J Series 2.0, 2.4, and 3.
J Series 2.0, 2.4, and 3.
NOTICES COPYRIGHT AND TRADEMARKS © 2011 Christie Digital Systems USA, Inc. All rights reserved. All brand names and product names are trademarks, registered trademarks or trade names of their respective holders. REGULATORY The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment.
Table of Contents 1: Introduction 1.1 Purchase Record and Service Contacts .......................................................................................1-1 1.1.1 List of Components..............................................................................................................1-1 1.1.2 Key Features ........................................................................................................................1-2 1.2 Safety Warnings and Guidelines ..............................
Table of Contents 5.7 Displays....................................................................................................................................... 5-3 5.7.1 The projector is on but there is no display .......................................................................... 5-3 5.7.2 Severe Motion Artifacts ...................................................................................................... 5-3 5.7.
1 Introduction Every effort has been made to ensure the information in this document is accurate and reliable; however, due to constant research the information in this document is subject to change without notice. 1.1 Purchase Record and Service Contacts Whether the projector is under warranty or the warranty has expired, Christie highly trained and extensive factory and dealer service network is always available to quickly diagnose and correct projector malfunctions.
Section 1: Introduction 1.1.
Section 1: Introduction 1.2 Safety Warnings and Guidelines 1.2.1 General Precautions HIGH BRIGHTNESS. Never look directly into the projector lens. The extreme high brightness can cause permanent eye damage. Always power down the projector and disconnect all power sources before servicing or cleaning. FIRE HAZARD. Keep hands, clothes and all combustible material away from the concentrated light beam of the projector.
Section 1: Introduction 1.2.3 Lamp Precautions WARNING 1-4 Never attempt to access the lamp while the lamp is ON. After turning the lamp OFF, it is crucial that you wait at least 5 minutes before handling the lamp. This provides sufficient time for the lamp cooling fans to properly cool the lamp. For all other precautions critical for safe removal and replacement of the lamp, refer to 4.1. J Series 2.0, 2.4, and 3.0kW Setup Guide 020-100751-01 Rev.
2 Installation and Setup This section explains how to install, connect and optimize the projector for delivery of superior image quality. Illustrations are graphical representations only and are provided to enhance the understanding of the written material. 2.1 Projector Quick Setup and Installation The following instructions are for those preferring a quick setup. Refer to the remaining subsections for detailed setup instructions.
Section 2: Installation and Setup 2. Align the lens interface plate with the lens mount. Align the lens electrical connector with the mating connector on the lens mount. Fully insert the assembly straight into the lens mount opening without turning. Press using your hand as shown in Figure 2-2. NOTE: When installing the lens, ensure that the lens is not inserted at an angle, as this can cause damage. FIGURE 2-2 3. Remove the front lens cap. 4.
Section 2: Installation and Setup FIGURE 2-4 6. Use a 5mm hex screwdriver to fasten the red security screws provided with the lens mount (Figure 2-4), or hand tighten the lens retaining screws attached to the lens. NOTES: 1) Recommended for heaviest lenses such as 0.73:1 and 1.2:1. 2) The red security screws MUST be installed when hoisting the projector overhead, or installing the projector in an overhead position.
Section 2: Installation and Setup • Video Decoder Input Card, depending on the source you can apply the following; • Composite video source to 1-CVBS, using a BNC Cable NOTE: Same signal can be used on 4, 5 or 6 when input is selected as CVBS. • Component input grouping is selected in the projector menu. • A component signal on Inputs 4(Pr), 5(Y), 6(Pb) using BNC Connectors. NOTE: Grouped as a component input, YPbPr. • S-Video to one of the two, 2-SVID or 3-SVID using S-Video cable.
Section 2: Installation and Setup For 3000W Model 1. Remove the locking pin from the bracket surrounding the AC receptacle at the AC inlet of the projector by pressing down on the button on the end of the locking pin, and then pull upwards on the pin to remove it, as shown in Figure 2-6. FIGURE 2-6 2. Open the cap on the AC plug and line up the slot on the plug with the pin on the receptacle. See Figure 2-7. FIGURE 2-7 J Series 2.0, 2.4, and 3.0 kW Setup Guide 020-100751-01 Rev.
Section 2: Installation and Setup 3. Insert the plug fully on to the receptacle. When fully inserted, the cap on the AC plug will rest against the side of the projector (Figure 2-8). 4. Reinsert the locking pin into the bracket surrounding the AC receptacle by pressing down on the button on the end of the locking pin and insert the pin into the bracket, as shown in Figure 2-8. Do not attempt operation if the AC supply and cord is not within the specified ratings.
Section 2: Installation and Setup STEP 6 - Selecting a Source Press one of the input keys on the remote or built-in keypad to select and display the image for the source you connected in Step 3. STEP 7- Adjusting Image Adjust the image settings, such as Brightness, Contrast, Gamma, Focus, Zoom etc. using the direct keys on the remote or built in keypad. NOTE: Refer to 3 Operation for more details. 2.
Section 2: Installation and Setup 3. Center the image in the lens: Holding a piece of paper at the lens surface, adjust offsets as necessary until the image is centered within the lens perimeter. A full white field works best for this. 4. If necessary, center the image on the screen: If the projector is mounted off center to the screen axis, then offset the lens as much as required.
Section 2: Installation and Setup 2. Focus the image on cross-hair pattern I. Evaluate the focus on cross-hair image II and III. If all 3 images are in focus, no further action is required. If boresight is required see step 3. 3. If boresight is required, refer to Figure 2-11 to understand how the adjustment screws on the lens mount affect the corresponding cross-hairs on the test pattern. NOTE: The cap screw, (Figure 2-12) may be under a plastic cap, remove and retain before adjusting. 4.
Section 2: Installation and Setup 11. Lock the setscrews, and re-check the boresight quality. Tighten the setscrew enough to ensure they will not shift. FIGURE 2-13 2.2.4 Powering Down The projector can be powered down by using one of the following methods: Remote Keypad/Built-In Keypad • Press and hold POWER OR • Press POWER twice OR • Press POWER once, then immediately press the DOWN key.
Section 2: Installation and Setup 2.2.5 Projector Communications Status LEDs Looking from the back of the projector, the LEDs represent, from left to right; Lamp, Comm, Status, and Shutter.
3 Operation This section describes the controls and switches used for basic projector operation once it is properly installed, aligned and configured by a Christie accredited service technician. Refer to Safety Warnings and Guidelines in 4 . 3.1 Using the Remote Keypad or Built-In Keypad The projector is typically controlled using one of the following keypads: • Remote Keypad for wired or wireless control up to 25 feet (8m) away (includes cable for use as a wired remote).
Section 3: Operation Remote Keypad FIGURE 3-1 REMOTE KEYPAD 3-2 J Series 2.0, 2.4, and 3.0 kW Setup Guide 020-100751-01 Rev.
Section 3: Operation Wired Remote You can convert the remote keypad into a wired remote keypad using the cable provided with the projector. Connect one end into the remote and the other to the XLR connector on the input panel labeled as wired keypad. The wired remote is recommended when: • The built-in keypad is inaccessible • The lighting conditions are unsuitable for proper IR transmission NOTE: Leave the batteries in the wired remote for the laser pointer key to work.
Section 3: Operation • Power Key, used to switch from Standby mode to ON, and from ON to Standby mode; LED always remains Amber • Help Key, only available in the On Screen Display (OSD) context; LED is Amber when the menu is being displayed on the projected image display; when no menu is being displayed, the Help key is still enabled if the OSD is enabled. It is only disabled when the entire OSD is set to OFF. • Auto Key, enabled state when the power is ON, and there are no test patterns on the screen.
Section 3: Operation Channel Select a specific source setup (channel) defined and stored in projector memory. Once you enter a two-digit channel number (or, if there is a list displayed, highlight it and press ENTER), the display will automatically change and update according to the numerous setup parameters defined for that channel. NOTE: A new channel is automatically created if you adjust an image from a new source.
Section 3: Operation Number Keys Press 1 to 9 to enter a value in a text box or to select a menu item. 10+ Press 0 before pressing another number to enter a number greater than 9, e.g. press 0 then 2 to enter the number 12 as a menu selection. NOTE: When entering numbers in a text field, this button acts as 0. Help Press HELP to display context-sensitive help. Press HELP again to toggle the help window OFF. Menu Press MENU to enter or exit the projector menu system.
Section 3: Operation IF WITHIN A PRESENTATION: Press FUNC followed by two numeric numbers to enable a specific color or colors in the display (see right). For example, will display only red, and will display green data. Eliminating one or more colors can help with certain diagnostics and setups, such as when accurately overlaying one image on top of another from stacked projectors. NOTE: Color enabling can also be implemented from numerous locations within the menu system.
Section 3: Operation Lens H and Lens V When adjusting the image for focus, zoom or horizontal and vertical positioning, use the specific arrow keys (LEFT/RIGHT ARROW KEY or UP/DOWN ARROW KEY) related to each function. A small window will appear to indicate the type of adjustment taking place. For example, • • • • Use the FOCUS and the LEFT ARROW or RIGHT ARROW KEY to improve image clarity as desired. Use the ZOOM and the LEFT ARROW or RIGHT ARROW KEY to achieve a desired image size.
Section 3: Operation On-line Help Press HELP to display summary information about the current menu or highlighted option. Press HELP again to exit. The Global Icon Menu options that include this icon apply universally. Menu options without this icon apply to the selected channel only, or are unsaved diagnostic settings. Using Slide bars and Other Controls Most of the function menus allow you to change settings by using slide bars, check boxes, and pull-down lists.
Section 3: Operation “Direct” slide bars - For quick access, to Gamma, Brightness, and Contrast slide bars without traveling the menu system. Press Gamma, Brightness, or Contrast to display the contrast slide bar. Use the arrow keys to adjust a direct slide bar, or press ENTER and enter a specific number from the keypad, then ENTER or LEFT ARROW KEY or RIGHT ARROW KEY to save (or EXIT to cancel). When you are done, press EXIT to save and return to your presentation.
Section 3: Operation Navigate Within the Edit Window: Press RIGHT ARROW KEY to move the cursor forward or LEFT ARROW KEY to move the cursor backwards as desired. Edit a character: To edit a highlighted character, use UP ARROW KEY and DOWN ARROW KEY to scroll through the alphabet, numbers, spaces and punctuation available. When the character you need appears, press RIGHT ARROW KEY to select it—the cursor will move to the next available character of current text.
Section 3: Operation 3.3 Alarms There are two types of alarms: • Warning Alarm • Critical Alarm A warning alarm is generated when an error or a non-optimal condition has occurred that will not prevent the projector from operating. An example is when a temperature is slightly elevated. A critical alarm is generated when a condition occurs that could prevent the projector from operating and could cause damage to the projector. This may cause the projector to shut down automatically.
4 Maintenance 4.1 Lamp and Filter Replacement Lamp Do not operate the lamp for more than the warranty limit; risk of the lamp shattering increases as a result of changes in the quartz glass that occur with use. Operation beyond the lamp warranty limit also significantly reduces brightness output. Wait approximately 5 minutes after powering down the projector to allow the lamp to cool sufficiently before removing. Never attempt to remove the lamp housing directly after use.
Section 4: Maintenance Table 4.1 Projector Part Number Projector Model Roadster S+18K-J 132-013116-xx Mirage S+18K-J 132-013127-xx Roadster HD16K-J 132-014117-xx Mirage HD16K-J 132-014128-xx Roadster S+22K-J 132-016119-xx Mirage S+22K-J 132-016120-xx Roadster HD20K-J 132-017110-xx Mirage HD20K-J 132-017121-xx Roadster WU20K-J 132-018111-xx Mirage WU20K-J 132-018122-xx Matrix WU20K-J 132-018133-xx Lamp Type Lamp/Filter Kit Required 2.4 kW 03-900518-xx 3.0 kW 003-000306-xx 1.
Section 4: Maintenance 4. UNSCREW HANDLE Unscrew the knob on the insertion/removal handle either by hand or using a Phillips screwdriver. See Figure 42. FIGURE 4-2 5. REMOVE THE LAMP MODULE Make sure the lamp insertion/removal handle hook is located behind the lamp module (Figure 4-3) and pull lamp module off of electrical terminal by pulling on the insertion/removal handle. Carefully pull on the lamp module handle to remove the lamp.
Section 4: Maintenance 7. INSERT THE NEW LAMP MODULE Align the base plate of the new lamp module under both side alignment guides (Figure 4-4) then slide the module into the projector in the same orientation you removed the old lamp module until the resistance increases. NOTE: A slightly harder push may be required to ensure it is fully seated. Lamp alignment marks are provided to indicate the fully seated position. FIGURE 4-4 8.
Section 4: Maintenance Filter Replacement Procedure Only use Christie approved filters. See Table 4.1 The filter located at the front side of the projector and should be replaced whenever the lamp is replaced. If you are working in an extremely dusty environment you may want to replace the filter sooner. If this filter is not replaced, airflow may become restricted and cause the projector to overheat.Use the filter provided in the Christie approved Lamp and Filter Kit for your specific projector model.
Section 4: Maintenance Check Liquid Coolant Level 1. Remove the 3 stacking mounts, if installed. 2. Release the 8 quick release screws that secure the top cover. 3. Lift the top cover off and set aside. 4. Locate the Liquid Cooling Module and inspect the liquid level window. NOTE: The arrow is next to the window which indicates the “MIN FILL LEVEL”. Refer to Figure 4-7. 5. If coolant is below the “MIN FILL LEVEL” add more coolant. Refilling Liquid Coolant Module 1.
Section 4: Maintenance LEFT RIGHT FIGURE 4-8 J Series 2.0, 2.4, and 3.0 kW Setup Guide 020-100751-01 Rev.
5 Troubleshooting If the projector is not operating properly, note the symptoms and use this section as a guide to resolve the problem. If the problem cannot be resolved, contact your dealer for assistance. NOTE: A Christie accredited service technician is required when opening an enclosure to diagnose any “probable cause”. 5.1 Power 5.1.1 Projector Does Not Power ON 1. Ensure projector is plugged in? Check power switch above power cord is in the ON position. 2. Check that the Status LEDs are ON.
Section 5: Troubleshooting 5.2.2 Lamp Suddenly Turns OFF 1. Check lamp power through the remote keypad checking the Lamp menu or from the web user interface Advanced: Lamp menu. Try increasing lamp power. 2. Check for an alarm condition on the LCD keypad display. 3. Replace the lamp. 5.2.3 Flicker, Shadows Or Dimness 1. Check lamp power through the remote keypad checking the Lamp menu or from the web user interface Advanced: Lamp menu. Try increasing lamp power. 2. Replace the lamp. 5.3 LCD 5.3.
Section 5: Troubleshooting 5.5 OSD 5.5.1 The OSD Menu does not display 1. Using the LCD, ensure that OSD menu is enabled, scroll-down until the item OSD appears. The LCD shows “OSD: off”. Press and hold the OSD soft key on the built-in keypad. The LCD now shows “OSD on” then press the menu key on the remote keypad. OR 2. Press and hold the OSD key on the remote keypad for 2-3 seconds, then press the menu key. 5.6 Ethernet 5.6.1 Trouble Establishing Communication with Projector 1.
Section 5: Troubleshooting 5.7.3 Image Appears ‘Squeezed’ or Vertically Stretched into Center of Screen 1. Run auto setup, pressing Auto button on the remote keypad. 2. Check your Resizing selection. 5.7.4 The Display is Jittery or Unstable 1. If the display is jittery or blinking erratically, ensure that the source is properly connected and of adequate quality for detection. With poor quality or improperly connected source, the projector will repeatedly attempt to display an image, however briefly. 2.
Section 5: Troubleshooting 5.7.11 Display has Suddenly Frozen If the screen blacks out inexplicably, it is possible that excessive voltage noise on the AC or ground input has interrupted the projector ability to lock on to a signal. Power down the projector and disconnect from AC. Then plug in again and power up as usual. 5.7.12 Colors in the Display are Inaccurate 1. The color, tint, color space and/or color temperature settings may require adjustment at your input source. 2. Try Auto Setup. 3.
Section 5: Troubleshooting 5.8 Web Interface 5.8.1 After upgrading the projector software, the Web pages do not display correctly 1. After upgrading, the temporary internet files and cookies must be cleared from the Web Internet Browser to ensure that Web UI changes can take effect. 2. Using the Internet Explorer menu bar, select Tools> Internet Options. Click Delete from the Browsing history option. Click Delete files. Once the Delete Files window displays, click Yes. Then click Delete cookies.
Section 5: Troubleshooting Using the Internet Option window, select Local intranet, then click Custom Level. Repeat Step 3. FIGURE 5-1 J Series 2.0, 2.4, and 3.0 kW Setup Guide 020-100751-01 Rev.
7 Specifications This section provides detailed J Series features; including inputs, lamp, and power requirements. NOTE: Due to continuing research, detailed features are subject to change without notice. 7.1 Feature Set 7.1.1 Air Filters (Optional) Filter media types Filter access Dust filter Fog filter Service-interchangeable via access panel 7.1.2 Lamps Ushio Xenon bubble lamp system 7.2 Lamps are accessed from the rear of the projector Input (Source Signal) Compatibility 7.2.
Section 6: Specifications 7.
Section 6: Specifications 7.5 Accessories and Service Components Product Name Part Number Analog Input Dual Link DVI Input Video Decoder Input Dual 3G/HD/SD-SDI Input Card Twin HDMI Input DMX512 Interface Dust Filter Fog Filter Lens ILS 0.73:1SX+/0.67:1HD Lens ILS 1.25-1.6SX+/1.16-1.49HD Lens ILS 1.5-2.0SX+/1.4-1.8HD Lens ILS 2.0-2.8SX+/1.8-2.6HD Lens ILS 2.8-4.5SX+/2.6-4.1HD Lens ILS 4.5-7.5SX+/4.1-6.9HD Lens ILS 7.5-11.2SX+/6.9-10.4HD Lens ILS 1.2SX+/1.1HD Lens ILS 1.2SX+/1.
Section 6: Specifications 7.6 Regulatory • • • • CAN/CSA C22.2 No. 60950-1-07 2nd Edition UL 60950-1, 2nd Edition IEC 60950-1:2005, 2nd Edition EN60950:2006 + A11:2009 7.6.1 Electro-Magnetic Compatibility Emissions • FCC CFR47, Part 15, Subpart B, Class A - Unintentional Radiators • CISPR 22: 2008-09/EN55022: 2006 + A1:2007 Class A - Information Technology Equipment Immunity • CISPR 24: 1997 +A1:2001+A2:2002/ EN55024: 1998 +A1:2001 +A2:2003 EMC Requirements - Information Technology Equipment 7.6.
Section 6: Specifications 7.6.
Appendix A: GPIO This section explains how to use a GPIO link from the projector to external equipment, such as devices for 3D synchronizing. A.1 GPIO Port The GPIO connector located on the input panel provides a flexible method of interfacing a wide range of external I/O devices to the projector. There are 7 GPIO pins available on the 9pin D-Sub GPIO connector, which are configurable via RS-232 commands. The other two pins are reserved for ground and power - see table below for pin identification.
Appendix A: GPIO Configuring the GPIO The GPIO connector can be configured to automate any number of events using the serial command code GIO. Each Pin is defined as either an input or output depending on the desired outcome. Configure the pin as an input if you want the projector to respond to something the device does and as an output if you want the external device to respond to an action taken by the projector.
Corporate offices Worldwide offices USA – Cypress ph: 714-236-8610 United Kingdom ph: +44 118 977 8000 Eastern Europe ph: +36 (0) 1 47 48 100 Singapore ph: +65 6877-8737 Japan ph: 81-3-3599-7481 Canada – Kitchener ph: 519-744-8005 France ph: +33 (0) 1 41 21 00 36 Middle East ph: +971 (0) 4 299 7575 Beijing ph: +86 10 6561 0240 South Korea ph: +82 2 702 1601 Germany ph: +49 2161 664540 Spain ph: + 34 91 633 9990 Shanghai ph: +86 21 6278 7708 For the most current technical documentation, please
