User's Manual

ManualsBrandsChromagic Technologies ManualsElectronicsIn-Wall Switch Module

HAN02 IN-WALL SWITCH MODULE

This in-wall switch module is a transceiver which is a Z-Wave

enabled device and

is fully compatible with any Z-Wave

enabled network. Z-Wave

enabled devices

displaying the Z-Wave

logo can also be used with it regardless of the manufacturer,

and ours can also be used in other manufacturer’s Z-Wave

enabled networks.

Remote On/Off control of the connected load is possible with other manufacturer’s

Wireless Controller.

This in-wall switch module is able to detect overload wattage of connected

non-dimmable lights or appliances. When detecting overload state, the module will be

disabled and its On/Off button will be lockout of which LED will flash quickly.

However, disconnect and re-connect the wiring of the module will reset its overload

condition to normal status.

Adding to Z-Wave

Network

In the front casing, there is an On/Off button with LED indicator which is used to carry

out inclusion, exclusion, reset or association. Toggle On/Off button between On and

Off. When first power is applied, its LED flashes on and off alternately at 2-second

intervals. It implies that it has not been assigned a node ID and cannot work with

Z-Wave enabled devices. Put a Z-Wave

Controller into

inclusion/exclusion/association mode, the module executes the function of auto

inclusion.

Auto Inclusion

The function of auto inclusion will be executed as long as the module does not have

node ID when the first power is applied.

After node ID has been linked, auto inclusion will run automatically after the

execution of exclusion/reset is successful.

Note: Auto inclusion lasts for 4 minute or until the execution of inclusion is completed

during which the node information of explorer frame will be emitted once every 5

seconds. Unlike “inclusion” function as shown in the table below, the execution of

auto inclusion is free from pressing the On/Off button on the module.

Function Description LED Indication

No node ID After power is applied, if the module

does not record a node ID provided by

controller.

2-second on, 2-second off

1. Have Z-Wave Controller entered

inclusion mode.

Inclusion

2. Pressing On/Off button three times

within 1.5 seconds will enter

inclusion mode or

3. Close and open manual switch input

of S1 or S2 between C three times

within 1.5 seconds at the first 3

minute when the first power is

applied will enter inclusion mode

1. Have Z-Wave Controller entered

exclusion mode.

2. Pressing On/Off button three times

within 1.5 seconds will enter

exclusion mode or

3. close and open manual switch input

of S1 or S2 between C three times

within 1.5 seconds at the first 3

minute when the first power is

applied will enter exclusion mode

Exclusion

Node ID has been excluded

successfully.

2-second on, 2-second off

On/Off Button

LED Indicator

manual switch input

Summary of content (4 pages)

PAGE 1
Auto Inclusion HAN02 IN-WALL SWITCH MODULE The function of auto inclusion will be executed as long as the module does not have node ID when the first power is applied. TM This in-wall switch module is a transceiver which is a Z-Wave enabled device and is fully compatible with any Z-WaveTM enabled network. Z-WaveTM enabled devices displaying the Z-WaveTM logo can also be used with it regardless of the manufacturer, and ours can also be used in other manufacturer’s Z-WaveTM enabled networks.
PAGE 2
Reset 1. 2. Pressing On/Off button three times within 1.5 seconds will enter inclusion mode, within 1 second, press On/Off button again until LED is off or Close and open manual switch input of S1 or S2 between C three times within 1.5 seconds at the first 3 minute when the first power is applied will enter inclusion mode, within 1 second, Close manual switch input of S1 or S2 to C again until LED is off. 3. Association Home ID and node ID will be cleared and reset to factory default. 1.
PAGE 3
Initial state ON OFF action press and release the On/Off button press and release the On/Off button Programming final state OFF ON 1. Basic Command Class / Binary Switch Command Class 1-1 BASIC_GET / BINARY_SWITCH_GET Upon receipt of the following commands from a Z-Wave device, the module will send Basic Report Command / Binary Switch Report Command, reporting its On/Off state to the Controller.
PAGE 4
Command Classes Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.