth moistened in a solution of water and a mild neutral detergent. Never use solvents (such as benzene, spray cleanser). 5. Always read the user’s manual thoroughly before operating the unit.
PAGE 4
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 5
MULTI-CHANNEL CABLE FREE REMOTE THERMO-HYGRO SENSOR MODEL: C-8202 USER’S MANUAL INTRODUCTION Thanks for your purchasing of the Remote Sensor. The Remote Sensor is used with the Chung’s 433MHz multi-channel In-Out wireless weather station to monitor the temperature and humidity changes of remote or outdoor sites. Operation is easy and no wire installation is required. MAIN FEATURES 1.LCD Displays the current temperature and humidity monitored by the remote unit alternately. 2.
PAGE 6
polarity information +/- in the battery compartment). 3.The receiver can receive humidity and temperature data from up to 3 transmitters. Assign the channel to each transmitter, Channel 1, 2 or 3 respectively by sliding the switch besides the battery compartment. 4. Press the reset key of the transmitter individually by a pin to confirm the channel setting. 5. Select the temperature unit by sliding the °C/°F switch besides the battery compartment. NOTE: 1.
PAGE 7
2. Do not leave disabled battery in the watch for a long time and be sure to replace it with new ones. If battery fluid leaks out, it may damage movement components. 3. Avoid rough using or dropping the unit. 4. To clean the unit, use a dry soft cloth or a soft cloth moistened in a solution of water and a mild neutral detergent. Never use solvents (such as benzene, spray cleanser). 5. Always read the user’s manual thoroughly before operating the unit.
PAGE 8
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 9
MULTI-CHANNEL CABLE FREE REMOTE THERMO-HYGRO SENSOR MODEL: C-8203 USER’S MANUAL INTRODUCTION Thanks for your purchasing of the Remote Sensor. The Remote Sensor is used with the Chung’s 433MHz multi-channel In-Out wireless weather station to monitor the temperature and humidity changes of remote or outdoor sites. Operation is easy and no wire installation is required. MAIN FEATURES 1. LED INDICATOR Flashing when the sensor transmitting a reading. 2.outer connect To test the temperature anywhere u need 3.
PAGE 10
3.The receiver can receive humidity and temperature data from up to 3 transmitters. Assign the channel to each transmitter, Channel 1, 2 or 3 respectively by sliding the switch besides the battery compartment. 4. Press the reset key of the transmitter individually by a pin to confirm the channel setting. 5. Select the temperature unit by sliding the °C/°F switch besides the battery compartment. 6. Use the outer connect to test the temperature anywhere u like. NOTE: 1.
PAGE 11
2. Do not leave disabled battery in the watch for a long time and be sure to replace it with new ones. If battery fluid leaks out, it may damage movement components. 3. Avoid rough using or dropping the unit. 4. To clean the unit, use a dry soft cloth or a soft cloth moistened in a solution of water and a mild neutral detergent. Never use solvents (such as benzene, spray cleanser). 5. Always read the user’s manual thoroughly before operating the unit.
PAGE 12
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.