USER MANUAL W020 © 2015 SMANOS HOLDING LTD. All Rights Reserved. Printed in China PA: W020-UM-EN-V1.
Industry Canada Notice This device complies with Industry Canada licence-exempt RSS standard(s). 1. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Introduction In the Box Congratulations in buying the W020 alarm system. This product is a totally D.I.Y. home security solution. It features automatic connection to various accessories, putting your home under allround protection. To experience this wonderful product, please follow the instructions in the user manual. If there is any problem when using the product, please contact us for help. Please check whether the package includes the following items. If not, please contact the distributor/ retailer.
How It Works SA-A12 Adapter x 1 Reset Pin x 1 Paired Door/Window Contact Door or window is opened User Manual x 1 Warranty Card x 1 Managed by remote control / phone Panel sounds / Sends a push notification to users Users 03 04
Overview Accessories Front Remote Control Overview Status Indicator LED Indicator Status Status Indicator Indicator Arm Guide Point For The Blind Disarm Stay Rear SOS Battery Battery Battery _ + _ + Reset Button _ _ _ + + + _ + _ _ + _ _ + + + _ _ Reset Button Button Reset + + Metal Ring Note: If you press any button, the LED indicator is dusky and lights off after flashing twice quickly, means the remote control battery is exhausted.
The control panel will hoot on-site with indicator flashing, users will receive an emergency message from App. Press the [stay ] button, the indicator on the remote control blinks once, and then press [Arm ] button within 3 seconds to mutely arm the system. Press the [stay ] button, the indicator on the remote control blinks once, and then press [Disarm ] button within 3 seconds to mutely disarm the system. Overview Tamper Switch There are three zone modes available for the sensors.
Installation Make sure the contacts work properly before installation. Step 1: Choose a suitable installation location APP Operation Apple and Android App It can be installed on doors, windows or any other objects that can be opened or closed. If it is applied to metal doors, please place spacer under the transmitter and magnet. Download App from App Store or Google Play by searching keywords “W020 Alarm”. W020 Alarm The App can be bound with the alarm system through smart phones.
Registration and Network setup Option 2. Manual configuration 1. Hold the network configuration button on the control panel until the control panel beeps once, then the red and blue status indicators blink alternately, means the control panel has entered into a manual configuration state. 2. Find and choose the Wi-Fi named W020 in your phone’s Wi-Fi list. 3. Choose manual configuration in the one-click setup interface of W020 App. 4. Input the local Wi-Fi name and its password, click [Start].
System settings ③ Exit Delay Time & Entry Delay Time If you don’t want to carry along remote controls, you can set the exit or entry delay. Suppose entry delay is set at 30 seconds, the system will allow you 30 seconds to disarm the system before alarming. Suppose exit delay is set at 35 seconds, the system will allow you 35 seconds to leave before the system is armed. The “beep” is heard in every 2 seconds to remind you to leave. The pace of reminding sound will speed up in the last 15 seconds.
Pairing/Deleting Accessory When a beep is heard from the control panel means the sensor is paired successfully. If two beeps are heard, it means the sensor has already been paired. The included accessories have been paired with the control panel by default, if you want to pair new accessories, please follow these instructions: Note: To pair other sensors, please refer to the related user manuals.
Reload the Batteries of Accessories RE2300 Remote Control Restoring to Factory Setting Please read the steps below carefully before restoring to factory setting. Remove the rubber item Loose the screw Remove the rubber item Loose the screw Use the supplied reset pin to press the reset button (refer to page 5) for about 7 seconds, during the time, you will hear a beep in the first 3 seconds, do not loose it until another beep is heard. After that, the control panel is restored to factory setting.
Trouble Shooting Maintenance If the alarm system cannot work properly, please first check the following sheet. The alarm system features unique and brilliant design and craftwork. Please use it with caution. The following suggestions will help prolong the service life of the system.
8. The alarm system requires uninterrupted power supply for working or standby. Therefore, you need to connect the AC adapter to a reliable power outlet. 9. Avoid placing the control panel and sirens in bedrooms or offices, so as not to disturb your rest or work. 10. It is recommended to cut off the power if the system is not used for long time. 11. If the alarm system is covered with dirt, wipe off the dirt with soft cloth or tissue.
RE2300 Remote Control Power Supply Transmitting Current Transmitting Distance Radio Frequency Housing Material Operating Condition Dimensions DC 3V (CR2032 lithium cell battery x 1) <9.
FCC STATEMENT 1.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference. (2)This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.