D4K2560 Setup Guide 020-101171-01
D4K2560 Setup Guide 020-101171-01
NOTICES COPYRIGHT AND TRADEMARKS © 2013 Christie Digital Systems USA Inc. All rights reserved. All brand names and product names are trademarks, registered trademarks or trade names of their respective holders. REGULATORY The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment.
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety and Warning Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AC/Power Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Lamp Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Safety Labels . . . . . . . . . . . . . . . . . . . .
Introduction This manual is intended for professionally trained operators of Christie high-brightness projection systems. These operators are qualified to replace the lamp and air filter, but should not attempt to install or service the projector. Only accredited Christie technicians who are knowledgeable about the hazards associated with high-voltage, ultraviolet exposure, and the high temperatures generated by the projector lamp are authorized to assemble, install, and service the projector.
Introduction AC/Power Precautions To correctly install this projector, a certified electrician must install a permanent connection to the projector head. Operate the projector at the recommended voltage. Disconnect projector from AC before opening any enclosure. Failure to comply results in death or serious injury.
Introduction Product Safety Labels Indicates the presence of a grounding point. Indicates the presence of an earth grounding point. Indicates the presence of a dangerous condition or situation. Indicates the presence of a pinch hazard. To avoid personal injury, keep hands clear and loose clothing tied back. Indicates the presence of a hot surface. To avoid personal injury, always allow the projector to cool down for a minimum of 10 minutes before performing maintenance or service procedures.
Introduction Always disconnect all power sources before performing maintenance or service procedures. See the product user manual for specific information and directions. See the product service manual for specific information and directions. Do not look directly into the lens. Projector Overview The D4K2560 is a professional quality, easy-to-use projector utilizing Digital Light Processing (DLP™) technology from Texas Instruments.
Introduction List of Components Verify the following components were received with the projector: • Touch Panel Controller (TPC) • Lens plug (required for shipping when lens is not installed to prevent contamination of critical optical components) • Light engine removal tool • Convergence tool • Nylon safety strap with clip (required to secure projector to tabletop or optional rack mount) • Warranty Card • Shroud • Low Security Keys • Web Registration Form D4K2560 Setup Guide 020-101171-0
Site Requirements Physical Operating Environment • Maximum Ambient Temperature (operating) 35°C (95°F) • Minimum Ambient Temperature (operating) 10°C (50°F) External Exhaust Ducting The installation site must provide a minimum of 450 CFM (ft 3/min) external exhaust airflow to ensure adequate cooling of the Xenon arc lamp at less than or equal to 25°C (77°F) ambient and less than 3,000 ft (914.4 m) elevation. Above 25°C or 3,000 ft, 600 CFM is required.
Projector Components Projector Components D LAMP SIDE C F E B A G J H LENS SIDE I ID 8 Item Description A Touch Panel Controller (TPC) The TPC is a touch-sensitive screen used to control and monitor operation. For information about TPC controls and settings. B LED Status Indicators LED color and blinking rates provide information about the status of the projector. For information about projector states and status, see the D4K2560 User Manual (P/N: 020-101076-01).
Installation Safety and Warning Guidelines Installation Safety and Warning Guidelines Failure to comply with the following results in death or serious injury: • This product must be installed within a restricted access location which is normally inaccessible by the general public, including workers, visitors and residents in the immediate vicinity, by means of engineering or administrative control measures but is accessible to authorized personnel that may not have specific safety training.
Position the Projector Position the Projector i Keep the projector lens as parallel to the screen as possible, even if significantly above the screen center. When a particularly short throw distance combines with a very wide screen, you may have to forfeit some aim and stay more parallel to the screen. In such cases, some lens offset can reduce the keystone distortion. 1. Position the projector at an appropriate throw distance (projector-to-screen distance) and vertical position.
Connect to AC Power Connect to AC Power Failure to comply with the following could result in death or serious injury: • Certified electrician required during installation. Ground (earth) connection is necessary for safety. Never compromise safety by returning the current through the ground. Connect ground FIRST to reduce shock hazard. • Use an appropriate strain relief connector on the AC supply cable to prevent the cable from rubbing against the LPS knockout plate and becoming damaged.
Connect to AC Power 3. Connect to the terminal block. NOTE: The terminal block accommodates up to an 8 AWG wire. If desired, a 90° strain relief connector can be used to route the power cable in a downward direction. Always connect the ground lead first to reduce shock hazard. • If connecting to permanent power, connect the AC power source to the terminal block, beginning with the ground lead.
Adjust the Projector Tilt and Level Adjust the Projector Tilt and Level The projector’s rear safety strap must be in place before adjusting the projector feet. Do not over-extend the feet. Make sure several threads are engaged into the projector’s baseplate to secure the projector from falling. Failure to comply could result in death or serious injury. The D4K2560 lens should be centered and parallel with the screen. This orientation ensures ideal lens performance with minimal offset.
Install the Touch Panel Controller (TPC) Install the Touch Panel Controller (TPC) 1. Loosen the mounting arm just enough for the end to fit over the ball joint located on the rear panel of the projector. 2. Tighten the mounting arm until it fits tightly on the joint. 3. Connect the cable from the TPC to the connector on the rear panel of the projector. 4. Adjust the TPC angle for optimal viewing. 14 D4K2560 Setup Guide 020-101171-01 Rev.
Connect External Exhaust Ducting Connect External Exhaust Ducting At minimum, a 10-inch (25.4 cm) long, strong metal duct must be installed at the projector and installed to an outside venting duct system to prevent glass shards from exiting the duct in the event of a lamp explosion. Failure to comply could result in death or serious injury. *600 CFM is required in projection rooms with an ambient temperature above 25°C or located at an elevation greater than 3000 feet above sea level.
Lens Setup Lens Setup Keep fingers and other body parts away from the moving parts in the projector. Motors and fans may start without warning. Tie back long hair, remove jewelry and loose clothing before manually adjusting the projector. Failure to comply could result in death or serious injury. The primary lens seals the projection head, preventing contaminants from entering the main electronics area. Do not operate the projector without a lens installed.
Lamp Setup Calibrate the Lens Motors If the lens motors are not calibrated properly, implications may include: • Incorrect reporting of the lens motor position. • Inability to use the full range of the lens motors. • Lens motors traveling outside of the pre-defined keep-out area. • Damage to the projector. Reset and calibrated the lens motors when any of the following conditions are met: • After a lens change. • After the lens motors are physically moved using the manual adjustment knobs.
Connect Devices Connect Devices i The GPIO connector located on the MCPU faceplate is for future use. This section provides information and procedures for connecting external devices to the D4K2560 projector. Communication and input ports are located on the projector side input panel, accessed by removing the input panel cover. When connecting devices, route all cables along the channels located on the bottom of the projector and up through the opening in the frame to the communication port.
Connect Devices Connect a Video Source via DisplayPort The Twin DisplayPort Input Card (TDPIC) accepts digital image data from DisplayPort inputs. Connect 4 DisplayPort cables to the 1-IN and 2-IN inputs of both TDPIC input cards. Each DisplayPort input supplies one quadrant of the 4K input image. Connect a Video Source via DVI The optional Dual DVI Input Card (DDIC) accepts digital image data from DVI inputs.
Connect Devices Ethernet Setup Ethernet is setup to obtain an IP address automatically if there is a DHCP server on the network. To modify IP settings, or manually enter an address: 1. Tap Menu Tab > Configuration > Ethernet Settings > Modify IP Settings. 2. Set the network information for the projector: • To obtain information automatically from the network, tap Automatic. • To manually enter the network information, tap Manual and enter the IP Address, Subnet Mask and Gateway (optional). 3. Click Ok.
Touch Panel Controller (TPC) Touch Panel Controller (TPC) The Touch Panel Controller (TPC) is a touch-sensitive screen, used to control the projector. Use the TPC to control the projector, manage sources, adjust the display, and view status information. The TPC is mounted on the rear of the projector and can be adjusted to improve the viewing angle. There is a side USB port that can be used to download log files and install software upgrades.
Corporate offices Worldwide offices USA – Cypress ph: 714-236-8610 United Kingdom ph: +44 118 977 8000 Eastern Europe ph: +36 (0) 1 47 48 100 Singapore ph: +65 6877-8737 Japan ph: 81-3-3599-7481 Canada – Kitchener ph: 519-744-8005 France ph: +33 (0) 1 41 21 00 36 Middle East ph: +971 (0) 4 299 7575 Beijing ph: +86 10 6561 0240 South Korea ph: +82 2 702 1601 Germany ph: +49 2161 664540 Spain ph: + 34 91 633 9990 Shanghai ph: +86 21 6278 7708 For the most current technical documentation, please